Installation Manual

Pure IP-PBX

Thank you for purchasing this Panasonic product.

Please read this manual carefully before using this product and save this manual for future use.

KX-NS1000: PCMPR Software File Version 001.10000 or later

Model No.

KX-NS1000

System Components

System Components Table

Category Model No. Description

Main Unit KX-NS1000

Main Unit

Activation Key Codes

KX-NSE101 Activation Key for Mobile Extension for 1 User (1

Mobile User)

KX-NSE105 Activation Key for Mobile Extension for 5 Users (5

Mobile Users)

KX-NSE110 Activation Key for Mobile Extension for 10 Users (10

Mobile Users)

KX-NSE120 Activation Key for Mobile Extension for 20 Users (20

Mobile Users)

KX-NSM005 Up to 50 IP Phone Capacity Activation Key (Up to 50

IP Phone)

KX-NSM010 Up to 100 IP Phone Capacity Activation Key (Up to 100

IP Phone)

KX-NSM030 Up to 300 IP Phone Capacity Activation Key (Up to 300

IP Phone)

KX-NSM099 Up to System Limit IP Phone Capacity Activation Key

(System MAX IP Phone)

KX-NSM102 2-Channel IP Trunk Activation Key (2 IP Trunk)

KX-NSM104 4-Channel IP Trunk Activation Key (4 IP Trunk)

KX-NSM108 8-Channel IP Trunk Activation Key (8 IP Trunk)

KX-NSM116 16-Channel IP Trunk Activation Key (16 IP Trunk)

KX-NSM201 1-Channel IP Softphone/IP Proprietary Telephone

Activation Key (1 IPSoftphone/IP PT)

KX-NSM205 5-Channel IP Softphone/IP Proprietary Telephone

Activation Key (5 IPSoftphone/IP PT)

KX-NSM210 10-Channel IP Softphone/IP Proprietary Telephone

Activation Key (10 IPSoftphone/IP PT)

KX-NSM220 20-Channel IP Softphone/IP Proprietary Telephone

Activation Key (20 IPSoftphone/IP PT)

KX-NSM501 1-Channel IP Proprietary Telephone Activation Key (1

IP PT)

KX-NSM505 5-Channel IP Proprietary Telephone Activation Key (5

IP PT)

KX-NSM510 10-Channel IP Proprietary Telephone Activation Key

(10 IP PT)

KX-NSM520 20-Channel IP Proprietary Telephone Activation Key

(20 IP PT)

2 Installation Manual

System Components

Category Model No. Description

KX-NSM701 1-Channel SIP Extension Activation Key (1 SIP

Extension)

KX-NSM705 5-Channel SIP Extension Activation Key (5 SIP

Extension)

KX-NSM710 10-Channel SIP Extension Activation Key (10 SIP

Extension)

KX-NSM720 20-Channel SIP Extension Activation Key (20 SIP

Extension)

KX-NSN001 Activation Key for One-look Network (One-look

Network)

KX-NSN002 Activation Key for QSIG Network (QSIG Network)

KX-NSP001 Standard Activation Key Package (E-mail/Two-way

Recording) for 1 User (Std. Pkg 1 User)

KX-NSP005 Standard Activation Key Package (E-mail/Two-way

Recording) for 5 Users (Std. Pkg 5 Users)

KX-NSP010 Standard Activation Key Package (E-mail/Two-way

Recording) for 10 Users (Std. Pkg 10 Users)

KX-NSP020 Standard Activation Key Package (E-mail/Two-way

Recording) for 20 Users (Std. Pkg 20 Users)

KX-NSP101 Advanced Activation Key Package (E-mail/Two-way

Recording/Mobile/CA Pro) for 1 User (Adv. Pkg 1

User)

KX-NSP105 Advanced Activation Key Package (E-mail/Two-way

Recording/Mobile/CA Pro) for 5 Users (Adv. Pkg 5

Users)

KX-NSP110 Advanced Activation Key Package (E-mail/Two-way

Recording/Mobile/CA Pro) for 10 Users (Adv. Pkg 10

Users)

KX-NSP120 Advanced Activation Key Package (E-mail/Two-way

Recording/Mobile/CA Pro) for 20 Users (Adv. Pkg 20

Users)

KX-NSP201 Mobile Activation Key Package (E-mail/Mobile) for 1

User (Mobile Pkg 1 User)

KX-NSP205 Mobile Activation Key Package (E-mail/Mobile) for 5

Users (Mobile Pkg 5 Users)

KX-NSP210 Mobile Activation Key Package (E-mail/Mobile) for 10

Users (Mobile Pkg 10 Users)

KX-NSP220 Mobile Activation Key Package (E-mail/Mobile) for 20

Users (Mobile Pkg 20 Users)

KX-NSU001 Activation Key for Recording Time Expansion (REC

Time Expansion)

KX-NSU002 Activation Key for Two-way Recording Control

(Two-way REC Control)

Installation Manual 3

System Components

Category Model No. Description

KX-NSU003 Activation Key for Message Backup (Message

Backup)

KX-NSU102 2-Channel Unified Messaging Activation Key (2 UM

Port)

KX-NSU104 4-Channel Unified Messaging Activation Key (4 UM

Port)

KX-NSU201 Activation Key for Unified Messaging E-mail

Notification for 1 User (UM/E-mail 1 User)

KX-NSU205 Activation Key for Unified Messaging E-mail

Notification for 5 Users (UM/E-mail 5 Users)

KX-NSU210 Activation Key for Unified Messaging E-mail

Notification for 10 Users (UM/E-mail 10 Users)

KX-NSU220 Activation Key for Unified Messaging E-mail

Notification for 20 Users (UM/E-mail 20 Users)

KX-NSU299 Activation Key for Unified Messaging E-mail

Notification for All Users (UM/E-mail All Users)

KX-NSU301 Activation Key for Two-way Recording for 1 User (2way

REC 1 User)

KX-NSU305 Activation Key for Two-way Recording for 5 Users

(2way REC 5 Users)

KX-NSU310 Activation Key for Two-way Recording for 10 Users

(2way REC 10 Users)

KX-NSU320 Activation Key for Two-way Recording for 20 Users

(2way REC 20 Users)

KX-NSU399 Activation Key for Two-way Recording for All Users

(2way REC All Users)

KX-NSA010 Activation Key for CA Thin Client Server Connection

(CA Thin Client)

KX-NSA020 Activation Key for Multiple CSTA Connection (CSTA

Multiplexer)

KX-NSA201 Activation Key for CA PRO for 1 User (CA Pro 1 user)

KX-NSA205 Activation Key for CA PRO for 5 Users (CA Pro 5

users)

KX-NSA210 Activation Key for CA PRO for 10 Users (CA Pro 10

users)

KX-NSA240 Activation Key for CA PRO for 40 Users (CA Pro 40

users)

KX-NSA249 Activation Key for CA PRO for 128 Users (CA Pro 128

users)

KX-NSA301 Activation Key for CA ACD Monitor for 1 ICD

Supervisor (CA Supervisor)

KX-NSA401 Activation Key for CA Operator Console (CA Console)

4 Installation Manual

System Components

Category Model No. Description

KX-NSA901 Activation Key for CA Network Plug-in for 1 User (CA

Network 1 user)

KX-NSA905 Activation Key for CA Network Plug-in for 5 Users (CA

Network 5 users)

KX-NSA910 Activation Key for CA Network Plug-in for 10 Users (CA

Network 10 users)

KX-NSA940 Activation Key for CA Network Plug-in for 40 Users (CA

Network 40 users)

KX-NSA949 Activation Key for CA Network Plug-in for 128 Users

(CA Network 128 users)

KX-NSF101 Activation Key for CTI interface (CTI interface)

Physical Cards

FAX Card Slot KX-NS0106 FAX Interface Card (FAX)

DSP Card Slot KX-NS0110 VoIP DSP Card (S Type) (DSP S)

KX-NS0111 VoIP DSP Card (M Type) (DSP M)

KX-NS0112 VoIP DSP Card (L Type) (DSP L)

Storage Memory

Card Slot

KX-NS0135 Storage Memory (S Type) (Storage Memory S)

KX-NS0136 Storage Memory (M Type) (Storage Memory M)

KX-NS0137 Storage Memory (L Type) (Storage Memory L)

Free Slot KX-NS0180 2-Port Analogue Trunk / 2-Port SLT Card (SLC2/

LCOT2)

KX-NS0280 4-Port BRI / 2-Port SLT Card (SLC2/BRI4)

KX-NS0290CE PRI30 / 2-Port SLT Card (SLC2/PRI30)

KX-NS0290 PRI23 / 2-Port SLT Card (SLC2/PRI23)

Doorphone Slot KX-NS0161 Doorphone Interface Card (DOORPHONE)

Note that the types of activation keys are subject to change without notice. For CA activation keys, refer to the documentation for

CA.

Equipment Compatibility

The PBX supports the following equipment:

Cell Stations

DECT

• DECT 8-Channel IP Cell Station Unit Using a V-IPCS4 Card for DECT Portable Station

(KX-NCP0158CE)

DECT 6.0

• DECT 6.0 8-Channel IP Cell Station Unit Using a V-IPCS4 Card for DECT 6.0 Portable Station

(KX-NCP0158)

Installation Manual 5

System Components

Doorphones

• Doorphone (KX-T30865, KX-T7765)

Telephones

Panasonic Proprietary Telephones

• IP proprietary telephones (e.g., KX-NT300 series)

• IP softphones (e.g., KX-NCS8100)

• Portable stations (e.g., KX-TCA364, KX-WT115)

SIP Phones

• KX-UT series SIP phones

• IP conferencing phones (e.g., KX-NT700)

• Third party SIP phones (SIP hardphones/SIP softphones)

Other

• Single line telephones

Note

• For the equipment (e.g., Add-on Key Module, USB Module, Headset) that can be connected to a

particular telephone, refer to the telephone’s manual.

• For other equipment that can be connected to the PBX, refer to "2.1.2 System Connection Diagram".

• The PBX does not support the following Panasonic proprietary telephones:

– Analogue proprietary telephones

– Digital proprietary telephones

– DSS consoles

– KX-NT136 IP proprietary telephone

– KX-NT400 IP proprietary telephone

– KX-HGT100 SIP telephone

Notice

• This PBX supports SIP extensions. However, some PBX features may not be available depending on the

type of telephone.

• Under power failure conditions, the connected telephones may not operate. Please ensure that a separate

telephone, not dependent on local power, is available for emergency use.

• Prior to connection of this product, please verify that the intended operating environment is supported.

Satisfactory performance cannot be guaranteed for the following:

– interoperability and compatibility with all devices and systems connected to this product

– proper operation and compatibility with services provided by telecommunications companies over

connected networks

Note

• Some optional hardware, software, and features are not available in some countries/areas. Please

consult your certified Panasonic dealer for more information.

• In this manual, the suffix of each model number (e.g., KX-NS1000NE) is omitted unless necessary.

List of Abbreviations

• CA ® Communication Assistant

• IP-PT ® IP Proprietary Telephone

• PS ® Portable Station

• SIP Extension ® Extensions of the PBX which use Session Initiation Protocol for communication.

• SLT ® Single Line Telephone

6 Installation Manual

System Components

Introduction

This Installation Manual is designed to serve as an overall technical reference for the Panasonic Pure IP-PBX,

KX-NS1000. It provides instructions for installing the hardware, and programming the PBX using Web

Maintenance Console.

The Structure of this Manual

This manual contains the following sections:

Section 1 Safety Precautions

Provides important information intended to prevent personal injury and property damage.

Section 2 System Outline

Provides general information on the PBX, including the system capacity and specifications.

Section 3 Information about the Activation Keys

Provides information on activation keys, including how to obtain activation keys.

Section 4 Installation

Describes the procedures to install the PBX. Detailed instructions for planning the installation site, optional

service cards, and cabling of peripheral equipment are provided. Further information on system expansion

and peripheral equipment installation is included.

Section 5 Programming with Web Maintenance Console

Describes the installation procedure, structure, and functions of the Web Maintenance Console for

programming IP telephones and the PBX. Further information on programming the PBX for use with SIP

trunks and a VoIP network is included.

Section 6 Troubleshooting

Provides information on the PBX and telephone troubleshooting.

Section 7 Appendix

Provides information on using the PBX with a VoIP network, the ports used by the PBX, and PBX Region

Suffix Codes and Areas.

About the Other Manuals

Along with this Installation Manual, the following manuals are available:

Feature Guide

Describes all basic, optional and programmable features of the PBX.

PC Programming Manual

Provides step-by-step instructions for performing system programming using a PC.

User Manual

Provides operating instructions for end users using IP-PTs, SIP phones, SLTs, or PSs.

About the software version of your PBX

The contents of this manual apply to PBXs with a certain software version, as indicated on the cover of this

manual. To confirm the software version of your PBX, see "How do I confirm the software version of the PBX

or installed cards?" in "2.3 Frequently Asked Questions (FAQ)" of the PC Programming Manual.

Trademarks

• The Bluetooth

word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by

Panasonic Corporation is under licence.

• Microsoft, Outlook, Internet Explorer, Windows and Windows Vista are either registered trademarks or

trademarks of Microsoft Corporation in the United States and/or other countries.

• Mozilla and Firefox are registered trademarks of the Mozilla Foundation.

• All other trademarks identified herein are the property of their respective owners.

• Microsoft product screen shot(s) reprinted with permission from Microsoft Corporation.

Installation Manual 7

Introduction

Table of Contents

1 Safety Precautions .................................................................................11

1.1 For Your Safety ...............................................................................................................12

1.2 Important Safety Instructions ........................................................................................18

1.3 Precautions ......................................................................................................................19

1.4 Data Security ...................................................................................................................22

2 System Outline .......................................................................................23

2.1 Basic System Construction ...........................................................................................24

2.1.1 System Configurations ...................................................................................................24

2.1.2 System Connection Diagram ..........................................................................................26

2.2 Optional Equipment ........................................................................................................28

2.2.1 Optional Equipment ........................................................................................................28

2.3 Specifications ..................................................................................................................30

2.3.1 General Description ........................................................................................................30

2.3.2 Characteristics ................................................................................................................31

2.3.3 System Capacity ............................................................................................................32

3 Information about the Activation Keys ................................................41

3.1 Information about the Activation Keys .........................................................................42

3.1.1 Type and Maximum Number of Activation Keys ............................................................42

3.1.2 Activation Key Code and Key Management System ......................................................56

4 Installation ..............................................................................................57

4.1 Before Installation ...........................................................................................................58

4.1.1 Before Installation ...........................................................................................................58

4.2 Installation of the PBX ....................................................................................................60

4.2.1 Unpacking ......................................................................................................................60

4.2.2 Names and Locations .....................................................................................................61

4.2.3 Opening/Closing the Top Cover .....................................................................................62

4.2.4 Frame Earth Connection ................................................................................................65

4.2.5 Installing/Removing the Optional Service Cards ............................................................66

4.2.6 Installing/Removing the Storage Memory Card ..............................................................79

4.2.7 Types of Connectors ......................................................................................................83

4.2.8 Attaching a Ferrite Core .................................................................................................84

4.2.9 19-inch Rack Mounting ...................................................................................................85

4.2.10 Placing the PBX on a Desktop .......................................................................................86

4.2.11 Wall Mounting .................................................................................................................87

4.2.12 Surge Protector Installation ............................................................................................91

4.3 The Mother Board and Expansion Cards ......................................................................94

4.3.1 Mother Board ..................................................................................................................94

4.3.2 Storage Memory Card (installed by default), Storage Memory S Card (KX-NS0135),

Storage Memory M Card (KX-NS0136), Storage Memory L Card (KX-NS0137) ...........98

4.3.3 DSP S Card (KX-NS0110), DSP M Card (KX-NS0111), DSP L Card

(KX-NS0112) ..................................................................................................................99

4.3.4 FAX Card (KX-NS0106) ...............................................................................................101

4.4 Virtual Cards ..................................................................................................................102

4.5 Physical Trunk and Extension Cards ..........................................................................104

4.5.1 SLC2/LCOT2 Card (KX-NS0180) .................................................................................104

4.5.2 SLC2/BRI4 Card (KX-NS0280) ....................................................................................106

4.5.3 SLC2/PRI30 Card (KX-NS0290CE) .............................................................................110

4.5.4 SLC2/PRI23 Card (KX-NS0290) ..................................................................................113

4.6 The Doorphone Card ....................................................................................................116

8 Installation Manual

Table of Contents

4.6.1 DOORPHONE Card (KX-NS0161) ...............................................................................116

4.7 Connection of SLTs ......................................................................................................118

4.7.1 Maximum Cabling Distances of the Extension Wiring (Twisted Cable) ........................118

4.8 Connecting to a Doorphone, Door Opener, and/or External Sensor .......................119

4.9 Connection of Peripherals ...........................................................................................122

4.10 LAN Connection ............................................................................................................127

4.10.1 LAN Connection for the Main Unit ................................................................................127

4.10.2 LAN Connections for IP Telephones ............................................................................129

4.11 Power Failure Ports ......................................................................................................132

4.12 Starting the PBX ............................................................................................................133

5 Programming with Web Maintenance Console .................................137

5.1 Overview of Web Maintenance Console .....................................................................138

5.2 PC Connection ..............................................................................................................139

5.3 Starting Web Maintenance Console ............................................................................142

5.4 Programming the PBX ..................................................................................................145

5.4.1 Easy Setup Wizard .......................................................................................................145

5.4.2 Enabling the DHCP Server Feature .............................................................................148

5.4.3 Installing the Virtual IP Cards to the PBX .....................................................................149

5.4.4 Installing Additional Activation Keys .............................................................................149

5.4.5 Configuration of the Activation Keys ............................................................................149

5.5 Programming a One-look Network ..............................................................................151

5.6 Programming a H.323 QSIG Network ..........................................................................153

5.6.1 Assigning the Hunt Pattern ...........................................................................................153

5.6.2 Programming the Address Translation Table ...............................................................154

5.6.3 Programming the Network Settings ..............................................................................156

5.7 Programming SIP Trunks .............................................................................................160

5.8 Assigning Networking Information to IP Telephones ................................................162

5.8.1 Assigning IP Addressing Information ...........................................................................162

5.8.2 Setting VLAN Parameters ............................................................................................180

5.8.3 Setting Diffserv Parameters .........................................................................................183

5.8.4 Configuration of IP Ports ..............................................................................................186

5.9 Registering IP Telephones ...........................................................................................192

5.9.1 Registering IP Telephones ...........................................................................................192

5.9.2 De-registering IP Telephones .......................................................................................198

5.10 Configuration of Users .................................................................................................201

6 Troubleshooting ...................................................................................203

6.1 Troubleshooting ............................................................................................................204

6.1.1 Installation ....................................................................................................................204

6.1.2 Connection ...................................................................................................................206

6.1.3 Operation ......................................................................................................................207

6.1.4 Error Messages ............................................................................................................209

6.1.5 Restarting the PBX .......................................................................................................211

6.1.6 Troubleshooting by Error Log .......................................................................................213

7 Appendix ...............................................................................................215

7.1 Information about Using an IP Network ......................................................................216

7.1.1 Using a VoIP Network with the PBX .............................................................................216

7.1.2 DHCP (Dynamic Host Configuration Protocol) Server .................................................219

7.1.3 VLAN (Virtual LAN) ......................................................................................................220

7.1.4 Jitter Buffer ...................................................................................................................221

7.1.5 Voice Activity Detection (VAD) .....................................................................................221

7.1.6 Network Configuration ..................................................................................................222

7.1.7 Network Devices ..........................................................................................................226

Installation Manual 9

Table of Contents

7.1.8 QoS (Quality of Service) ...............................................................................................227

7.2 H.323 Trunks ..................................................................................................................228

7.2.1 Avoid Multiple IP Networks ...........................................................................................228

7.2.2 Gatekeeper ...................................................................................................................229

7.2.3 Bandwidth Assessment ................................................................................................229

7.2.4 Virtual VoIP Gateway Card Specifications ...................................................................232

7.3 SIP Trunks .....................................................................................................................233

7.3.1 IP Telephony Service ...................................................................................................233

7.3.2 SIP Requirements ........................................................................................................236

7.3.3 Router Requirements ...................................................................................................236

7.3.4 Bandwidth Requirements .............................................................................................236

7.3.5 Virtual SIP Trunk Card Specifications ..........................................................................238

7.4 Types of PBX Networks ................................................................................................239

7.4.1 One-look Network .........................................................................................................239

7.4.2 H.323 QSIG Network ....................................................................................................243

7.4.3 Working with Multiple PBX Networks ...........................................................................244

7.5 Port Security ..................................................................................................................245

7.6 PBX Region Suffix Codes and Areas ..........................................................................250

7.7 System Prompt Languages ..........................................................................................252

Index............................................................................................................255

10 Installation Manual

Table of Contents

Section 1

Safety Precautions

This section provides important information intended to

prevent personal injury and property damage.

Installation Manual 11

1.1 For Your Safety

To prevent personal injury and/or damage to property, be sure to observe the following safety precautions.

The following symbols classify and describe the level of hazard and injury caused when this unit is

operated or handled improperly.

WARNING

This notice means that misuse could result in death

or serious injury.

CAUTION

This notice means that misuse could result in injury

or damage to property.

The following types of symbols are used to classify and describe the type of instructions to be

observed.

This symbol is used to alert users to a specific operating procedure that must not be performed.

This symbol is used to alert users to a specific operating procedure that must be followed in

order to operate the unit safely.

12 Installation Manual

1.1 For Your Safety

WARNING

For All Telephone Equipment

• Do not install the product in any other way than described in relevant manuals.

• Do not install the product in a place exposed to rain or moisture, or a place where water, oil, or other liquids

can drip or splash onto on the product. Such conditions can lead to fire or electric shock, and may impair

the performance of the product.

• Do not install the system in the following locations:

a. Areas where shocks or vibrations are frequent or strong. Such activity may lead to the product falling

over and causing injury, or may impair the product’s performance.

b. Areas with high amounts of dust. High amounts of dust can lead to fire or electric shock, and impair

the performance of the product.

• Do not place the product on an unstable or uneven surface. If the product were to fall over, it may cause

injury or damage to the product.

• Do not supply power to a combination of devices that exceeds the total rated capacity of the wall outlets

or extension cables used. If outlets, power strips, extension cords, etc. are used in a manner that exceeds

their rated capacity, they emit large amounts of heat, which could cause a fire.

• The product must only be installed and serviced by qualified service personnel. The product should be

used as-is from the time of purchase; it should not be disassembled or modified. Disassembly or

modification can cause a fire, electric shock, or damage to the product.

• Follow all warnings and instructions marked on the product.

• Products that require a power source should only be connected to the type of electrical power supply

specified on the product label. If you are not sure of the type of power supply to your home, consult your

dealer or local power company.

• For safety purposes some products are equipped with an earthed plug. If you do not have an earthed outlet,

please have one installed. Do not bypass this safety feature by tampering with the plug.

• When installing telephone wiring, basic safety precautions should always be followed to reduce the risk of

fire, electric shock and injury to persons, including the following:

a. Never install telephone wiring during a lightning storm.

b. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.

c. Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected

at the network interface.

d. Use caution when installing or modifying telephone lines.

e. Anti-static precautions should be taken during installation.

• Unplug the product from the wall outlet and have it serviced by qualified service personnel in the following

cases:

a. When the power supply cord or plug is damaged or frayed.

b. If liquid has been spilled into the product.

c. If the product has been exposed to rain or water.

Installation Manual 13

1.1 For Your Safety

d. If the product does not operate according to the operating instructions. Adjust only the controls that are

explained in the operating instructions. Improper adjustment of other controls may result in damage

and may require service by a qualified technician to restore the product to normal operation.

e. If the product has been dropped or the cabinet has been damaged.

f. If product performance deteriorates.

For the PBX

• Do not insert objects of any kind into this product, as they may touch dangerous voltage points or short out

parts that could result in a fire or electric shock.

• Do not pull, bend, rest objects on, or chafe the power cord and plug. Damage to the power cord or plug

can cause fire or electric shock.

• Do not attempt to repair the power cord or plug. If the power cord or plug is damaged or frayed, contact

an authorised Panasonic Factory Service Centre for a replacement.

• When mounting the PBX on a 19-inch rack, only use the 19-inch rack mounting equipment (attachment

bracket, screws) included with the PBX.

• If damage to the unit exposes any internal parts, disconnect the power supply cord immediately and return

the unit to your dealer.

• To prevent fires, electric shock, injury, or damage to the product, be sure to follow these guidelines when

performing any wiring or cabling:

a. Before performing any wiring or cabling, unplug the product’s power cord from the outlet. After

completing all wiring and cabling, plug the power cord back into the outlet.

b. When laying cables, do not bundle the product’s power cord with the power cords of other devices.

c. Do not place any objects on top of the cables connected to the PBX.

d. When running cables along the floor, use protectors to prevent the cables from being stepped on.

e. Do not run any cables under carpeting.

• Unplug this unit from the AC outlet if it emits smoke, an abnormal smell or makes unusual noise. These

conditions can cause fire or electric shock. Confirm that smoke has stopped and contact an authorised

Panasonic Factory Service Centre.

• Make sure that the wall that the unit will be attached to is strong enough to support approximately 4 times

the weight of the unit. If not, it is necessary for the wall to be reinforced.

• When mounting the PBX on a wall, only use the wall-mounting equipment (anchor plugs, screws, metal

brackets) included with the PBX and the wall mounting kit.

• The earthing wire of the AC cable has an effect against external noise and lightning strikes, but it may not

be enough to protect the PBX and to ensure electromagnetic compatibility. A permanent connection

between earth and the earth terminal of the PBX must be made.

• Proper earthing (connection to earth) is very important to reduce the risk to the user of electrocution or to

protect the PBX from the bad effects of external noise in the case of a lightning strike. (See "4.2.4 Frame

Earth Connection".)

• Plug the power cord firmly into an AC outlet. Otherwise, it can cause fire or electric shock.

• Be careful not to drop any components. Dropping components may damage them or cause an injury.

• Make sure that the AC outlet is properly earthed, then securely connect the 3-pin AC plug including the

earthed pin.

• A lithium battery is used in the mother board. There is a risk of explosion if the battery is replaced with the

incorrect type. Dispose of used batteries according to the manufacturer’s instructions.

14 Installation Manual

1.1 For Your Safety

CAUTION

For All Telephone Equipment

• The product should be kept free of dust, moisture, high temperature (more than 40 °C) and vibration, and

should not be exposed to direct sunlight.

• Unplug the product from the wall outlet before cleaning. Wipe the product with a soft cloth. Do not clean

with abrasive powders or with chemical agents such as benzene or thinner. Do not use liquid cleaners or

aerosol cleaners.

For the PBX

• Do not install the system in the following locations:

a. In direct sunlight and hot, cold, or humid places. (Temperature range: 0 °C to 40 °C)

b. Areas where sulphuric gases may be present, such as near thermal springs.

c. Near devices that generate high frequencies, such as sewing machines or electric welders.

• Do not block the openings of the PBX. Allow space of at least 20 cm above and 10 cm at the sides of the

PBX.

• When the PBX is mounted on a 19-inch rack, do not block the openings of the PBX. Allow space of at least

10 cm around the PBX’s fan.

• When installing or removing the Storage Memory Card, do not put pressure on any parts of the mother

board. Doing so may result in damage to the PBX.

• When installing or removing the optional service cards, do not put pressure on any parts of the mother

board. Doing so may result in damage to the PBX.

• The Storage Memory Card contains software for all the processes of the PBX and all the customer data.

Therefore, do not allow unauthorised access to prevent data leakage.

• Once you have started the PBX, if you unplug the PBX, do not initialise it again as described in "System

Initialisation Procedure". Otherwise, your programmed data will be cleared. To restart the PBX, refer to

"6.1.5 Restarting the PBX".

• Before touching the product (PBX, cards, etc.), discharge static electricity by touching ground or wearing

an earthing strap. Failure to do so may cause the PBX to malfunction due to static electricity.

• When relocating the equipment, first disconnect the telecom connection before disconnecting the power

connection. When the unit is installed in the new location, reconnect the power first, and then reconnect

the telecom connection.

• The power supply cord is used as the main disconnect device. Ensure that the AC outlet is located near

the equipment and is easily accessible.

• The hook clip poses a choking hazard. Keep the hook clip out of reach of children.

• Slots and openings in the front, back and bottom of the cabinet are provided for ventilation; to protect it

from overheating, these openings must not be blocked or covered. The openings should never be blocked

Installation Manual 15

1.1 For Your Safety

by placing the product on a bed, sofa, rug, or other similar surface while in use. The product should never

be placed near or over a radiator or other heat source. This product should not be placed in a sealed

environment unless proper ventilation is provided.

• Make sure that the surface behind the PBX is flat and free of obstacles, so that the openings on the back

of the PBX will not be blocked.

• Make sure that the surface behind the PBX is not made of wood.

• When this product is no longer in use, make sure to detach it from the rack or wall.

• Use only the AC power cord included with the PBX.

• When the PBX is mounted on a 19-inch rack, make sure that the installation of the unit does not cause the

temperature of the rack to exceed its limit.

• Make sure to install all necessary optional service cards in the PBX before performing the wall mounting

procedure. If it is necessary to install or remove a card, make sure to detach the PBX from the wall before

installing or removing the card.

• When driving the screws into the wall, be careful to avoid touching any metal laths, wire laths or plates in

the wall.

• When placing the PBX onto the wall, make sure that the arrows on the metal brackets are pointing upward.

If the arrows are not pointing upward, the PBX may fall, resulting in injury.

• When opening the top cover, the power switch must be turned off.

• For safety reasons, close the top cover and tighten the screws before operating the PBX.

• If the PBX is not installed properly using the securing correct methods, the PBX may fall causing serious

damage.

• When the PBX is placed on a desktop, make sure that the PBX is placed as indicated in "4.2.10 Placing

the PBX on a Desktop". Do not place it on its side or upside down.

• Performing surge protection is essential. Make sure to follow the instructions in "4.2.12 Surge Protector

Installation".

• It is strongly recommended to use SSL encrypted communication when the PC is accessing the PBX via

the Internet. To use SSL encryption, routers must have a port set up for https communication.

• To prevent data leakage, render the Storage Memory Card physically unusable before disposal.

• Avoid using the same AC outlet for computers and other office equipment, as noise generated by such

equipment may hamper system performance or interrupt the system.

• Unplug the system from its power source when wiring, and plug the system back in only after all wiring is

completed.

• Trunks should be installed with surge protectors. For details, refer to "4.2.12 Surge Protector

Installation".

• When installing or removing the Storage Memory Card, the power switch must be turned off.

• When installing or removing the optional service cards, the power switch must be turned off.

• For earthing wire, green-and-yellow insulation is required, and the cross-sectional area of the conductor

must be more than 0.75 mm

or 18 AWG.

• When connecting a SLC2/BRI4, SLC2/PRI30 or SLC2/PRI23 card to the trunk, connect through an NT1;

do not connect to the U interface of the trunk directly.

• PRI ports of SLC2/PRI30 and SLC2/PRI23 cards are SELV ports and should only be connected to SELV

services.

• The MOH port and Pager port are SELV ports and should only be connected to approved SELV devices,

or in Australia, via a Line Isolation Unit with a Telecommunications Compliance Label.

• To protect the system, keep the following in mind:

a. Make sure that both connector cases (frame ground) of the RS-232C cross cable (shielded cable) are

conductive. If they are not conductive, make sure that both connector cases of the cable are firmly

connected.

b. If this is not possible, connect the frame of the PBX to the frame of the PC/Printer using an earthing

wire in order to prevent difference in the electrical potentials.

16 Installation Manual

1.1 For Your Safety

Notice

For All Telephone Equipment

• Read and understand all instructions.

For the PBX

• Keep the unit away from heating appliances and devices that generate electrical noise such as

fluorescent lamps, motors and televisions. These noise sources can interfere with the performance of

the PBX.

• If you are having problems making calls to outside destinations, follow this procedure to test the trunks:

a. Disconnect the PBX from all trunks.

b. Connect known working SLTs to those trunks.

c. Make a call to an external destination using those SLTs.

If a call cannot be carried out correctly, there may be a problem with the trunk that the SLT is connected

to. Contact your telephone company.

If all SLTs operate properly, there may be a problem with your PBX. Do not reconnect the PBX to the

trunks until it has been serviced by an authorised Panasonic Factory Service Centre.

Installation Manual 17

1.1 For Your Safety

1.2 Important Safety Instructions

When using your telephone equipment, basic safety precautions should always be followed to reduce the risk

of fire, electric shock and injury to persons, including the following:

• Do not use the product near water, for example, near a bathtub, wash bowl, kitchen sink, or laundry tub,

in a wet basement, or near a swimming pool.

• Avoid using wired telephones during an electrical storm. There is a remote risk of electric shock from

lightning.

• Do not use a telephone in the vicinity of a gas leak to report the leak.

• Rack Mount Instructions—The following or similar rack-mount instructions are included with the installation

instructions:

a. Elevated Operating Ambient—If installed in a closed or multi-unit rack assembly, the operating ambient

temperature of the rack environment may be greater than room ambient. Therefore, consideration

should be given to installing the equipment in an environment compatible with the maximum ambient

temperature (Tma) specified by the manufacturer.

b. Reliable Earthing—Reliable earthing of rack-mounted equipment should be maintained. Particular

attention should be given to supply connections other than direct connections to the branch circuit (e.g.,

use of power strips).

SAVE THESE INSTRUCTIONS

18 Installation Manual

1.2 Important Safety Instructions

1.3 Precautions

For users in the United Kingdom

FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT CAREFULLY.

This appliance is supplied with a moulded three-pin mains plug for your safety and convenience. Should the

fuse need to be replaced, please ensure that the replacement fuse is of the same rating and that it is approved

by ASTA or BSI to BS1362.

Check for the ASTA mark or the BSI mark on the body of the fuse.

If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If you

lose the fuse cover, the plug must not be used until a replacement cover is obtained. A replacement fuse cover

can be purchased from your local Panasonic dealer.

IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE AC OUTLET IN YOUR PREMISES, THEN THE

FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY. THERE IS A

DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT-OFF PLUG IS INSERTED INTO ANY 13 AMP

SOCKET.

If a new plug is to be fitted, please observe the wiring code as shown below. If in any doubt, please consult a

qualified electrician.

WARNING

This appliance must be earthed.

IMPORTANT: The wires in the mains lead are coloured as follows:

Green-and-yellow: Earth

Blue: Neutral

Brown: Live

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings

identifying the terminals in your plug, proceed as follows.

The wire that is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug that is marked

with the letter E or by the safety earth symbol

or coloured GREEN or GREEN-AND-YELLOW.

The wire that is coloured BLUE must be connected to the terminal that is marked with the letter N or coloured

BLACK.

The wire that is coloured BROWN must be connected to the terminal that is marked with the letter L or coloured

RED.

How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse and fuse cover.

The equipment must be connected to direct extension lines, and a payphone should not be connected as an

extension.

999 and 112 can be dialled on the apparatus after accessing the Exchange line for the purpose of making

outgoing calls to the BT emergency services.

Installation Manual 19

1.3 Precautions

During dialling, this apparatus may tinkle the bells of other telephones using the same line. This is not a fault

and we advise you not to call the Fault Repair Service.

For users in the European Union only

Information for Users on Collection and Disposal of Old Equipment and used Batteries

These symbols on the products, packaging, and/or accompanying documents mean that

used electrical and electronic products and batteries should not be mixed with general

household waste.

For proper treatment, recovery and recycling of old products and used batteries, please take

them to applicable collection points, in accordance with your national legislation and the

Directives 2002/96/EC and 2006/66/EC.

By disposing of these products and batteries correctly, you will help to save valuable

resources and prevent any potential negative effects on human health and the environment

which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products and batteries, please

contact your local municipality, your waste disposal service or the point of sale where you

purchased the items.

Penalties may be applicable for incorrect disposal of this waste, in accordance with national

legislation.

For business users in the European Union

If you wish to discard electrical and electronic equipment, please contact your dealer or

supplier for further information.

Information on Disposal in other Countries outside the European Union

These symbols are only valid in the European Union. If you wish to discard these items,

please contact your local authorities or dealer and ask for the correct method of disposal.

Note for the battery symbol (bottom two symbol examples):

This symbol might be used in combination with a chemical symbol. In this case it complies

with the requirement set by the Directive for the chemical involved.

For users in Germany only

• Machine Noise Information Ordinance, 3rd GPSGV: The highest sound pressure level is 70 dB (A) or less

according to EN ISO 7779.

• This equipment is not for use at video display work stations according to BildscharbV.

For users in Finland, Norway and Sweden only

• This equipment is intended for installation in restricted access locations where only authorised personnel

may gain access through the use of a special tool, lock and key or other means of security.

For users in New Zealand only

• This equipment shall not be set to make automatic calls to the Telecom ‘111’ Emergency Service.

• The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted

that the item complies with minimum conditions for connection to its network. It indicates no endorsement

of the product by Telecom, nor does it provide any sort of warranty. Above all, it provides no assurance

20 Installation Manual

1.3 Precautions

that any item will work correctly in all respects with another item of Telepermitted equipment of a different

make or model, nor does it imply that any product is compatible with all of Telecom’s network services.

• This equipment is not capable, under all operating conditions, of correct operation at the higher speeds for

which it is designed. Telecom will accept no responsibility should difficulties arise in such circumstances.

• Some parameters required for compliance with Telecom’s Telepermit requirements are dependent on the

equipment (PBX) associated with this modem. In order to operate within the limits for compliance with

Telecom’s Specifications, the associated PBX equipment shall be set to ensure that modem calls are

answered between 3 and 30 seconds of receipt of ringing.

• Using the toll services of a company other than Telecom:

If the PBX is set up to use the toll services of a company other than Telecom, the telephone numbers

dialled from the Caller Display listings within the PBX will be directed through the toll services of the other

company because the telephone numbers include the toll access digit and area code digit. A toll charge

may be incurred. Please check with the toll carrier concerned.

• APPLICABLE ONLY TO TELECOM CUSTOMERS WHO HAVE AUTOMATIC ACCESS TO OTHER

CARRIERS FOR TOLL CALLS

When calling back a number from the Caller ID list, all numbers prefixed with "0 + AREA CODE" will be

automatically forwarded to your toll carrier. This includes numbers in your local calling area. The zero +

area code should either be removed when calling back local numbers, or check with your toll carrier that

a charge will not be levied.

• All persons using this device for recording telephone conversations shall comply with New Zealand law.

This requires that at least one party to the conversation is to be aware that it is being recorded. In addition,

the principles enumerated in the Privacy Act 1993 shall be complied with in respect to the nature of the

personal information collected, the purpose for its collection, how it is used, and what is disclosed to any

other party.

• The SLT ports are not specifically designed for 3-wire-connected equipment. 3-wire-connected equipment

might not respond to incoming ringing when attached to these ports.

For users in Australia only

• No External TRC Terminal is provided due to an Internal Link between PE and TRC.

For users in Taiwan only

• Lithium batteries can be found in the circuit boards of the mother board and optional service cards of the

PBX.

Notice

Regarding removing or replacing a battery in the circuit board, consult your dealer.

Note

• When disposing of any of the above products, all batteries must be removed. Follow the applicable

laws, regulations, and guidelines in your country/area regarding disposal of batteries.

• When replacing a battery, use only the same battery type, or an equivalent recommended by the battery

manufacturer.

Installation Manual 21

1.3 Precautions

1.4 Data Security

In order to use the PBX safely and correctly, the Security Requirements below must be observed. Failure to

do so may result in:

• Loss, leakage, falsification or theft of user information.

• Illegal use of the PBX by a third party.

• Interference or suspension of service caused by a third party.

What is User Information?

User Information is defined as:

1. Information stored on the Storage Memory Card:

System data, error data and activation key files.

2. Information sent from the PBX to a PC or a USB memory device:

System data, sound files for MOH (Music on Hold) and OGM (Outgoing Messages), and activation key

files.

Requirements

1. The Storage Memory Card contains software for all the processes of the PBX and all the customer data.

Therefore, do not allow unauthorised access to prevent data leakage.

2. Always make backups of data stored on the Storage Memory Card and/or perform regular system data

backups to a USB memory device.

For details about making backups of data stored on the Storage Memory Card, refer to "7.2.2 Utility—File

—File Transfer PBX to PC" in the PC Programming Manual.

For details about backing up the system data to a USB memory device, refer to "6.1 Tool—System Data

Backup to USB" in the PC Programming Manual.

3. To prevent illegal access from the Internet, activate a Firewall.

4. To avoid unauthorised access and possible abuse of the PBX, we strongly recommend:

a. Keeping the password secret.

b. Selecting a complex, random password that cannot be easily guessed.

c. Changing your password regularly.

5. Perform the following when sending the PBX for repair or handing it over to a third party.

a. Make a backup of data stored on the Storage Memory Card.

b. Using a formatter, format the Storage Memory Card so that information cannot be retrieved from it.

6. To prevent data leakage, render the Storage Memory Card physically unusable before disposal.

7. When user information is sent from the PBX to a PC or a USB memory device, the confidentiality of that

information becomes the responsibility of the customer. Before disposing of the PC or the USB memory

device, ensure that data cannot be retrieved from it by formatting the hard disk and/or rendering it physically

unusable.

22 Installation Manual

1.4 Data Security

Section 2

System Outline

This section provides general information on the PBX,

including the system capacity and specifications.

Installation Manual 23

2.1 Basic System Construction

2.1.1 System Configurations

Main Unit

The main unit contains a mother board for controlling PBX functions.

Stand-alone System

A single KX-NS1000 PBX can be used as a stand-alone system. A single KX-NS1000 used as a stand-alone

system controls all terminals, trunks, and applications.

One-Look Network with NS-Net

Multiple KX-NS1000 PBXs can be connected as a distributed networked system using a private IP network.

The networked system is called a One-look network and it can contain up to 16 KX-NS1000 PBXs. In a

One-look network, one PBX serves as the Master unit, which controls the other PBXs, known as Slave units.

The Slave units share setup information and resources controlled by the Master unit. A One-look network is

useful when the network will consist only of KX-NS1000 PBXs and a private IP network is feasible. A

considerable amount of setup is done automatically by the PBXs, so setup and maintenance is much simpler

than other type of networks, such as a TIE line network. All units can be programmed from one location.

Resource sharing allows users to interact as if they were all connected to one PBX, which eliminates the need

to manage information such as PBX access codes.

For details about programming the One-look network, refer to "5.5 Programming a One-look Network".

For details about using a One-look network, refer to "4.2 One-look Networking" in Feature Guide.

NS-Net is a network protocol only used for Panasonic products.

24 Installation Manual

2.1.1 System Configurations

IP Network

Master Unit

Slave Units

(Up to 15 Units)

.....

H.323 QSIG network

If the network will include non-KX-NS1000 PBXs (e.g., KX-TDE200, KX-NCP500), then an H.323 QSIG

network is necessary.

An H.323 QSIG network is preferable if strict resource separation between sites is necessary. Although it is

possible to reserve certain resources for certain extension users in a One-look network, the default is to share

resources. On the other hand, in a QSIG network, resources are not available to extension users of other PBXs

without explicit programming.

Programming and configuring an H.323 QSIG network is much more complex than a One-look network.

It is also possible to connect a One-look network to other PBXs via QSIG. In an H.323 QSIG network, the

One-look network appears as one PBX. The Master unit represents the One-look network.

For details about programming the H.323 QSIG network, refer to "5.6 Programming a H.323 QSIG

Network".

For details about H.323 QSIG network, refer to "4.2.2 Network Type Comparison" in the Feature Guide.

Installation Manual 25

2.1.1 System Configurations

2.1.2 System Connection Diagram

Doorphone & Door Opener

BGM/Music On Hold (MOH)

Pager/

Speaker

Printer

Router

Trunk (Telephone Company Lines)

Analogue/BRI/PRI

Pure IP-PBX

Remote PC

Fax Machine

Amplifier

SLT

External Sensor

IP-PT

IP Softphone, CA

Client PC

CTI Server

Private

IP Network

ITSP

Network

DCE

(e.g., ADSL

Modem)

WAN

IP-CS PS

SIP Phone

ITSP: Internet Telephony Service Provider

DCE: Data Circuit Terminating Equipment

CA: Communication Assistant

26 Installation Manual

2.1.2 System Connection Diagram

SLT Fax Machine

DSP S

(KX-NS0110)

DSP M

(KX-NS0111)

DSP L

(KX-NS0112)

V-IPGW16

V-IPEXT32

V-SIPGW16

V-SIPEXT32

V-IPCS4

V-UTEXT32

FAX

(KX-NS0106)

Storage

Memory

(Installed by

default)

Storage

Memory S

(KX-NS0135)

Storage

Memory M

(KX-NS0136)

Storage

Memory L

(KX-NS0137)

Doorphone & Door Opener

Mountable Equipment

External Sensor

Telephone

Company

Analogue

Trunk

ISDN BRI Line

(Digital Trunk)

ISDN PRI Line

(Digital Trunk)

Router

Amplifier Pager/Speaker

IP Softphone,

CA Client PC

LAN

CTI Server

IP-PT

IP-CS

Private IP

Network

ITSP

Network

DCE

(e.g., ADSL

Modem)

WAN

Router

DOORPHONE

(KX-NS0161)

SLC2/LCOT2

(KX-NS0180)

SLC2/BRI4

(KX-NS0280)

SLC2/PRI30

(KX-NS0290CE)

SLC2/PRI23

(KX-NS0290)

Radio

Station Message

Detail Recording (SMDR)

SIP Phone

Uninterruptible Power

Supply (UPS)

Virtual Slot

USB Memory Device

Installation Manual 27

2.1.2 System Connection Diagram

2.2 Optional Equipment

2.2.1 Optional Equipment

Model No. Model Name Description

KX-NS0106 FAX Interface Card (FAX) 1-channel fax server. To be mounted on the

mother board.

KX-NS0110 VoIP DSP Card (S Type) (DSP S) A DSP card is a digital signal processor card with

DSP resources that can be used for VoIP calls,

conferences, the Unified Messaging feature, and

the DISA/OGM feature. The DSP cards are

compliant with ITU-T G.729A and G.711 codec

methods.

Depending on the amount of your DSP resource

needs, DSP S, DSP M, or DSP L cards can be

installed. The number of resources provided by

each type of DSP card is as follows:

• DSP S card: 63

• DSP M card: 127

• DSP L card: 254

Up to 2 DSP cards can be installed on the mother

board.

To operate the PBX, at least one DSP S,

DSP M, or DSP L card must be installed in one

of the DSP card slots.

KX-NS0111 VoIP DSP Card (M Type) (DSP M)

KX-NS0112 VoIP DSP Card (L Type) (DSP L)

KX-NS0135 Storage Memory (S Type)

(Storage Memory S)

Storage Memory with maximum of 200 hours

Voice Mail recording time.

KX-NS0136 Storage Memory (M Type)

(Storage Memory M)

Storage Memory with maximum of 450 hours

Voice Mail recording time.

KX-NS0137 Storage Memory (L Type)

(Storage Memory L)

Storage Memory with maximum of 1000 hours

Voice Mail recording time.

KX-NS0161 Doorphone Interface Card

(DOORPHONE)

1-port doorphone card for 1 doorphone, 1 door

opener, and 1 external sensor.

KX-NS0180 2-Port Analogue Trunk / 2-Port

SLT Card (SLC2/LCOT2)

A combination card including:

• 2 analogue trunk ports with Caller ID (FSK/

FSK with Call Waiting Caller ID [Visual Caller

ID]/DTMF). One port is a power failure

transfer (PFT) port.

• 2 extension ports with Caller ID (FSK) for

SLTs.

KX-NS0280 4-Port BRI / 2-Port SLT Card

(SLC2/BRI4)

A combination card including:

• 4 ISDN Basic Rate Interface ports.

• 2 extension ports with Caller ID (FSK) for

SLTs.

EURO-ISDN/ETSI compliant.

28 Installation Manual

2.2.1 Optional Equipment

Model No. Model Name Description

KX-NS0290CE PRI30 / 2-Port SLT Card (SLC2/

PRI30)

A combination card including:

• 1 ISDN Primary Rate Interface port (30B

channels).

• 2 extension ports with Caller ID (FSK) for

SLTs.

EURO-ISDN/ETSI compliant.

KX-NS0290 PRI23 / 2-Port SLT Card (SLC2/

PRI23)

A combination card including:

• 1 ISDN Primary Rate Interface port (23B

channels).

• 2 extension ports with Caller ID (FSK) for

SLTs.

NI (North American standard ISDN protocol)

compliant.

Note

For the maximum number of optional service cards that can be installed in the PBX, refer to "2.3.3 System

Capacity".

Installation Manual 29

2.2.1 Optional Equipment

2.3 Specifications

2.3.1 General Description

Main CPU 650 MHz Dual Core

Power Input 100 V AC to 130 V AC: 0.95 A/200 V AC to 240 V AC: 0.6 A;

50 Hz/60 Hz

Power Consumption (when fully

mounted)

50 W

(240 V: 132 VA, 200 V: 120 VA, 130 V: 104 VA, 100 V: 95 VA)

External Backup Battery External battery port is not supported.

Support UPS: USB2.0: 1 port (Connector: Type A)

Memory Backup Duration 7 years

Dialling Trunk Dial Pulse (DP) 10 pps, 20 pps

Tone (DTMF) Dialling with Caller ID (FSK/DTMF)

1600 W Maximum

Extension Dial Pulse (DP) 10 pps, 20 pps

Tone (DTMF) Dialling with Caller ID (FSK/DTMF)

SLC1 port supports PFT in combination with the LCOT1 port

connected to an analogue trunk.

Mode Conversion DP-DTMF, DTMF-DP

Ring Frequency 20 Hz/25 Hz (selectable)

Operating

Environment

Temperature 0 °C to 40 °C

Humidity 10 % to 90 % (non-condensing)

Conference Call Trunk

From 24 ´ 3-party conference call to 9 ´ 8-party conference call

Music on Hold (MOH) 1 port (Level Control: -31.5 dB to +31.5 dB per 0.5 dB)

MOH: Selectable Internal/External Music Source port

External Paging 1 port (Volume Control: -15.5 dB to +15.5 dB per 0.5 dB)

Serial Interface Port RS-232C 1 (maximum 115.2 kbps)

RJ45 Port MNT Port 1 (for PC connection) 10BASE-T/100BASE-TX/

1000BASE-T (Auto MDI/

MDI-X)

LAN Port 1 (for LAN connection)

WAN Port

1 (for WAN connection)

Extension Connection Cable SLT 1-pair wire (T, R)

Air-cooling method FAN

Dimension

430 mm (W) ´ 88 mm (H) ´ 340 mm (D)

Weight (when fully mounted) Under 5.1 kg

The WAN Port is not used with PCMPR Software Version 001.10000.

30 Installation Manual

2.3.1 General Description

2.3.2 Characteristics

Terminal Equipment Loop Limit

• SLT: 600 W including set

• Doorphone: 20 W

Minimum Leakage Resistance

15 000 W minimum

Maximum Number of Extension

Instruments per Line

1 for SLT

Ring Voltage 75 Vrms at 20 Hz/25 Hz depending on the Ringing Load

Trunk Loop Limit

1600 W maximum

Hookswitch Flash/Recall Timing

Range

24 ms to 2032 ms

Door Opener Current Limit 24 V DC/30 V AC, 1 A maximum

External Sensor Current Limit Power to the external sensor is provided from the DOORPHONE card

and must be grounded through the DOORPHONE card. For the

connection diagram, refer to "4.6.1 DOORPHONE Card

(KX-NS0161)". The PBX detects input from the sensor when the

signal is under 100 W.

Paging Terminal Impedance

600 W

MOH (Music on Hold) Terminal

Impedance

10 000 W

Installation Manual 31

2.3.2 Characteristics

2.3.3 System Capacity

Type and Maximum Number of Slots

The PBX supports the following type and number of slots.

Slot Type

Maximum Number

Stand-alone System One-look Network

Physical Slot FAX Card Slot 1 16

Storage Memory Card Slot 1 16

DSP Card Slot 2 32

Free Slot 1 16

Doorphone Slot 1 16

Virtual Slot

Virtual Trunk Card 16 16

Virtual Extension Card 20 32

Virtual IP-CS Card

16 32

Front View Inside View (The top cover is removed.)

EC D HF G

A. Front cover plate for the Doorphone Slot

B. Front cover plate for the Free Slot

C. Free Slot

D. Doorphone Slot

E. Storage Memory Card Slot

F. DSP Card Slot 2

G. DSP Card Slot 1

H. FAX Card Slot

32 Installation Manual

2.3.3 System Capacity

Virtual Slots of the Mother Board

Example:

V-IPGW16 V-IPEXT32 V-SIPEXT32 V-IPCS4

V-UTEXT32

V-SIPGW16

Virtual Slots

Mother Board

Installation Manual 33

2.3.3 System Capacity

Maximum Optional Service Cards

The following number of cards can be installed in the Physical Slots or Virtual Slots of the PBX.

Note

• Any card that exceeds the capacity of the PBX will be ignored.

• When the PBX starts up with an invalid configuration, some cards will be ignored.

Cards Installed in Physical Slots

Card Type

Maximum Number

Stand-alone System One-look Network

Free Slot

1 16

SLC2/LCOT2

1 16

SLC2/BRI4

SLC2/PRI30

SLC2/PRI23

Doorphone Slot

1 16

DOORPHONE

1 16

DSP Card Slot

2 32

DSP S

2 32

DSP M

DSP L

FAX Card Slot

1 16

FAX

1 16

Storage Memory Card Slot

1 16

Storage Memory S

1 16

Storage Memory M

Storage Memory L

34 Installation Manual

2.3.3 System Capacity

Cards Installed in Virtual Slots

Card Type

Maximum Number

Stand-alone System One-look Network

Virtual Trunk Card

16 16

V-IPGW16

3 6

V-SIPGW16

16 16

Virtual Extension Card

20 32

V-IPEXT32

V-SIPEXT32

V-UTEXT32

Virtual IP-CS Card

16 32

V-IPCS4

16 32

Maximum Trunks and Extensions

The PBX supports the following number of trunks and extensions.

Type

Stand-alone System One-look Network

Total Number of Trunks 256 600

Trunk (Virtual Trunk Card) 256 256

H.323 Trunks 48 96

SIP Trunks 256 256

Trunk (Physical Trunk Card) 30 480

Total Number of Extensions 640 1000

Installation Manual 35

2.3.3 System Capacity

Type Stand-alone System One-look Network

Extension (Virtual Extension Card) 640 1000

IP-PT and IP Softphone 128 1000

SIP Phone 640 1000

Extension (Physical Extension Card) 2 32

The maximum number of extension ports is 640 per PBX, and the maximum number of Unified Messaging ports is 24 per PBX. When

24 ports for Unified Messaging are fully activated on the Master unit, the maximum number of extension ports will be less than 640.

One Unified Messaging port is equal to 10 extension ports. Therefore, when all Unified Messaging ports are activated, only up to 400

extensions are available. This condition does not apply for Slave units.

DSP Resources

DSP cards provide digital signal processor (DSP) reference resources, and the PBX uses the resources to

perform various PBX operations. The following illustration shows the concept of DSP resource usage. More

36 Installation Manual

2.3.3 System Capacity

complex situations may necessitate additional resources, and in some cases fewer resources may be

necessary.

Conference

0.5

Outgoing Message

(DISA)

Music on Hold (MOH)/

External Paging (EPG)

Internal MOH

Unified Messaging

1.3

PBX

Doorphone

Analogue

Trunk

2.2

G.729A

G.711

IP Trunk

2.2

G.729A

G.711

IP-CS

2.2

G.729A

G.711

IP-PT

SLT

BRI

PRI

: Required DSP Resources

UM Tone Generator

Echo Canceller

Required DSP Resources Assessment

The maximum number of simultaneous calls, operations and features using IP protocols is determined by the

DSP card installed in the PBX. According to the number of resources required, you can install up to 2 DSP

cards.

To decide how much resources are required for the PBX, the DSP Resource Advisor can be useful.

Note

• Calls cannot be made or received when all of the DSP resources are being used.

• The number of required resources must not exceed the DSP resources installed to the PBX.

• For details about the DSP Resource Advisor, refer to "9.32.1.1 PBX Configuration—Configuration—

DSP Resource—Setting—DSP Resource Advisor" in the PC Programming Manual.

• For information about installing DSP cards, refer to "4.3.3 DSP S Card (KX-NS0110), DSP M Card

(KX-NS0111), DSP L Card (KX-NS0112)".

Installation Manual 37

2.3.3 System Capacity

DSP Resource Reservation

DSP resources can be reserved for certain operations to avoid lack of resources for particular operations.

When the PBXs are connected in a One-look network, you can specify how many resources to allocate to each

branch.

The following examples show cases of allocating and reserving DSP resources.

Note

For details about reserving DSP resources, refer to "5.4.4.1 DSP Resource Reservation" and "5.4.4.2 DSP

Resource Advisor" in the Feature Guide, and "9.32.1.1 PBX Configuration—Configuration—DSP

Resource—Setting—DSP Resource Advisor" in the PC Programming Manual.

Example

In this example, the DSP M (127 DSP resources) is installed and resources are reserved for the following

operations:

• 40 VoIP (G.711) calls

• 10 Conference trunks

• 8 Unified Messaging (includes 3 Two-way recording operations)

• 10 OGM operations

• UM Tone (Fixed)

Reserved Resources

(40 x1) + (10 x 0.5) + (8 x 1.3) + (10 x 2) + 2

=77.4

Free Resources

= 127 - 77.4

= 49.6

Maximum Terminal Equipment

The following shows the number of each terminal equipment type supported by the PBX.

Terminal Equipment Type

Stand-alone System One-look Network

Telephone 640 1000

SLT 2 32

IP-PT

128 1000

SIP Phone 640 1000

IP-CS (8-channel) 64 128

PS 512 512

Doorphone 1 16

Door Opener 1 16

External Sensor 1 16

KX-NT300 series and KX-NT265 (software version 2.00 or later only).

38 Installation Manual

2.3.3 System Capacity

Note for KX-NT265 IP-PT users

The supported card varies depending on the software version of your KX-NT265 IP-PT. To confirm the version,

follow the procedure below:

"AP Version".

Select

"Maintenance".

Software version

is displayed.

While starting up

Select

"Version display".

To exit the programming mode

PROGRAM

SP-PHONE

HOLD HOLD HOLD HOLD

Installation Manual 39

2.3.3 System Capacity

40 Installation Manual

2.3.3 System Capacity

Section 3

Information about the Activation Keys

This section provides information on activation keys,

including how to obtain activation keys.

Installation Manual 41

3.1 Information about the Activation Keys

To use IP trunks and IP telephones on a private IP network using the mother board or to upgrade the software

for enhanced features, you need the appropriate activation keys.

Activation keys are provided via the mother board and the optional activation key files.

3.1.1 Type and Maximum Number of Activation Keys

The PBX supports the following type and number of activation keys. The preinstalled activation keys on the

mother board are shown with "[ ]".

When the number of preinstalled activation keys is not enough for the desired configuration or when you wish

to use enhanced features, additional activation keys in the form of activation key files can be installed using

Web Maintenance Console.

When the PBX is connected in a One-look network, activation keys should be installed on the appropriate PBX

as shown in the tables below.

Note

• Store the downloaded activation key files in your PC or a memory device. They can then be reinstalled

when changing the Storage Memory Card or in an emergency situation.

• For information about how to obtain the additional activation keys, refer to "3.1.2 Activation Key Code

and Key Management System".

• For information about how to install the activation key files using Web Maintenance Console, refer to

"5.4.4 Installing Additional Activation Keys".

IP Trunks

Model No. Activation Key Type Description

Maximum IP Trunks

Stand-alone

System

One-look

Network

KX-NSM102 2 IP Trunk Allows the use of 2 IP trunks (H.

323/SIP).

256 IP trunks

(H.323/SIP)

*1*2*3

KX-NSM104 4 IP Trunk Allows the use of 4 IP trunks (H.

323/SIP).

KX-NSM108 8 IP Trunk Allows the use of 8 IP trunks (H.

323/SIP).

KX-NSM116 16 IP Trunk Allows the use of 16 IP trunks (H.

323/SIP).

You need to set the number of installed activation keys to be used for H.323 trunks through system programming. By default, all

installed activation keys will be used for SIP trunks.

For stand-alone system, the maximum number of IP trunks for H.323 is 48.

For One-look Network, the maximum number of IP trunks for H.323 is 96.

42 Installation Manual

3.1.1 Type and Maximum Number of Activation Keys

Installation in One-look Network System

Activation Keys Master Unit Slave Unit

KX-NSM102 2 IP Trunk

ü ü

KX-NSM104 4 IP Trunk

KX-NSM108 8 IP Trunk

KX-NSM116 16 IP Trunk

IP Telephone Capacity

Note

• Up to 30 IP-PTs/IP softphones/KX-UT series SIP phones/third party SIP phones can be used without

needing any of the following IP telephone capacity activation keys.

• Activation keys for IP telephone capacity are not cumulative; the maximum overall capacity is

determined by the highest-numbered installed activation key.

Model No. Activation Key Type Description

Maximum Capacity of IP

Phones

Stand-alone

System

One-look

Network

KX-NSM005 Up to 50 IP Phone Allows the use of between 31 and

50 IP-PTs/IP softphones/KX-UT

series SIP phones/third party SIP

phones.

Capacity for 50 IP-PTs/IP

softphones/KX-UT series SIP

phones/third party SIP phones

KX-NSM010 Up to 100 IP Phone Allows the use of between 31 and

100 IP-PTs/IP softphones/

KX-UT series SIP phones/third

party SIP phones.

Capacity for 100 IP-PTs/IP

softphones/KX-UT series SIP

phones/third party SIP phones

KX-NSM030 Up to 300 IP Phone Allows the use of between 31 and

300 IP-PTs/IP softphones/

KX-UT series SIP phones/third

party SIP phones.

Capacity for 300 IP-PTs/IP

softphones/KX-UT series SIP

phones/third party SIP phones

KX-NSM099 System MAX IP Phone Allows the use of between 31 and

the system limit for IP-PTs/IP

softphones/KX-UT series SIP

phones/third party SIP phones.

Capacity for

640 IP-PTs/

softphones/

KX-UT series

SIP phones/

third party

SIP phones

Capacity for

1000 IP-PTs/

softphones/

KX-UT series

SIP phones/

third party

SIP phones

Installation Manual 43

3.1.1 Type and Maximum Number of Activation Keys

Installation in One-look Network System

Activation Keys Master Unit Slave Unit

KX-NSM005 Up to 50 IP Phone

ü ü

KX-NSM010 Up to 100 IP Phone

KX-NSM030 Up to 300 IP Phone

KX-NSM099 System MAX IP Phone

IP Telephone

Model No. Activation Key Type Description

Maximum IP Telephones

Stand-alone

System

One-look

Network

KX-NSM201 1 IPSoftphone/IP PT Allows the use of 1 IP-PT/IP

softphone/KX-UT series SIP

phone.

640 IP-PTs/

softphones/

KX-UT series

SIP phones

1000 IP-PTs/

softphones/

KX-UT series

SIP phones

KX-NSM205 5 IPSoftphone/IP PT Allows the use of 5 IP-PTs/IP

softphones/KX-UT series SIP

phones.

KX-NSM210 10 IPSoftphone/IP PT Allows the use of 10 IP-PTs/IP

softphones/KX-UT series SIP

phones.

KX-NSM220 20 IPSoftphone/IP PT Allows the use of 20 IP-PTs/IP

softphones/KX-UT series SIP

phones.

KX-NSM501 1 IP PT Allows the use of 1 IP-PT/KX-UT

series SIP phone.

640 IP-PTs/

KX-UT series

SIP phones

[8 IP-PTs/

KX-UT series

SIP phones]

1000 IP-PTs/

KX-UT series

SIP phones

[256 IP-PTs/

KX-UT series

SIP phones]

KX-NSM505 5 IP PT Allows the use of 5 IP-PTs/

KX-UT series SIP phones.

KX-NSM510 10 IP PT Allows the use of 10 IP-PTs/

KX-UT series SIP phones.

KX-NSM520 20 IP PT Allows the use of 20 IP-PTs/

KX-UT series SIP phones.

44 Installation Manual

3.1.1 Type and Maximum Number of Activation Keys

Model No. Activation Key Type Description

Maximum IP Telephones

Stand-alone

System

One-look

Network

KX-NSM701 1 SIP Extension Allows the use of 1 IP

Conferencing Phone/third party

SIP phone.

640 IP

Conferencing

Phones/third

party SIP

phones

1000 IP

Conferencing

Phones/third

party SIP

phones

KX-NSM705 5 SIP Extension Allows the use of 5 IP

Conferencing Phones/third party

SIP phones.

KX-NSM710 10 SIP Extension Allows the use of 10 IP

Conferencing Phones/third party

SIP phones.

KX-NSM720 20 SIP Extension Allows the use of 20 IP

Conferencing Phones/third party

SIP phones.

You can set how many IP softphones can be used with the installed activation keys through system programming. By default, only

IP softphones can be used with the installed activation keys.

Installation in One-look Network System

Activation Keys

Master Unit Slave Unit

KX-NSM201 1 IPSoftphone/IP PT

ü ü

KX-NSM205 5 IPSoftphone/IP PT

KX-NSM210 10 IPSoftphone/IP PT

KX-NSM220 20 IPSoftphone/IP PT

KX-NSM501 1 IP PT

ü ü

KX-NSM505 5 IP PT

KX-NSM510 10 IP PT

KX-NSM520 20 IP PT

KX-NSM701 1 SIP Extension

ü ü

KX-NSM705 5 SIP Extension

KX-NSM710 10 SIP Extension

KX-NSM720 20 SIP Extension

Installation Manual 45

3.1.1 Type and Maximum Number of Activation Keys

Networking

Model No. Activation Key Type Description

Maximum Activation Keys

Stand-alone

System

One-look

Network

KX-NSN001 One-look Network Allows the use of multi-site

connections using One-look

network feature.

16 activation

keys

KX-NSN002 QSIG Network Allows the use of enhanced

QSIG network features (NDSS,

Centralised Voice Mail, etc.).

1 activation key

This activation key must be installed to each PBX in the One-look network.

Installation in One-look Network System

Activation Keys

Master Unit Slave Unit

KX-NSN001 One-look Network

ü ü

KX-NSN002 QSIG Network

Unified Messaging System (Features)

Model No. Activation Key Type Description

Maximum Activation Keys

Stand-alone

System

One-look

Network

KX-NSU001 REC Time Expansion Allows the use of 15 hours of

recording time for Unified

Messaging. This activation key

works only for the Storage

Memory Card provided with the

PBX. Recording time can be

increased further by upgrading

the Storage Memory Card. For

details, refer to "4.3.2 Storage

Memory Card (installed by

default), Storage Memory S Card

(KX-NS0135), Storage Memory

M Card (KX-NS0136), Storage

Memory L Card (KX-NS0137)".

1 activation

key

16 activation

keys

KX-NSU002 Two-way REC Control Allows a manager/administrator

to use the Automatic Two-way

Recording feature to record other

users.

1 activation

key

16 activation

keys

KX-NSU003 Message Backup Allows the automatic backup of

messages.

1 activation

key

16 activation

keys

Activation keys must be installed to the site where the Unified Messaging mailboxes are located.

46 Installation Manual

3.1.1 Type and Maximum Number of Activation Keys

Installation in One-look Network System

Activation Keys Master Unit Slave Unit

KX-NSU001 REC Time Expansion

ü ü

KX-NSU002 Two-way REC Control

ü ü

KX-NSU003 Message Backup

ü ü

Unified Messaging System (Unified Messaging Ports)

Model No. Activation Key Type Description

Maximum Unified

Messaging Ports

Stand-alone

System

One-look

Network

KX-NSU102 2 UM Port Allows the use of 2 Unified

Messaging ports.

24 Unified

Messaging

ports

[2 Unified

Messaging

ports]

384 Unified

Messaging

ports

[32 Unified

Messaging

ports]

KX-NSU104 4 UM Port Allows the use of 4 Unified

Messaging ports.

Activation keys must be installed to the site where the Unified Messaging mailboxes are located.

Installation in One-look Network System

Activation Keys

Master Unit Slave Unit

KX-NSU102 2 UM Port

ü ü

KX-NSU104 4 UM Port

Installation Manual 47

3.1.1 Type and Maximum Number of Activation Keys

Unified Messaging System (Mailbox)

Model No. Activation Key Type Description

Maximum Mailboxes

Stand-alone

System

One-look

Network

KX-NSU201 UM/E-mail 1 User

Allows the use of an e-mail

(IMAP4) client and e-mail

notification (voice/fax messages)

for 1 user.

1024

mailboxes

16 384

mailboxes

KX-NSU205 UM/E-mail 5 Users

Allows the use of an e-mail

(IMAP4) client and e-mail

notification (voice/fax messages)

for 5 users.

KX-NSU210 UM/E-mail 10 Users

Allows the use of an e-mail

(IMAP4) client and e-mail

notification (voice/fax messages)

for 10 users.

KX-NSU220 UM/E-mail 20 Users

Allows the use of an e-mail

(IMAP4) client and e-mail

notification (voice/fax messages)

for 20 users.

KX-NSU299 UM/E-mail All Users

Allows the use of an e-mail

(IMAP4) client and e-mail

notification (voice/fax messages)

up to the system’s limit.

Activation keys must be installed to the site where the Unified Messaging mailboxes are located.

Installation in One-look Network System

Activation Keys

Master Unit Slave Unit

KX-NSU201 UM/E-mail 1 User

ü ü

KX-NSU205 UM/E-mail 5 Users

KX-NSU210 UM/E-mail 10 Users

KX-NSU220 UM/E-mail 20 Users

KX-NSU299 UM/E-mail All Users

48 Installation Manual

3.1.1 Type and Maximum Number of Activation Keys

Unified Messaging System (Two-way Recording/Two-way Transfer Users)

Model No. Activation Key Type Description

Maximum Users

Stand-alone

System

One-look

Network

KX-NSU301 2way REC 1 User Allows the use of Two-way

Recording/Two-way Transfer for

1 user.

640 users 1000 users

KX-NSU305 2way REC 5 Users Allows the use of Two-way

Recording/Two-way Transfer for

5 users.

KX-NSU310 2way REC 10 Users Allows the use of Two-way

Recording/Two-way Transfer for

10 users.

KX-NSU320 2way REC 20 Users Allows the use of Two-way

Recording/Two-way Transfer for

20 users.

KX-NSU399 2way REC All Users Allows the use of Two-way

Recording/Two-way Transfer up

to the system’s limit.

Installation in One-look Network System

Activation Keys

Master Unit Slave Unit

KX-NSU301 2way REC 1 User

KX-NSU305 2way REC 5 Users

KX-NSU310 2way REC 10 Users

KX-NSU320 2way REC 20 Users

KX-NSU399 2way REC All Users

Cellular Phone Extension

Model No. Activation Key Type Description

Maximum Cellular Phone

Extensions

Stand-alone

System

One-look

Network

KX-NSE101 1 Mobile User Allows the use of 1 cellular phone

extension.

1152 cellular phone

extensions

KX-NSE105 5 Mobile Users Allows the use of 5 cellular phone

extensions.

KX-NSE110 10 Mobile Users Allows the use of 10 cellular

phone extensions.

KX-NSE120 20 Mobile Users Allows the use of 20 cellular

phone extensions.

Installation Manual 49

3.1.1 Type and Maximum Number of Activation Keys

Installation in One-look Network System

Activation Keys Master Unit Slave Unit

KX-NSE101 1 Mobile User

KX-NSE105 5 Mobile Users

KX-NSE110 10 Mobile Users

KX-NSE120 20 Mobile Users

Communication Assistant (CA) User

Model No.

Activation

Key Type

Description

Maximum Activation Keys

Stand-alone

System

One-look

Network

KX-NSA010 CA Thin

Client

Allows the use of CA Client in a thin-client

environment.

KX-NSA020 CSTA

Multiplexer

Allows the use of CSTA Multiplexer.

KX-NSA201 CA Pro 1

user

Allows the use of CA Client Pro for 1 user.

240 users without CA server

(Max. 1022 Users with CA

server)

KX-NSA205 CA Pro 5

users

Allows the use of CA Client Pro for 5 users.

KX-NSA210 CA Pro 10

users

Allows the use of CA Client Pro for 10 users.

KX-NSA240 CA Pro 40

users

Allows the use of CA Client Pro for 40 users.

KX-NSA249 CA Pro 128

users

Allows the use of CA Client Pro for 128

users.

KX-NSA301 CA

Supervisor

Allows the use of CA Client Supervisor for 1

user.

KX-NSA401 CA Console Allows the use of CA Client Operator Console

for 1 user.

KX-NSA901 CA Network

1 user

Allows the use of CA Server network features

for 1 user.

KX-NSA905 CA Network

5 users

Allows the use of CA Server network features

for 5 users.

KX-NSA910 CA Network

10 users

Allows the use of CA Server network features

for 10 users.

KX-NSA940 CA Network

40 users

Allows the use of CA Server network features

for 40 users.

KX-NSA949 CA Network

128 users

Allows the use of CA Server network features

for 128 users.

A maximum of 1022 CA users can be registered. However, CA Server is necessary to register more than 240 CA users.

50 Installation Manual

3.1.1 Type and Maximum Number of Activation Keys

Installation in One-look Network System

Activation Keys Master Unit Slave Unit

KX-NSA010 CA Thin Client

KX-NSA020 CSTA Multiplexer

KX-NSA201 CA Pro 1 user

KX-NSA205 CA Pro 5 users

KX-NSA210 CA Pro 10 users

KX-NSA240 CA Pro 40 users

KX-NSA249 CA Pro 128 users

KX-NSA301 CA Supervisor

KX-NSA401 CA Console

KX-NSA901 CA Network 1 user

KX-NSA905 CA Network 5 users

KX-NSA910 CA Network 10 users

KX-NSA940 CA Network 40 users

KX-NSA949 CA Network 128 users

CTI Licence

Model No. Activation Key Type Description

Maximum Activation Keys

Stand-alone

System

One-look

Network

KX-NSF101 CTI interface Allows the use of the 3rd Party

CTI interface.

Installation in One-look Network System

Activation Keys

Master Unit Slave Unit

KX-NSF101 CTI interface

Packaged Activation Keys

These packaged activation keys include multiple activation keys. Installing one packaged activation key allows

you to install multiple activation key features at once.

For details of each feature, refer to relevant section of this manual:

• E-mail (IMAP4) client and e-mail notification (voice/fax messages)

® Unified Messaging System (Mailbox)

• Two-way Recording/Two-way Transfer

® Unified Messaging System (Two-way Recording/Two-way Transfer Users)

• Cellular phone extension

® Cellular Phone Extension

Installation Manual 51

3.1.1 Type and Maximum Number of Activation Keys

• CA Client Pro

® Communication Assistant (CA) User

Model No. Activation Key Type Description

KX-NSP001 Std. Pkg 1 User Allows the use of the following activation key features for 1 user:

• E-mail (IMAP4) client and e-mail notification (voice/fax

messages)

• Two-way Recording/Two-way Transfer

KX-NSP005 Std. Pkg 5 Users Allows the use of the following activation key features for 5 users:

• E-mail (IMAP4) client and e-mail notification (voice/fax

messages)

• Two-way Recording/Two-way Transfer

KX-NSP010 Std. Pkg 10 Users Allows the use of the following activation key features for 10 users:

• E-mail (IMAP4) client and e-mail notification (voice/fax

messages)

• Two-way Recording/Two-way Transfer

KX-NSP020 Std. Pkg 20 Users Allows the use of the following activation key features for 20 users:

• E-mail (IMAP4) client and e-mail notification (voice/fax

messages)

• Two-way Recording/Two-way Transfer

KX-NSP101 Adv. Pkg 1 User Allows the use of the following activation key features for 1 user:

• E-mail (IMAP4) client and e-mail notification (voice/fax

messages)

• Two-way Recording/Two-way Transfer

• Cellular phone extension

• CA Client Pro

KX-NSP105 Adv. Pkg 5 Users Allows the use of the following activation key features for 5 users:

• E-mail (IMAP4) client and e-mail notification (voice/fax

messages)

• Two-way Recording/Two-way Transfer

• Cellular phone extension

• CA Client Pro

KX-NSP110 Adv. Pkg 10 Users Allows the use of the following activation key features for 10 users:

• E-mail (IMAP4) client and e-mail notification (voice/fax

messages)

• Two-way Recording/Two-way Transfer

• Cellular phone extension

• CA Client Pro

KX-NSP120 Adv. Pkg 20 Users Allows the use of the following activation key features for 20 users:

• E-mail (IMAP4) client and e-mail notification (voice/fax

messages)

• Two-way Recording/Two-way Transfer

• Cellular phone extension

• CA Client Pro

KX-NSP201 Mobile Pkg 1 User Allows the use of the following activation key features for 1 user:

• E-mail (IMAP4) client and e-mail notification (voice/fax

messages)

• Cellular phone extension

52 Installation Manual

3.1.1 Type and Maximum Number of Activation Keys

Model No. Activation Key Type Description

KX-NSP205 Mobile Pkg 5 Users Allows the use of the following activation key features for 5 users:

• E-mail (IMAP4) client and e-mail notification (voice/fax

messages)

• Cellular phone extension

KX-NSP210 Mobile Pkg 10 Users Allows the use of the following activation key features for 10 users:

• E-mail (IMAP4) client and e-mail notification (voice/fax

messages)

• Cellular phone extension

KX-NSP220 Mobile Pkg 20 Users Allows the use of the following activation key features for 20 users:

• E-mail (IMAP4) client and e-mail notification (voice/fax

messages)

• Cellular phone extension

Preinstalled Activation Keys in the Mother Board

Preinstalled activation keys with no expiration date

The following type and number of activation keys are preinstalled on the mother board.

Activation Key

Activated Features

IP Phone Capacity (ch) Capacity for up to 30 IP-PTs/IP softphones/

KX-UT series SIP phones/third party SIP phones

CA Basic-Express

1022 users

IP Proprietary Telephone (ch)

8 IP-PTs/KX-UT series SIP phones

UM Port (ch)

2 Unified Messaging ports

Example: Preinstalled Activation Keys in the Mother Board

Preinstalled activation keys for free trial

The following activation keys are preinstalled on the mother board for the 60-days free trial. They will expire

60 days after pressing the Activate Pre-installed Activation key button to begin the free trial.

Installation Manual 53

3.1.1 Type and Maximum Number of Activation Keys

Activation Key Activated Features

One-look Network

One-look networking feature

Two-way Recording Control

Automatic Two-way Recording feature

Message Backup

Automatic backup of messages

UM/E-mail (128 user)

128 mailboxes

Two-Way Recording (30 users)

30 Two-way Recording/Two-way Transfer users

Mobile Extension (30 users)

30 cellular phone extensions

CA PRO (128 users)

128 CA Pro users

CA Supervisor (1 user)

1 CA Supervisor user

CA Operator Console (1 user)

1 CA Console user

CA Thin Client Server

Use CA in a thin-client environment

CSTA Multiplexer

Multiplexing for CSTA connections

Activation Key Installation Example

The following illustration shows an example of when using 16 SIP trunks, 16 H.323 trunks, 40 IP-PTs, 20 IP

softphones, and 20 KX-UT series SIP phones on a private IP network using the mother board.

54 Installation Manual

3.1.1 Type and Maximum Number of Activation Keys

Example:

Mother Board

V-IPGW16 V-IPEXT32 V-SIPEXT32 V-IPCS4

V-UTEXT32

V-SIPGW16

Desired Item:

16 SIP trunks

Required Activation Key:

KX-NSM116

V-IPEXT32 V-SIPEXT32 V-IPCS4 V-UTEXT32V-IPGW16

V-SIPGW16

Desired Item:

16 H.323 trunks

Required Activation Key:

KX-NSM116

V-IPGW16 V-SIPEXT32 V-IPCS4 V-UTEXT32V-IPEXT32

V-SIPGW16

Desired Item:

40 IP-PTs

20 IP softphones

Required Activation Key:

2 of KX-NSM520s

KX-NSM220

V-IPGW16 V-UTEXT32

V-SIPGW16

V-IPEXT32 V-SIPEXT32

V-IPCS4

Desired Item:

20 KX-UT series

SIP phones

Required Activation Key:

KX-NSM520

Desired Item:

80 IP Telephone Capacity

Required Activation Key:

KX-NSM010

Virtual Slots

Note

• Up to 30 IP-PTs/IP softphones/KX-UT series SIP phones/third party SIP phones can be used without

needing any of the IP telephone capacity activation key files.

• Activation keys for IP telephone capacity are not cumulative; the maximum overall capacity is

determined by the highest-numbered installed activation key. In this case, the Up to 100 IP Phone

activation key (KX-NSM010) is used for 80 IP telephones.

Installation Manual 55

3.1.1 Type and Maximum Number of Activation Keys

3.1.2 Activation Key Code and Key Management System

To obtain additional activation keys, you need to purchase the appropriate activation key codes and access

the Key Management System. You can download the activation keys as an activation key file from the Key

Management System.

To download the activation keys, enter the MPR ID number shown on the back of the main unit, and activation

key number and registration ID provided on each activation key code.

For information about the type of activation key codes available, refer to "3.1.1 Type and Maximum Number

of Activation Keys".

For details about installing the downloaded activation key file(s) in the Storage Memory Card using Web

Maintenance Console, refer to "5.4.4 Installing Additional Activation Keys".

Note

• You can only download the activation key file once using the activation key number and registration ID

provided on the activation key code.

• Up to 8 activation keys can be downloaded as one activation key file.

• Up to 997 activation key files can be installed in the optional upgrade Storage Memory Card.

• It is possible to send the activation key file to a specified e-mail address at the same time as

downloading it to a PC.

• Make sure to backup the downloaded activation key files on your PC.

• When the mother board has to be replaced due to a system malfunction, the MPR-ID for the mother

board is no longer valid. In this case, you need a temporary activation key for maintenance purposes.

The temporary activation key can only be used for a limited time period, and can be downloaded from

the Key Management System in the same way as downloading activation key files.

56 Installation Manual

3.1.2 Activation Key Code and Key Management System

Section 4

Installation

This section describes the procedures to install the

PBX. Detailed instructions for planning the installation

site, installing the main unit and optional service cards,

and cabling of peripheral equipment are provided.

Further information on peripheral equipment installation

is included.

Installation Manual 57

4.1 Before Installation

4.1.1 Before Installation

Please read the following notes concerning installation and connection before installing the PBX and terminal

equipment.

Be sure to comply with all applicable laws, regulations, and guidelines.

Notice

Panasonic assumes no responsibility for injuries or property damage resulting from failures arising out of

improper installation or operation inconsistent with this documentation.

Safety Installation Instructions

WARNING

When installing telephone wiring, basic safety precautions should always be followed to reduce

the risk of fire, electric shock and injury to persons, including the following:

• Never install telephone wiring during a lightning storm.

• Never install telephone jacks in wet locations unless the jack is specifically designed for wet

locations.

• Never touch uninsulated telephone wires or terminals unless the telephone line has been

disconnected at the network interface.

• Use caution when installing or modifying telephone lines.

• Anti-static precautions should be taken during installation.

Installation Precautions

The PBX is suitable for mounting on a 19-inch rack, mounting on a wall, or placing on a desktop, and should

be installed in a location where it is accessible for inspections and maintenance.

To prevent malfunction, noise, or discolouration, follow the instructions below:

WARNING

Do not install the system in the following locations:

• Areas where shocks or vibrations are frequent or strong. Such activity may lead to the product

falling over and causing injury, or may impair the product’s performance.

• Areas with high amounts of dust. High amounts of dust can lead to fire or electric shock, and

impair the performance of the product.

CAUTION

Do not install the system in the following locations:

• In direct sunlight and hot, cold, or humid places. (Temperature range: 0 °C to 40 °C)

• Areas where sulphuric gases may be present, such as near thermal springs.

• Near devices that generate high frequencies, such as sewing machines or electric welders.

• Locations where other objects will obstruct the area around the PBX. Be especially careful to leave at

least 5 cm to the sides of the PBX for ventilation.

Notice

Do not install the system in the following locations:

• On or near computers, or other office equipment, as well as microwave ovens or air conditioners. (It is

preferable not to install the system in the same room as the above equipment.)

58 Installation Manual

4.1.1 Before Installation

• Within 1.8 m of radios and televisions. (Both the PBX and PTs should be at least 1.8 m away from such

devices.)

Do not perform the following:

• Do not block the openings of the PBX.

• Do not stack up the optional service cards.

Wiring Precautions

Be sure to follow these instructions when wiring the unit:

CAUTION

• Avoid using the same AC outlet for computers and other office equipment, as noise generated by such

equipment may hamper system performance or interrupt the system.

• Unplug the system from its power source when wiring, and plug the system back in only after all wiring

is completed.

• Trunks should be installed with surge protectors. For details, refer to "4.2.12 Surge Protector

Installation".

Notice

• Use 1-pair telephone cables when connecting SLTs, data terminals, answering machines, computers,

etc.

• Mis-wiring may cause the PBX to operate improperly. Refer to "Section 4 Installation" when wiring

the system.

• If an extension does not operate properly, disconnect the telephone from the extension line and connect

it again, or turn off the PBX using the power switch, then turn it on again.

• Use twisted pair cable for trunk connection.

• To prevent signal noise from interfering with the performance of the product, do not run unshielded

telephone cables near AC power cables, computer cables, AC power sources, etc. When running

cables near other noise-generating devices or cables, use shielded telephone cables or shield the

telephone cables with metal tubing.

Preparing the Network Environment

Be sure to prepare your network’s environment for the installation of the PBX according to the intended PBX

networking configuration. For details about PBX network configurations, refer to "Section 7 Appendix".

Installation Manual 59

4.1.1 Before Installation

4.2 Installation of the PBX

4.2.1 Unpacking

Unpack the box and check the items below:

Main Unit 1

AC Power Cord 1

19-inch Rack Attachment Bracket 2

Hook Clip 1

CD-ROM 1

Screw 6

The KX-NS1000BX and KX-NS1000XE are supplied with 2 types of AC power cord. Please use whichever is appropriate for the

country/area.

60 Installation Manual

4.2.1 Unpacking

4.2.2 Names and Locations

Front

CD EAB

F G H

Inside

Back

A. STATUS Indicator

B. MASTER Indicator

C. System Mode Switch

D. USB Port

E. MNT Port

F. LAN Port

G. WAN Port

H. MOH Port

I. Doorphone Slot

J. Free Slot

K. BATT ALARM Indicator

L. Pager Port

M. Power Switch

N. Earth Terminal

O. AC Inlet

P. Hook Clip Hole

Q. MPR ID

R. RS-232C Port

S. Top Cover

T. Support Bar

U. Mother Board

For details about the MASTER indicator, refer to "LED Indications".

The WAN Port is not used with PCMPR Software Version 001.10000.

Installation Manual 61

4.2.2 Names and Locations

4.2.3 Opening/Closing the Top Cover

Opening the Top Cover

CAUTION

When opening the top cover, the power switch must be turned off.

1. Confirm that the power switch is turned off.

Power Switch

Note

In order to turn off the PBX’s power, a system shutdown using Web Maintenance Console must first

be performed. For details, refer to "5.5 System Control—System Shutdown" in the PC Programming

Manual.

2. Turn the screws anticlockwise to loosen.

62 Installation Manual

4.2.3 Opening/Closing the Top Cover

3. Slide the top cover then lift it off.

4. Remove the support bar from the PBX.

Closing the Top Cover

1. Place the support bar onto the PBX.

Installation Manual 63

4.2.3 Opening/Closing the Top Cover

2. Place the top cover onto the PBX. Then slide the top cover until it closes properly.

3. Turn the screws clockwise to tighten.

CAUTION

For safety reasons, close the top cover and tighten the screws before operating the PBX.

64 Installation Manual

4.2.3 Opening/Closing the Top Cover

4.2.4 Frame Earth Connection

1. Loosen the screw.

2. Insert an earthing wire (user-supplied).

3. Tighten the screw.

4. Connect the earthing wire to earth.

Screw

Earthing wire

To earth

WARNING

• Proper earthing (connection to earth) is very important to reduce the risk to the user of

electrocution or to protect the PBX from the bad effects of external noise in the case of a

lightning strike.

• The earthing wire of the AC cable has an effect against external noise and lightning strikes, but

it may not be enough to protect the PBX and to ensure electromagnetic compatibility. A

permanent connection between earth and the earth terminal of the PBX must be made.

CAUTION

For earthing wire, green-and-yellow insulation is required, and the cross-sectional area of the conductor

must be more than 0.75 mm

or 18 AWG.

Notice

Be sure to comply with applicable local regulations (e.g., laws, guidelines).

Installation Manual 65

4.2.4 Frame Earth Connection

4.2.5 Installing/Removing the Optional Service Cards

CAUTION

• Before touching the product (PBX, cards, etc.), discharge static electricity by touching ground or

wearing an earthing strap. Failure to do so may cause the PBX to malfunction due to static electricity.

• When installing or removing the optional service cards, the power switch must be turned off.

• When installing or removing the optional service cards, do not put pressure on any parts of the mother

board. Doing so may result in damage to the PBX.

Note

Make sure the AC power cord is not connected to the AC inlet of the PBX.

Installing a DSP Card in a DSP Card Slot

1. Position a DSP card in an open DSP card slot. Then holding the card firmly in place, lower the rear end so

that the holes of the card are aligned with the screw holes.

Note

There are 2 DSP card slots on the mother board. When installing only 1 DSP card, only one DSP card

slot will be used.

DSP Card Slot 1 DSP Card Slot 2

66 Installation Manual

4.2.5 Installing/Removing the Optional Service Cards

2. Insert the screws into the holes on the card, and tighten the screws to secure the card.

Screws

Removing a DSP Card Installed in the DSP Card Slot

1. Loosen and remove the screws.

Screws

Installation Manual 67

4.2.5 Installing/Removing the Optional Service Cards

2. Holding the rear end of the card, pull the card in the direction of the arrows.

68 Installation Manual

4.2.5 Installing/Removing the Optional Service Cards

Installing the Fax Card in the Fax Card Slot

1. Position the FAX card in the FAX card slot. Then, holding the card firmly in place, lower the rear end so

that the holes of the card are aligned with the screw holes.

2. Insert the screws into the holes on the card, and tighten the screws to secure the card.

Screws

Installation Manual 69

4.2.5 Installing/Removing the Optional Service Cards

Removing a Fax Card Installed in the Fax Card Slot

1. Loosen and remove the screws.

Screws

2. Holding the rear end of the card, pull the card in the direction of the arrows.

70 Installation Manual

4.2.5 Installing/Removing the Optional Service Cards

Installing an Optional Service Card in the Free Slot

You can install one of the SLC2/LCOT2, SLC2/BRI4, SLC2/PRI30 or SLC2/PRI23 card. Some of the optional

service cards require DIP switch settings which must be done before installing the card. For details, refer to

the description of each optional service card in "4.5 Physical Trunk and Extension Cards" and "4.6 The

Doorphone Card".

1. Remove the front cover plate for the Free slot.

Screw

Installation Manual 71

4.2.5 Installing/Removing the Optional Service Cards

2. Position the card in the open slot, making sure that the tabs on the both sides of the card fit into place.

Then, holding the card firmly in place, lower the rear end so that the holes of the card are aligned with the

screw holes.

72 Installation Manual

4.2.5 Installing/Removing the Optional Service Cards

3. Insert the screws into the holes on the card, and tighten the screws to secure the card.

Screws

4. Connect cables to appropriate ports of the card. For details about pin assignments, refer to the appropriate

section in "4.5 Physical Trunk and Extension Cards".

Note

Make sure to connect cables after installing the card in the PBX, not before.

Installation Manual 73

4.2.5 Installing/Removing the Optional Service Cards

Removing an Optional Service Card from the Free Slot

1. Loosen and remove the screws.

Screws

2. Holding the rear end of the card, pull the card in the direction of the arrows.

74 Installation Manual

4.2.5 Installing/Removing the Optional Service Cards

Installing the DOORPHONE Card in the Doorphone Slot

1. Remove the front cover plate for the Doorphone Slot.

Screw

Installation Manual 75

4.2.5 Installing/Removing the Optional Service Cards

2. Position the card in the open slot, making sure that the tabs on the both sides of the card fit into place.

Then, holding the card firmly in place, lower the rear end so that the holes of the card are aligned with the

screw holes.

76 Installation Manual

4.2.5 Installing/Removing the Optional Service Cards

3. Insert the screws into the holes on the card, and tighten the screws to secure the card.

Screws

4. Connect cables to appropriate ports of the card. For details about pin assignments, refer to

"4.6.1 DOORPHONE Card (KX-NS0161)" and "4.8 Connecting to a Doorphone, Door Opener, and/or

External Sensor".

Note

Make sure to connect cables after installing the card in the PBX, not before.

Installation Manual 77

4.2.5 Installing/Removing the Optional Service Cards

Removing the DOORPHONE Card from the Doorphone Slot

1. Loosen and remove the screws.

Screws

2. Holding the rear end of the card, pull the card in the direction of the arrows.

78 Installation Manual

4.2.5 Installing/Removing the Optional Service Cards

4.2.6 Installing/Removing the Storage Memory Card

Upgrading from the Initially Installed Storage Memory Card

To increase Voice Mail recording time, you can install an optional Storage Memory Card.

For details about optional Storage Memory Cards, refer to "4.3.2 Storage Memory Card (installed by default),

Storage Memory S Card (KX-NS0135), Storage Memory M Card (KX-NS0136), Storage Memory L Card

(KX-NS0137)".

System Prompts

The Storage Memory Card (installed by default) and optional Storage Memory Cards contain system

prompts for Unified Messaging. However, system prompts language data stored in the Storage Memory

Card (installed by default) differ from those found in the optional Storage Memory Cards.

For information about the system prompt languages in each Storage Memory Card, refer to "7.7 System

Prompt Languages".

The system prompt language data you are using on the initially installed Storage Memory Card must be

backed up if you want to continue using that Storage Memory Card’s system prompt language data. After

backing up the system prompt language data, install the optional Storage Memory Card, and then restore

the backed up system prompt language data to the new Storage Memory Card.

This procedure is described below.

1. Complete Easy Setup Wizard after starting the PBX.

(For details, refer to "5.4.1 Easy Setup Wizard".)

2. Insert a USB memory device into the USB port of the PBX.

(For details, refer to "Using a USB memory device" in "4.9 Connection of Peripherals".)

3. Back up the desired system prompts to the USB memory device.

(For details, refer to "6.9 Tool—UM Data Backup" in the PC Programming Manual.)

4. Shut down the PBX, and then turn the power switch off.

(For details about shutting down the PBX, refer to "5.5 System Control—System Shutdown" in the PC

Programming Manual.)

5. Remove the Storage Memory Card (installed by default), and then install an optional Storage Memory

Card.

(For details, refer to "4.3.2 Storage Memory Card (installed by default), Storage Memory S Card

(KX-NS0135), Storage Memory M Card (KX-NS0136), Storage Memory L Card (KX-NS0137)".)

6. Start the PBX as described in "System Initialisation Procedure" in "4.12 Starting the PBX".

7. Restore the system prompts backed up in step 3. For details, refer to "6.10 Tool—UM Data Restore" in

the PC Programming Manual.

Before Removing the Storage Memory Card

When removing the Storage Memory Card after the PBX has been in use, make a backup of the running system

data so the current data can be restored after installing a new Storage Memory Card. For details about making

backup files, refer to "7.2.2 Utility—File—File Transfer PBX to PC" in the PC Programming Manual.

Backup files cannot be made for some data. For details about which data is not backed up, refer to "Saving

Modified Data" in the PC Programming Manual. For details about restoring Unified Message data from a

backup, refer to "6.10 Tool—UM Data Restore" in the PC Programming Manual.

When you want to back up Unified Messaging system data, a separate backup procedure is required.

For details about backing up Unified Messaging data, refer to "6.9 Tool—UM Data Backup" in the PC

Programming Manual.

CAUTION

• Before touching the product (PBX, cards, etc.), discharge static electricity by touching ground or

wearing an earthing strap. Failure to do so may cause the PBX to malfunction due to static electricity.

• When installing or removing the Storage Memory Card, the power switch must be turned off.

• When installing or removing the Storage Memory Card, do not put pressure on any parts of the mother

board. Doing so may result in damage to the PBX.

Installation Manual 79

4.2.6 Installing/Removing the Storage Memory Card

• The Storage Memory Card contains software for all the processes of the PBX and all the customer

data. Therefore, do not allow unauthorised access to prevent data leakage.

• To prevent data leakage, render the Storage Memory Card physically unusable before disposal.

Notice

• Use only the Storage Memory Card included with the PBX, or a Panasonic optional upgrade Storage

Memory Card.

• The Storage Memory Card must be inserted in the Storage Memory Card slot of the mother board

before startup.

Note

• The is shown on the label of your Storage Memory Card to indicate the direction for inserting the

Storage Memory Card.

• The maximum length of file names for files that are to be stored in the Storage Memory Card is 60

characters.

1. Turn the screw anticlockwise to loosen.

Screw

2. Remove the Storage Memory Card slot cover.

80 Installation Manual

4.2.6 Installing/Removing the Storage Memory Card

3. Remove the Storage Memory Card installed in the slot on the mother board.

4. Insert the new Storage Memory Card into the slot on the mother board.

5. Place the cover as shown below.

Installation Manual 81

4.2.6 Installing/Removing the Storage Memory Card

6. Turn the screw clockwise to tighten.

Screw

82 Installation Manual

4.2.6 Installing/Removing the Storage Memory Card

4.2.7 Types of Connectors

Connector Type Pin Number Used for

RJ45

(Twisted pair cable)

• Mother board

• SLC2/LCOT2 (KX-NS0180)

• SLC2/BRI4 (KX-NS0280)

• SLC2/PRI30 (KX-NS0290CE)

• SLC2/PRI23 (KX-NS0290)

4-pin

Terminal

Block

2-pin

Terminal

Block

• DOORPHONE (KX-NS0161)

RS-232C

9 5

6 1

• Main Unit

(Shielded cable)

Mini Plug

• Mother board

Installation Manual 83

4.2.7 Types of Connectors

4.2.8 Attaching a Ferrite Core

A ferrite core must be attached when an RJ45 connector is connected to the SLC2/PRI30, SLC2/PRI23 or

SLC2/BRI4 card.

For the SLC2/PRI23 and SLC2/PRI30 Cards

For the cable to connect to the ISDN Primary Rate Interface port, wrap the cable once around the ferrite core,

then close the case of the ferrite core. Attach the ferrite core 5 cm away from the connector. The ferrite core

is included with the card.

5 cm

For the SLC2/BRI4 Card

For the cables to connect to the ISDN Basic Rate Interface ports, attach the ferrite cores, then close the cases

of the ferrite cores. Attach the ferrite cores as close to the card’s connectors as possible. The ferrite cores are

included with the card.

When only 1 or 2 cables are used for connection, wrap the

cable(s) once around the ferrite core.

When 3 or more cables are used for connections, wrap up to 2

cables around each ferrite core. All cables should be wrapped

once around the ferrite core it is passing through.

84 Installation Manual

4.2.8 Attaching a Ferrite Core

4.2.9 19-inch Rack Mounting

WARNING

• Be careful not to drop any components. Dropping components may damage them or cause an

injury.

• When mounting the PBX on a 19-inch rack, only use the 19-inch rack mounting equipment

(attachment bracket, screws) included with the PBX.

CAUTION

• When the PBX is mounted on a 19-inch rack, make sure that the installation of the unit does not cause

the temperature of the rack to exceed its limit.

• When the PBX is mounted on a 19-inch rack, do not block the openings of the PBX. Allow space of at

least 10 cm around the PBX’s fan.

• If the PBX is not installed properly using the securing correct methods, the PBX may fall causing serious

damage.

• When this product is no longer in use, make sure to detach it from the rack.

1. Fix the attachment brackets to the left and right sides of the PBX with 3 screws on each side.

(Recommended torque: 0.8 N·m [8.2 kgf·cm] to 1.0 N·m [10.2 kgf·cm])®

2. Place the PBX in the 19-inch rack and fix both attachment brackets to the rack with the rack’s proprietary

mounting equipment. ®

Screw

Attachment Bracket

Installation Manual 85

4.2.9 19-inch Rack Mounting

4.2.10 Placing the PBX on a Desktop

When placing the PBX on a desktop, make sure to follow these instructions.

WARNING

Be careful not to drop any components. Dropping components may damage them or cause an

injury.

CAUTION

• When the PBX is placed on a desktop, make sure that the PBX is placed as indicated in the diagram

below. Do not place it on its side or upside down.

• Do not block the openings of the PBX. Allow space of at least 20 cm above and 10 cm at the sides of

the PBX.

• Make sure that the surface behind the PBX is not made of wood.

Desk or Table

86 Installation Manual

4.2.10 Placing the PBX on a Desktop

4.2.11 Wall Mounting

The PBX can be mounted on a concrete wall using the optional wall mounting kit.

WARNING

• Make sure that the wall that the unit will be attached to is strong enough to support

approximately 4 times the weight of the unit. If not, it is necessary for the wall to be reinforced.

• When mounting the PBX on a wall, only use the wall-mounting equipment (anchor plugs,

screws, metal brackets) included with the PBX and the wall mounting kit.

• Be careful not to drop any components. Dropping components may damage them or cause an

injury.

• Proper earthing (connection to earth) is very important to reduce the risk to the user of

electrocution or to protect the PBX from the bad effects of external noise in the case of a

lightning strike. (See "4.2.4 Frame Earth Connection".)

CAUTION

• Make sure to install all necessary optional service cards in the PBX before performing the wall mounting

procedure. If it is necessary to install or remove a card, make sure to detach the PBX from the wall

before installing or removing the card.

• Do not block the openings of the PBX. Allow space of at least 20 cm above and 10 cm at the sides of

the PBX.

• Make sure that the surface behind the PBX is flat and free of obstacles, so that the openings on the

back of the PBX will not be blocked.

• Make sure that the surface behind the PBX is not made of wood.

• If the PBX is not installed properly using the securing correct methods, the PBX may fall causing serious

damage.

• When placing the PBX onto the wall, make sure that the arrows on the metal brackets are pointing

upward. If the arrows are not pointing upward, the PBX may fall, resulting in injury.

• When driving the screws into the wall, be careful to avoid touching any metal laths, wire laths or plates

in the wall.

• When this unit is no longer in use, make sure to detach it from the wall.

Note

For details about dimensions and weight of the PBX, see "2.3.1 General Description".

Necessary Items

Included in the PBX

Screw B 6

Included in the wall mounting kit (KX-A247)

Top Bracket 1

Bottom Bracket 1

Anchor Plug (For use in concrete) 4

Screw A (For use in concrete) 4

Installation Manual 87

4.2.11 Wall Mounting

Wall Mounting Procedures

1. Measure the actual space as indicated below to mark the 4 screw positions on the wall. Install 4 anchor

plugs in the wall and drive in 4 screws (A) leaving a gap of 5 mm between the screw head and the wall.

Screw (A)

30 mm

8 mm

5 mm

Screw (A)

Hammer

Anchor Plug

Drive the

screw

to this point.

463 mm

87 mm

192 mm

Installation procedure for concrete walls.

Note

• As indicated above, do not tighten the screws fully. You will tighten the screws in step 6.

• The pull-out strength of the installation area must be at least 294 N (30 kgf) per screw.

2. Fix the Top Bracket to the left side of the PBX with 3 screws (B). (Recommended torque: 0.8 N·m

[8.2 kgf·cm] to 1.0 N·m [10.2 kgf·cm])

Screw (B)

3. Fix the Bottom Bracket to the right side of the PBX with 3 screws (B). (Recommended torque: 0.8 N·m

[8.2 kgf·cm] to 1.0 N·m [10.2 kgf·cm])

Screw (B)

88 Installation Manual

4.2.11 Wall Mounting

4. Place the PBX onto the wall, making sure that the guide holes hook onto the screw heads.

CAUTION

When placing the PBX onto the wall, make sure that the arrows on the metal brackets are pointing

upward. If the arrows are not pointing upward, the PBX may fall, resulting in injury. The following

illustrations are bad examples of wall mounting.

Installation Manual 89

4.2.11 Wall Mounting

5. Slide the PBX down into the guide holes.

Guide Hole

6. Fully tighten all 4 screws (A).

Drive the

screw

to this point.

90 Installation Manual

4.2.11 Wall Mounting

4.2.12 Surge Protector Installation

CAUTION

Performing surge protection is essential. Make sure to follow the instructions in this section.

Overview

A massive electrical surge can be caused if lightning strikes a telephone cable 10 m above ground, or if a

telephone line comes into contact with a power line. A surge protector is a device that is connected to a trunk

to prevent potentially dangerous electrical surges from entering the building via the trunk and damaging the

PBX and connected equipment.

To protect the system from electrical surges, we strongly recommend connecting the system to a surge

protector that meets the following specifications:

– Surge arrestor type: 3-electrode arrestor

– DC spark-over voltage: 230 V

– Maximum peak current: at least 10 kA

Additionally, proper earthing is very important for the protection of the system (refer to "4.2.4 Frame Earth

Connection").

Many countries/areas have regulations requiring surge protection. Be sure to comply with all applicable laws,

regulations, and guidelines.

Installation

Trunk TrunkTrunk

Earth

Surge

Protector

Extn.

Extn.: Extension line

SLT

PBX

Frame

Earth

Terminal

Board

Installation Manual 91

4.2.12 Surge Protector Installation

Outside Installation

Trunk

Extn.

Trunk

Surge Protector

Terminal

Board

Surge

Protector

PBX

(Main Building)

Extn.: Extension Line

Extn.

Earth

Extn.

SLT

(Another Building)

SLT

If you install an extension outside of the building, the following precautions are recommended:

a. Install the extension wire underground.

b. Use a conduit to protect the wire.

Note

The surge protector for an extension is different from that for trunks.

Installation of an Earth Rod

Trunk

PBX

Earth Rod

(Underground)

Surge Protector

Earthing

Wire

92 Installation Manual

4.2.12 Surge Protector Installation

1. Connect the earth rod to the surge protector using an earthing wire with a cross-sectional area of at least

1.3 mm

2. Bury the earth rod near the protector. The earthing wire should be as short as possible.

3. The earthing wire should run straight to the earth rod. Do not run the wire around other objects.

4. Bury the earth rod at least 50 cm underground.

Note

• The above figures are recommendations only.

• The length of earth rod and the required depth depend on the composition of the soil.

Installation Manual 93

4.2.12 Surge Protector Installation

4.3 The Mother Board and Expansion Cards

4.3.1 Mother Board

Function

The mother board is the preinstalled processing board with activation keys for CA Basic-Express for

1022 users, use of 8 IP-PT, and 2 Unified Messaging ports. The Virtual Cards (trunk/extension) can be installed

in Virtual Slots of the mother board and can be activated with the activation keys. Also, the mother board

supports LAN connection so that IP telephones (IP-PTs, IP softphones, SIP phones) and PCs can be

connected on a private IP network.

Mountable Cards

• Two of the DSP S, DSP M, or DSP L cards (refer to "4.3.3 DSP S Card (KX-NS0110), DSP M Card

(KX-NS0111), DSP L Card (KX-NS0112)")

• Storage Memory Card (refer to "4.3.2 Storage Memory Card (installed by default), Storage Memory S

Card (KX-NS0135), Storage Memory M Card (KX-NS0136), Storage Memory L Card (KX-NS0137)")

• FAX card (refer to "4.3.4 FAX Card (KX-NS0106)")

• DOORPHONE card (refer to "4.6.1 DOORPHONE Card (KX-NS0161)")

LEDs

Storage Memory Card

Slot Cover

Storage Memory Card Slot

DSP Card Slot

BGM/MOH

Pager

MNT Port

LAN Port

To LAN

To PC

USB Port

LAN Port

WAN Port

LEDs

System Mode Switch

MNT Port

FAX Card Slot

To WA N

WAN Port

Doorphone Slot

The WAN Port is not used with PCMPR Software Version 001.10000.

94 Installation Manual

4.3.1 Mother Board

Note

• Make sure to use the MNT port for PC connection, and the LAN port for LAN connection.

• The maximum length of the CAT 5/CAT 5e cables to be connected to the mother board is 100 m.

• For installing and removing the Storage Memory Card, refer to "4.2.6 Installing/Removing the Storage

Memory Card".

• For details about Virtual Slots, refer to "2.3.3 System Capacity".

• If the preinstalled activation keys on the mother board are not enough for the desired configuration,

you need to purchase activation key codes. For details about the activation keys, refer to

"3.1 Information about the Activation Keys".

• For details about connecting to a LAN, refer to "4.10 LAN Connection".

• For details about connecting peripherals, refer to "4.9 Connection of Peripherals".

• For details about System Mode Switch, refer to "4.12 Starting the PBX".

WARNING

A lithium battery is used in the mother board. There is a risk of explosion if the battery is replaced

with the incorrect type. Dispose of used batteries according to the manufacturer’s instructions.

Pin Assignments

MNT Port/LAN Port/WAN Port

(10BASE-T/100BASE-TX)

No.

Signal Name Input (I)/Output (O) Function

1 TPO+ O Transmit data+

2 TPO- O Transmit data-

3 TPI+ I Receive data+

4-5 Reserved – –

6 TPI- I Receive data-

7-8 Reserved – –

MNT Port/LAN Port/WAN Port

(1000BASE-T)

No. Signal Name

Input (I)/

Output (O)

Function

1 TRD0 (+) I/O Transmit and receive data 0 (+)

2 TRD0 (-) I/O Transmit and receive data 0 (-)

3 TRD1 (+) I/O Transmit and receive data 1 (+)

4 TRD2 (+) I/O Transmit and receive data 2 (+)

5 TRD2 (-) I/O Transmit and receive data 2 (-)

6 TRD1 (-) I/O Transmit and receive data 1 (-)

7 TRD3 (+) I/O Transmit and receive data 3 (+)

8 TRD3 (-) I/O Transmit and receive data 3 (-)

The WAN Port is not used with PCMPR Software Version 001.10000.

Installation Manual 95

4.3.1 Mother Board

LED Indications

Indication Colour Description

STATUS Green PBX status indication

• OFF: Power Off

• ON: Power On and running

• Flashing: Starting up/Logging in

Amber PBX status indication

• ON: Ready to shutdown

• Flashing: Shutting down

Red PBX status indication

• ON: Alarm (CPU stop, no IP address[es]

assigned for the DSP card[s] by the DHCP

server, alarm for each optional service card)

• Flashing: Initialise failed

BATT ALARM Red Alarm indication

• OFF: Normal

• ON: Alarm

MASTER Green Master/Slave unit status indication

• ON: Master

Amber Master/Slave unit status indication

• ON: Slave

• Flashing: Factory default

10BASE-T/

100BASE-TX/

1000BASE-T

MNT LINK Green Link status indication

• OFF: Off-line

• ON: Linked normally

• Flashing: In communication

1000 Green/

Yellow

Data transmission speed indication

• OFF: 10 Mbps

• Yellow ON: 100 Mbps

• Green ON: 1000 Mbps

LAN LINK Green Link status indication

• OFF: Off-line

• ON: Linked normally

• Flashing: In communication

1000 Green/

Yellow

Data transmission speed indication

• OFF: 10 Mbps

• Yellow ON: 100 Mbps

• Green ON: 1000 Mbps

96 Installation Manual

4.3.1 Mother Board

Indication Colour Description

WAN

LINK Green Link status indication

• OFF: Off-line

• ON: Linked normally

• Flashing: In communication

1000 Green/

Yellow

Data transmission speed indication

• OFF: 10 Mbps

• Yellow ON: 100 Mbps

• Green ON: 1000 Mbps

The WAN Port is not used with PCMPR Software Version 001.10000.

Installation Manual 97

4.3.1 Mother Board

4.3.2 Storage Memory Card (installed by default), Storage Memory

S Card (KX-NS0135), Storage Memory M Card (KX-NS0136),

Storage Memory L Card (KX-NS0137)

Function

Storage Memory Card

(Installed by default):

Storage Memory with 2 hours Voice Mail recording time. To increase

recording time to a maximum of 15 hours, activate REC Time Expansion

(KX-NSU001) activation key.

Storage Memory S: Storage Memory with maximum of 200 hours Voice Mail recording time.

Storage Memory M: Storage Memory with maximum of 450 hours Voice Mail recording time.

Storage Memory L: Storage Memory with maximum of 1000 hours Voice Mail recording time.

Storage Memory Card

Storage Memory Card Slot

Mother Board

Accessories and User-supplied Items

Accessories (included): none

User-supplied (not included): none

Note

For installing and removing the Storage Memory Card, refer to "4.2.6 Installing/Removing the Storage

Memory Card".

98 Installation Manual

4.3.2 Storage Memory Card (installed by default), Storage Memory S Card (KX-NS0135), Storage Memory M Card (KX-

NS0136), Storage Memory L Card (KX-NS0137)

4.3.3 DSP S Card (KX-NS0110), DSP M Card (KX-NS0111), DSP L

Card (KX-NS0112)

Function

A DSP card is a digital signal processor card with DSP resources that can be used for VoIP calls, conferences,

the Unified Messaging feature, and the DISA/OGM feature. The DSP cards are compliant with ITU-T G.

729A and G.711 codec methods.

Depending on the amount of your DSP resource needs, DSP S, DSP M, or DSP L cards can be installed. Up

to 2 DSP cards can be installed on the mother board.

To operate the PBX, at least one DSP S, DSP M, or DSP L card must be installed in one of the DSP card slots.

inside

DSP Card

Screws

DSP Card

inside

DSP Card Slot 2DSP Card Slot 1

Accessories and User-supplied Items

Accessories (included): Screws ´ 3

User-supplied (not included): none

CAUTION

When installing or removing optional service cards, do not put pressure on any parts of the mother board.

Doing so may result in damage to the PBX.

Note

The DSP Resource Advisor can be used to calculate DSP resource usage easily. For details, refer to

"9.32.1.1 PBX Configuration—Configuration—DSP Resource—Setting—DSP Resource Advisor" in the

PC Programming Manual.

DSP Resource Information

The number of resources provided by each type of DSP card is as follows:

DSP Card Type

Number of Resources

DSP S 63

Installation Manual 99

4.3.3 DSP S Card (KX-NS0110), DSP M Card (KX-NS0111), DSP L Card (KX-NS0112)

DSP Card Type Number of Resources

DSP M 127

DSP L 254

IP Address Information

Either 1 or 2 IP addresses must be assigned to each DSP card, depending on the type of DSP card. You can

assign IP addresses to the DSP cards during Easy Setup Wizard or through system programming.

For details about Easy Setup Wizard, refer to "5.4.1 Easy Setup Wizard".

For details about assigning IP addresses through System Programming, refer to "Changing IP Address

Settings".

DSP Card Type

Number of IP Addresses

DSP S/DSP M 1

DSP L 2

100 Installation Manual

4.3.3 DSP S Card (KX-NS0110), DSP M Card (KX-NS0111), DSP L Card (KX-NS0112)

4.3.4 FAX Card (KX-NS0106)

Function

1-channel fax server. To be mounted on the mother board.

FAX Card

Screws

inside

Accessories and User-supplied Items

Accessories (included): Screws ´ 3

User-supplied (not included): none

Note

When installing or removing the FAX card, do not put pressure on any parts of the mother board. Doing

so may result in damage to the PBX.

Installation Manual 101

4.3.4 FAX Card (KX-NS0106)

4.4 Virtual Cards

Function

Virtual Cards are programs included with the mother board and that are treated as virtual cards by Web

Maintenance Console for convenience. Those programs can be activated with the appropriate activation key

(apart from V-IPCS4 cards, which do not require activation keys). By installing Virtual Cards in the Virtual Slots

of the mother board using Web Maintenance Console, IP trunks, IP extensions, and IP-CSs can be used via

the mother board.

Virtual Card

Description

Virtual 16-Channel SIP Trunk Card

(V-SIPGW16)

Virtual Card for 16-channel SIP trunk. Compliant with RFC

3261, 3262, 3264, 3311, 3581, 3960 and 4028 protocols, and

ITU-T G.729A and G.711 codec methods. Also supports T.38

protocol.

Virtual 16-Channel VoIP Gateway

Card (V-IPGW16)

Virtual Card for 16-channel H.323 trunk. Compliant with VoIP

H.323 V.5 protocol, and ITU-T G.729A and G.711 codec

methods. Also supports T.38 protocol.

Virtual 32-Channel VoIP Extension

Card (V-IPEXT32)

Virtual Card for 32 IP-PTs (KX-NT300 series and KX-NT265

[software version 2.00 or later only]). Compliant with Panasonic

proprietary protocol, and ITU-T G.729A, G.711 and G.722

codec methods.

Virtual 32-Channel SIP Extension

Card (V-SIPEXT32)

Virtual Card for 32 third party SIP phones. Compliant with RFC

3261, 3264, 3310, 2327 and 4028 protocols, and ITU-T G.

729A, G.711 and G.722 codec methods.

Virtual 4 IP Cell Station Interface Card

(V-IPCS4)

Virtual Card for 4 IP-CSs. Compliant with ITU-T G.729A and

G.711 codec methods.

Virtual UT Extension Card

(V-UTEXT32)

Virtual Card for 32 KX-UT series SIP phones. Compliant with

RFC 2327, 3261, 3264, 3310, 3515, 4028 and 4235 protocols,

and ITU-T G.729A, G.711 and G.722 codec methods. Also

supports WSD, CWMP and HTTP.

102 Installation Manual

4.4 Virtual Cards

Example: Virtual Cards in the Virtual Slots of the PBX

Mother Board

V-IPGW16 V-IPEXT32 V-SIPEXT32 V-IPCS4

V-UTEXT32

V-SIPGW16

V-IPEXT32 V-SIPEXT32 V-IPCS4 V-UTEXT32V-IPGW16

V-SIPGW16

V-IPGW16 V-SIPEXT32 V-IPCS4 V-UTEXT32V-IPEXT32

V-SIPGW16

V-IPGW16 V-UTEXT32

V-SIPGW16

V-IPEXT32 V-SIPEXT32 V-IPCS4

Virtual Slots

Installation Manual 103

4.4 Virtual Cards

4.5 Physical Trunk and Extension Cards

4.5.1 SLC2/LCOT2 Card (KX-NS0180)

Function

A combination card including:

• 2 analogue trunk ports with Caller ID (FSK/FSK with Call Waiting Caller ID [Visual Caller ID]/DTMF). One

port is a power failure transfer (PFT) port.

• 2 extension ports with Caller ID (FSK) for SLTs.

To trunk

To SLT

RJ45

Accessories and User-supplied Items

Accessories (included): Screws ´ 4

User-supplied (not included): RJ45 connector, Twisted pair cable

Note

• For details about power failure transfer, refer to "4.11 Power Failure Ports".

• To confirm the trunk connection, refer to "Confirming the Trunk Connection" in "4.12 Starting the

PBX".

Pin Assignments

RJ45 Connector for Trunk Use

No.

Signal Name Function

1 8

R T

1-3 Reserved –

4 R Ring

5 T Tip

6-8 Reserved –

104 Installation Manual

4.5.1 SLC2/LCOT2 Card (KX-NS0180)

RJ45 Connector for Single Line Telephone Extension Use

No. Signal Name Function

1 8

RA TA

1-2 Reserved –

3 RB Ring B

4 RA Ring A

5 TA Tip A

6 TB Tip B

7-8 Reserved –

Installation Manual 105

4.5.1 SLC2/LCOT2 Card (KX-NS0180)

4.5.2 SLC2/BRI4 Card (KX-NS0280)

Function

A combination card including:

• 4 ISDN Basic Rate Interface ports.

• 2 extension ports with Caller ID (FSK) for SLTs.

EURO-ISDN/ETSI compliant.

LEDs

To NT1/

Extension

To SLT

RJ45

(LINE 1 to LINE 4)

RJ45 for SLT

Accessories and User-supplied Items

Accessories (included): Ferrite core ´ 2, Screws ´ 4

User-supplied (not included): RJ45 connector, Twisted pair cable

CAUTION

When connecting this optional service card to the trunk, connect through an NT1; do not connect to the U

interface of the trunk directly.

Notice

When connecting the RJ45 connector, attach the included ferrite core. Refer to "4.2.8 Attaching a Ferrite

Core".

Note

• This optional service card has 100 W of terminal resistance. For use in point to multi-point connection,

the card must be placed at the end of the bus.

• This optional service card can be used for either trunk or extension connection, by setting the A/B

switch or using the connector with appropriate pin assignments.

• To confirm the trunk connection, refer to "Confirming the Trunk Connection" in "4.12 Starting the

PBX".

Switch Settings

Switch

Type Usage and Status Definition

A/B Slide Select A (default) for trunk or B for extension use.

106 Installation Manual

4.5.2 SLC2/BRI4 Card (KX-NS0280)

Pin Assignments

RJ45 Connector for Trunk Use

No. Signal Name Level [V] Function

1-2 Reserved – –

3 TX1 (+) Transmit data 1

4 RX1 (+) Receive data 1

5 RX2 (-) Receive data 2

6 TX2 (-) Transmit data 2

7-8 Reserved – –

RJ45 Connector for Extension Use

No.

Signal Name Level [V] Function

1-2 Reserved – –

3 RX1 (+) Receive data 1

4 TX1 (+) Transmit data 1

5 TX2 (-) Transmit data 2

6 RX2 (-) Receive data 2

7-8 Reserved – –

RJ45 Connector for Single Line Telephone Extension Use

No.

Signal Name Function

1 8

RA TA

1-2 Reserved –

3 RB Ring B

4 RA Ring A

5 TA Tip A

6 TB Tip B

7-8 Reserved –

LED Indications

Indication

Colour Description

LINE 4

LINE 3

LINE 2

LINE 1

Green Line status indication (LINE 1 to LINE 4):

Refer to "LINE LED Pattern" below for details.

Installation Manual 107

4.5.2 SLC2/BRI4 Card (KX-NS0280)

LINE LED Pattern

Layer 1 Layer 2

Master

Clock

LED Pattern

OFF OFF OFF

1 s

ON OFF OFF

1 s

ON ON OFF

1 s

ON OFF ON

1 s

ON ON ON

1 s

Layer 1: ON (Synchronous)

Layer 2: ON (Link established)/OFF (Link not established)

Master Clock: ON (Master)/OFF (Slave)

Maximum Cabling Distance of ISDN DSU Connection

The maximum length of the cable that connects the DSU and the PBX is shown below:

CAT 5: Under 1000 m

DSU

Point-to-Point

108 Installation Manual

4.5.2 SLC2/BRI4 Card (KX-NS0280)

Maximum Cabling Distance of ISDN Terminal Equipment (TE) Connection

The maximum length of the extension cable that connects the PBX and the TE is shown below:

CAT 5: Under 1000 m

Point-to-Point

Installation Manual 109

4.5.2 SLC2/BRI4 Card (KX-NS0280)

4.5.3 SLC2/PRI30 Card (KX-NS0290CE)

Function

A combination card including:

• 1 ISDN Primary Rate Interface port (30B channels).

• 2 extension ports with Caller ID (FSK) for SLTs.

EURO-ISDN/ETSI compliant.

LEDs

To NT1/

Extension

To SLT

LEDs

RJ45

Accessories and User-supplied Items

Accessories (included): Ferrite core ´ 1, Screws ´ 4

User-supplied (not included): RJ45 connector, Twisted pair cable

CAUTION

• When connecting this optional service card to the trunk, connect through an NT1; do not connect to

the U interface of the trunk directly.

• PRI ports are SELV ports and should only be connected to SELV services.

Notice

• When connecting the RJ45 connector, attach the included ferrite core. Refer to "4.2.8 Attaching a

Ferrite Core".

• The cable to connect to the ISDN Primary Rate Interface port of the SLC2/PRI30 card should be

CAT 5 (Category 5) or higher.

Note

• In some countries/areas, this optional service card must not be connected to the Public Switched

Telephone Network.

• This optional service card can be used for either trunk or extension connection, by setting the A/B

switch or using the connector with appropriate pin assignments.

• To confirm the trunk connection, refer to "Confirming the Trunk Connection" in "4.12 Starting the

PBX".

Switch Settings

Switch

Type Usage and Status Definition

A/B Slide Select A (default) for trunk or B for extension use.

110 Installation Manual

4.5.3 SLC2/PRI30 Card (KX-NS0290CE)

Pin Assignments

RJ45 Connector for Trunk Use

No. Signal Name Level [V] Function

1 RX+ (+) Receive data (+)

2 RX- (-) Receive data (-)

3 Reserved – –

4 TX- (-) Transmit data (-)

5 TX+ (+) Transmit data (+)

6-8 Reserved – –

RJ45 Connector for Extension Use

No.

Signal Name Level [V] Function

1 TX- (-) Transmit data (-)

2 TX+ (+) Transmit data (+)

3 Reserved – –

4 RX+ (+) Receive data (+)

5 RX- (-) Receive data (-)

6-8 Reserved – –

RJ45 Connector for Single Line Telephone Extension Use

No.

Signal Name Function

1 8

RA TA

1-2 Reserved –

3 RB Ring B

4 RA Ring A

5 TA Tip A

6 TB Tip B

7-8 Reserved –

LED Indications

Indication

Colour Description

SERR Red Non-synchronisation status indication

• OFF: Normal

• ON: Out of synchronisation

Installation Manual 111

4.5.3 SLC2/PRI30 Card (KX-NS0290CE)

Indication Colour Description

RAI Red RAI signal status indication

• OFF: Normal

• ON: Alarm

• Flashing (60 times per minute): Alarm (Clock Master)

AIS Red AIS status indication

• OFF: Normal

• ON: Alarm

SYNC Green Synchronisation status indication

• OFF: Not synchronised

• ON: Synchronised

• Flashing (60 times per minute): Synchronised (External Clock

Master)

DLK Green Data link status indication

• OFF: Not established

• ON: Established

Maximum Cabling Distance of Extension Connection

The maximum length of the extension cable that connects the PRI port is shown below:

CAT 5: Under 200 m

112 Installation Manual

4.5.3 SLC2/PRI30 Card (KX-NS0290CE)

4.5.4 SLC2/PRI23 Card (KX-NS0290)

Function

A combination card including:

• 1 ISDN Primary Rate Interface port (23B channels).

• 2 extension ports with Caller ID (FSK) for SLTs.

NI (North American standard ISDN protocol) compliant.

LEDs

RJ45

To NT1/

Extension

To SLT

Accessories and User-supplied Items

Accessories (included): Ferrite core ´ 1, Screws ´ 4

User-supplied (not included): RJ45 connector, Twisted pair cable

CAUTION

• When connecting this optional service card to the trunk, connect through an NT1; do not connect to

the U interface of the trunk directly.

• PRI ports are SELV ports and should only be connected to SELV services.

Notice

• When connecting the RJ45 connector, attach the included ferrite core. Refer to "4.2.8 Attaching a

Ferrite Core".

• The cable to connect to the ISDN Primary Rate Interface port of the SLC2/PRI23 card should be

CAT 5 (Category 5) or higher.

Note

• This optional service card can be used for either trunk or extension connection, by setting the A/B

switch or using the connector with appropriate pin assignments.

• To confirm the trunk connection, refer to "Confirming the Trunk Connection" in "4.12 Starting the

PBX".

Switch Settings

Switch

Type Usage and Status Definition

A/B Slide Select A (default) for trunk or B for extension use.

Installation Manual 113

4.5.4 SLC2/PRI23 Card (KX-NS0290)

Pin Assignments

RJ45 Connector for Trunk Use

No. Signal Name Level [V] Function

1 RX+ (+) Receive data (+)

2 RX- (-) Receive data (-)

3 Reserved – –

4 TX- (-) Transmit data (-)

5 TX+ (+) Transmit data (+)

6-8 Reserved – –

RJ45 Connector for Extension Use

No.

Signal Name Level [V] Function

1 TX- (-) Transmit data (-)

2 TX+ (+) Transmit data (+)

3 Reserved – –

4 RX+ (+) Receive data (+)

5 RX- (-) Receive data (-)

6-8 Reserved – –

RJ45 Connector for Single Line Telephone Extension Use

No.

Signal Name Function

1 8

RA TA

1-2 Reserved –

3 RB Ring B

4 RA Ring A

5 TA Tip A

6 TB Tip B

7-8 Reserved –

LED Indications

Indication

Colour Description

SERR Red Non-synchronisation status indication

• OFF: Normal

• ON: Out of synchronisation

114 Installation Manual

4.5.4 SLC2/PRI23 Card (KX-NS0290)

Indication Colour Description

RAI Red RAI signal status indication

• OFF: Normal

• ON: Alarm (Clock Slave)

• Flashing (60 times per minute): Alarm (Clock Master)

AIS Red AIS status indication

• OFF: Normal

• ON: Alarm

SYNC Green Synchronisation status indication

• OFF: Not synchronised

• ON: Synchronised

• Flashing (60 times per minute): Synchronised (External Clock

Master)

DLK Green Data link status indication

• OFF: Not established

• ON: Established

Maximum Cabling Distance of Extension Connection

The maximum length of the extension cable that connects the PRI port is shown below:

CAT 5: Under 200 m

Installation Manual 115

4.5.4 SLC2/PRI23 Card (KX-NS0290)

4.6 The Doorphone Card

4.6.1 DOORPHONE Card (KX-NS0161)

Function

A doorphone card for 1 doorphone, 1 door opener, and 1 external sensor.

To door opener

To doorphone/

external sensor

4-pin 2-pin

Accessories and User-supplied Items

Accessories (included): Screws ´ 2

User-supplied (not included): Copper wire

Note

For details about connecting to a doorphone and/or door opener, refer to "4.8 Connecting to a Doorphone,

Door Opener, and/or External Sensor".

Pin Assignments

4-pin Terminal Block

No.

Signal Name Function

1 SENS1b Sensor 1 common

2 SENS1a Sensor 1

3 COM1 Doorphone 1 receive

4 DP1 Doorphone 1 transmit

2-pin Terminal Block

No.

Signal Name Function

1 OP1b Door opener 1 (Relay)

2 OP1a Door opener 1 com (Relay com)

116 Installation Manual

4.6.1 DOORPHONE Card (KX-NS0161)

External Sensor

Power to the external sensor is provided from the DOORPHONE card and must be grounded through the

DOORPHONE card as indicated in the diagram below. A pair of "sensor" and "common" lines are connected

to the DOORPHONE card for each external sensor. The PBX detects input from the sensor when the signal

is under 100 W.

Connection Diagram

External Sensor

sensor

common

I/O

DOORPHONE

PBX

+3.3V

10K

4.7K

Door Opener

Current Limit: 24 V DC/30 V AC, 1 A maximum

Connecting to the DOORPHONE Card

When connecting a doorphone, door opener, and/or external sensor to the DOORPHONE card, use copper

wire with a diameter from 0.42 mm to 1.12 mm. Follow the procedure below to connect a doorphone, door

opener, and/or external sensor to the DOORPHONE card.

1. Strip off the insulation of the wire about 10 mm from the end.

2. Use a screwdriver to press on the orange tab at the bottom of the terminal block, and insert the wire into

the upper hole.

3. Check from side to ensure that no bare copper wire is exposed.

10 mm

Copper Wire

DOORPHONE Card

(ø 0.42 mm to 1.12 mm)

Installation Manual 117

4.6.1 DOORPHONE Card (KX-NS0161)

4.7 Connection of SLTs

4.7.1 Maximum Cabling Distances of the Extension Wiring

(Twisted Cable)

Cable Maximum Distance

ø 0.4 mm:

698 m

ø 0.5 mm:

1128 m

ø 0.6 mm:

1798 m

CAT 5:

1128 m

SLT

Notice

The maximum cabling distance may vary depending on the conditions.

118 Installation Manual

4.7.1 Maximum Cabling Distances of the Extension Wiring (Twisted Cable)

4.8 Connecting to a Doorphone, Door Opener, and/

or External Sensor

The PBX supports 1 each of a doorphone, a door opener, and an external sensor.

Note

Doorphones, door openers, and external sensors are user-supplied.

Maximum Cabling Distance

Doorphone

Door Opener

Cable Maximum Distance

ø 0.42 mm: 70 m

ø 0.5 mm: 113 m

ø 0.6 mm: 180 m

CAT 5: 113 m

External Sensor

Installing the Doorphone (KX-T30865/KX-T7765)

Note

The illustrations shown in the installation procedure are based on the KX-T30865.

1. Loosen the screw to separate the doorphone into 2 halves.

Panasonic

Screw

Installation Manual 119

4.8 Connecting to a Doorphone, Door Opener, and/or External Sensor

Note for KX-T7765 Users

When loosening/tightening the screw, do not scratch the cabinet wall with the driver shaft.

Cabinet Wall

2. Pass the wires through the hole in the base cover, and attach the base cover to a wall using 2 screws.

Screw

To 4-pin terminal block

Note

Two kinds of screws are included with the doorphone. Please choose the appropriate kind for your wall

type.

: when a doorphone plate has been fixed to the wall

: when you wish to install the doorphone directly onto the wall

3. Connect the wires to the screws located in the back cover.

To 4-pin terminal block

4. Re-attach the 2 halves and re-insert the screw.

120 Installation Manual

4.8 Connecting to a Doorphone, Door Opener, and/or External Sensor

Connection

Use 4-pin and 2-pin terminal blocks (included with the card) for connection.

1. While pressing on the orange tab at the bottom of the terminal block using a screwdriver, insert the wire

into the upper hole as shown below. Repeat this procedure for each doorphone, door opener, and/or

external sensor wire to connect.

Refer to "4.6.1 DOORPHONE Card (KX-NS0161)" for pin assignments.

For information about wiring, refer to "Connecting to the DOORPHONE Card".

Doorphone

Door Opener

External Sensor

Installation Manual 121

4.8 Connecting to a Doorphone, Door Opener, and/or External Sensor

4.9 Connection of Peripherals

Cable Maximum Distance

Maximum Distance

Cable Maximum Distance

Maximum Distance

BGM

Music on Hold

Pager:

Amplifier/Speaker

Printer

ø 0.4 mm: 10 m

ø 0.5 mm: 10 m

ø 0.6 mm: 10 m

CAT 5/

CAT 5e:

10 m

100 m

ø 0.4 mm: 10 m

ø 0.5 mm: 10 m

ø 0.6 mm: 10 m

CAT 5/

CAT 5e:

10 m

2 m

Back

MNT Port

RS-232C

UPS

USB Port

Maximum Distance

5 m

USB Memory

Device

PC (via MNT Port)

A PC can be connected to the PBX via the MNT port of the PBX. It is used for system programming, diagnostics

and external system database storage (save/load) functions.

Pin Assignments for 10BASE-T/100BASE-TX

No.

Signal Name Input (I)/Output (O) Function

1 TPO+ O Transmit data+

2 TPO- O Transmit data-

3 TPI+ I Receive data+

4-5 Reserved – –

6 TPI- I Receive data-

7-8 Reserved – –

122 Installation Manual

4.9 Connection of Peripherals

Pin Assignments for 1000BASE-T

No. Signal Name

Input (I)/

Output (O)

Function

1 TRD0 (+) I/O Transmit and receive data 0 (+)

2 TRD0 (-) I/O Transmit and receive data 0 (-)

3 TRD1 (+) I/O Transmit and receive data 1 (+)

4 TRD2 (+) I/O Transmit and receive data 2 (+)

5 TRD2 (-) I/O Transmit and receive data 2 (-)

6 TRD1 (-) I/O Transmit and receive data 1 (-)

7 TRD3 (+) I/O Transmit and receive data 3 (+)

8 TRD3 (-) I/O Transmit and receive data 3 (-)

Note

You can use 1000BASE-T cables for 10BASE-T/100BASE-TX connections.

BGM/MOH

The PBX provides Background Music and Music on Hold. An external music source (e.g., user-supplied radio)

can be connected to the PBX.

CAUTION

The MOH port is an SELV port and should only be connected to an approved SELV device, or in Australia,

via a Line Isolation Unit with a Telecommunications Compliance Label.

Notice

• Wiring should be done carefully to prevent undue force being exerted on the plug. Otherwise, sound

may only be heard intermittently.

• When the PBX and external music source are not connected to the same earth, hum noise may be

induced into Background Music and Music on Hold.

Pager

A paging device (user-supplied) can be connected to the PBX.

CAUTION

The Pager port is an SELV port and should only be connected to an approved SELV device, or in Australia,

via a Line Isolation Unit with a Telecommunications Compliance Label.

PC/Printer (via RS-232C)

The PBX is equipped with an RS-232C interface. This interface provides communication between the PBX

and the user-supplied devices such as PC or line printers. The RS-232C port is used for SMDR, diagnostics

and external system database storage (save/load) functions.

CAUTION

To protect the system, keep the following in mind:

Installation Manual 123

4.9 Connection of Peripherals

1. Make sure that both connector cases (frame ground) of the RS-232C cross cable (shielded cable) are

conductive. If they are not conductive, make sure that both connector cases of the cable are firmly

connected.

2. If this is not possible, connect the frame of the PBX to the frame of the PC/Printer using an earthing

wire in order to prevent difference in the electrical potentials.

Pin Assignments

No. Signal Name Function

Circuit Type

EIA CCITT

9 5

6 1

2 RD (RXD) Receive Data BB 104

SD (TXD)

ER (DTR)

Transmit Data

Data Terminal Ready

103

108.2

DR (DSR)

Signal Ground

Data Set Ready

102

107

RS (RTS)

CS (CTS)

Request To Send

Clear To Send

105

106

Connection Charts

For connecting a printer/PC with a 9-pin RS-232C connector

Printer/PC (9-pin)

Circuit Type

(EIA)

Signal

Name

RD (RXD)

SD (TXD)

ER (DTR)

DR (DSR)

RS (RTS)

CS (CTS)

Pin No.

PBX (9-pin)

Signal

Name

Pin No.

RD (RXD) 2

SD (TXD) 3

ER (DTR) 4

SG 5

DR (DSR) 6

RS (RTS) 7

CS (CTS) 8

Circuit Type

(EIA)

124 Installation Manual

4.9 Connection of Peripherals

For connecting a printer/PC with a 25-pin RS-232C connector

Printer/PC (25-pin)

Signal

Name

Circuit Type

(EIA)

1FG AA

3 RD (RXD) BB

2 SD (TXD) BA

ER (DTR) CD

SG AB

5 CS (CTS) CB

DR (DSR) CC

4 RS (RTS)

Pin No.

PBX (9-pin)

Circuit Type

(EIA)

Signal

Name

Pin No.

BB RD (RXD) 2

BA SD (TXD) 3

CD ER (DTR) 4

SG 5

DR (DSR) 6

CA RS (RTS) 7

CS (CTS) 8

RS-232C Signals

• Receive Data (RXD):…(input)

Conveys signals from the printer or the PC.

• Transmit Data (TXD):…(output)

Conveys signals from the unit to the printer or the PC. A "Mark" condition is held unless data or BREAK

signals are being transmitted.

• Data Terminal Ready (DTR):…(output)

This signal line is turned ON by the unit to indicate that it is ON LINE. Circuit ER (DTR) ON does not indicate

that communication has been established with the printer or the PC. It is switched OFF when the unit is

OFF LINE.

• Signal Ground (SG)

Connects to the DC ground of the unit for all interface signals.

• Data Set Ready (DSR):…(input)

An ON condition of circuit DR (DSR) indicates the printer or the PC is ready. Circuit DR (DSR) ON does

not indicate that communication has been established with the printer or the PC.

• Request To Send (RTS):…(output)

This lead is held ON whenever DR (DSR) is ON.

• Clear To Send (CTS):…(input)

An ON condition of circuit CS (CTS) indicates that the printer or the PC is ready to receive data from the

unit. The unit does not attempt to transfer data or receive data when circuit CS (CTS) is OFF.

• Frame Ground (FG)

Connects to the unit frame and the earth ground conductor of the AC power cord.

USB Interface for Uninterruptible Power Supply (UPS) and USB Memory

Device

The PBX is equipped with a USB 2.0 interface. This interface provides communication between the PBX and

user-supplied devices such as a UPS or USB memory device.

Using a USB memory device

A USB memory device can be used to backup and restore the system data of the PBX.

The PBX supports USB memory devices that meet the following specifications:

• File system: FAT

• Maximum capacity: 32 GB

Installation Manual 125

4.9 Connection of Peripherals

• Maximum current: 500 mA

For details about backing up and restoring using a USB memory device, refer to "6.1 Tool—System Data

Backup to USB" in the PC Programming Manual.

Note

Do not use a USB hub when connecting a USB memory device to the PBX.

Using a UPS

A UPS is a device that supplies power for several minutes to a connected device when a power failure occurs.

For details about connecting a UPS to the PBX, refer to "Connecting an Uninterruptible Power Supply

(UPS)".

Note

When connecting a UPS, use only the USB cable included with the UPS, and do not use a USB hub.

126 Installation Manual

4.9 Connection of Peripherals

4.10 LAN Connection

4.10.1 LAN Connection for the Main Unit

Connecting the Main Unit to the LAN

The PBX is equipped with a LAN port for connecting to a LAN so that IP telephones (IP-PTs, IP softphones,

SIP phones), IP-CSs, PCs and a CTI Server can be connected on a private IP network. When the PBX is

connected to the LAN for the first time, you must assign IP addressing information to the PBX. See

"5.4 Programming the PBX" for instructions.

TX+

TX-

RX+

RX-

RX+

RX-

TX+

TX-

CTI Server

IP-PT

Switching Hub

IP Softphone,

CA Client PC

Switching Hub PBX (LAN Port)

Pin No.

Signal Name Signal Name

Pin No.

LAN Port

SIP Phone

IP-CS

Connection for 10BASE-T/100BASE-TX

Ethernet Cable

Installation Manual 127

4.10.1 LAN Connection for the Main Unit

TRD0 (+)

TRD0 (-)

TRD1 (+)

TRD2 (+)

Switching Hub PBX (LAN Port)

Pin No.

Signal Name Signal Name

Pin No.

Connection for 1000BASE-T

TRD2 (-)

TRD1 (-)

TRD3 (+)

TRD3 (-)

TRD0 (+)

TRD0 (-)

TRD1 (+)

TRD2 (+)

TRD2 (-)

TRD1 (-)

TRD3 (+)

TRD3 (-)

Note

• Use an Ethernet cable with an RJ45 connector for connection to a switching hub. The cable should be

a CAT 5 (Category 5) or higher for 10BASE-T/100BASE-TX, or CAT 5e (Enhanced Category 5) or

higher for 1000BASE-T.

• Make sure that all CAT 5/CAT 5e cables in use are not over 100 m in length.

• Make sure to set the port of the switching hub that connects to the card to operate under "Auto

Negotiation" mode.

• Make sure to create a spanning tree for LAN connection in order to prevent loops from occurring in a

multi-bridged environment. Otherwise, some packets may circulate for long periods of time and

eventually PBX performance system may degrade.

• The CTI server can be used for connecting PCs on a LAN to provide third party call control CTI.

CTI connection uses the CSTA Phase 3 or TAPI 2.1 protocol. The operating system of the PC or CTI

server required for third party call control depends on your CTI application software. For details, refer

to the manual for your CTI application software.

• When using the VLAN feature on the network, make sure that the PBX is connected to a layer 2 switch

that is IEEE 802.1Q compliant, and that is configured for VLANs. In addition, the port of the switching

hub to which the PBX is connected must be set to "Untagged". Consult your network administrator for

details.

128 Installation Manual

4.10.1 LAN Connection for the Main Unit

4.10.2 LAN Connections for IP Telephones

When an IP telephone is connected to the LAN and power is supplied for the first time, you will be prompted

to set network parameters. The network parameters must be set for the IP telephone before it can be used.

Refer to "5.8 Assigning Networking Information to IP Telephones" for instructions.

Connecting an IP Telephone to a Switching Hub

When connecting an IP telephone to the LAN, connect it to a switching hub.

Note

• Use an Ethernet straight cable with an RJ45 connector to connect the IP telephone to a switching hub.

The cable should be a CAT 5 (Category 5) or higher for 10BASE-T/100BASE-TX, or CAT 5e (Enhanced

Category 5) or higher for 1000BASE-T.

• When using the VLAN feature on the network, make sure that the switching hub to be connected is

IEEE 802.1Q compliant and is configured for VLANs. In addition, the port of a switching hub that the

IP telephone is connected to must be set to "Trunk" port, to allow VLAN tagging. Consult your network

administrator for details.

• Since an IP softphone is installed and operates on a PC, the PC must be connected to the LAN to use

the IP softphone on the network.

The diagram below is for connecting an IP-PT to a switching hub. For SIP phones, refer to the documentation

of your SIP phone.

Example: KX-NT346

Ethernet Straight Cable

To a Switching Hub

Installation Manual 129

4.10.2 LAN Connections for IP Telephones

Connecting an AC Adaptor to an IP Telephone

IP-PTs and some SIP phones comply with the IEEE 802.3af Power-over-Ethernet (PoE) standard. If PoE is

available on your network, these IP telephones can receive the necessary power supply from the network

through the network cable. In this case, no AC adaptor is needed for the IP telephones.

However, if PoE is not available, you will need to connect an AC adaptor to the IP telephone.

Note

Use only the specified type of AC adaptor for each IP telephone. For details, refer to the documentation of

your IP telephone.

Example: KX-NT346

AC Adaptor Cord

To Wall Socket

Connecting a PC to an IP Telephone

You can connect a PC to some IP telephones (e.g., KX-NT300 series) using the IP telephone’s secondary

port. In this case, only a single port from the LAN’s network interface (switching hub) is required to connect

both the IP telephone and PC to the LAN.

Note

• Use an Ethernet straight cable with an RJ45 connector to connect a PC to the IP telephone. The cable

should be a CAT 5 (Category 5) or higher for 10BASE-T/100BASE-TX, or CAT 5e (Enhanced Category

5) or higher for 1000BASE-T.

• Only a PC can be connected to the secondary port of an IP telephone. Other IP telephones, including

IP-PTs, or network devices such as routers or switching hubs, cannot be connected.

• The secondary port does not support PoE for connected devices.

• In cases where a PC is connected to the secondary port, if the IP telephone connection to the PBX is

disconnected or reset, LAN communication to the PC will also be disrupted.

• Generally, it is recommended that you connect no more than one PC to the secondary port of each IP

telephone.

130 Installation Manual

4.10.2 LAN Connections for IP Telephones

Example: KX-NT346

Ethernet Straight Cable

To a PC

Installation Manual 131

4.10.2 LAN Connections for IP Telephones

4.11 Power Failure Ports

When the power supply to the PBX fails, power failure transfer (PFT) will switch from the current connection

to the Power Failure Connection. Refer to "5.5.2 Power Failure Transfer" in the Feature Guide for further

information.

Using SLC2/LCOT2 Card

In the event of a power failure, a specific SLT is automatically supplied power through the PFT port. The PFT

ports are the SLC1 port and LCOT1 port on the SLC2/LCOT2 card.

Note

A trunk conversation established during power failure can be maintained even when the power returns and

the connection is switched back to the normal configuration from the Power Failure Connection.

132 Installation Manual

4.11 Power Failure Ports

4.12 Starting the PBX

WARNING

Make sure that the AC outlet is properly earthed, then securely connect the 3-pin AC plug including

the earthed pin.

CAUTION

• Use only the AC power cord included with the PBX.

• Before touching the product (PBX, cards, etc.), discharge static electricity by touching ground or

wearing an earthing strap. Failure to do so may cause the PBX to malfunction due to static electricity.

• Once you have started the PBX, if you unplug the PBX, do not initialise it again as described in "System

Initialisation Procedure". Otherwise, your programmed data will be cleared. To restart the PBX, refer

to "6.1.5 Restarting the PBX".

• The power supply cord is used as the main disconnect device. Ensure that the AC outlet is located

near the equipment and is easily accessible.

Installing the Hook Clip for the AC Power Cord

1. Insert the hook clip into the hook clip hole.

Note

Use only the hook clip included with the PBX.

Installation Manual 133

4.12 Starting the PBX

Connecting the AC Power Cord

1. Plug the AC power cord into the PBX and pass the cord through the hook clip as indicated. Push the hook

clip in the direction of the arrow until it clicks.

Note

For safety reasons, do not stretch or pinch the AC power cord.

To UPS

2. When not using a UPS:

Plug the other end of the cord into an AC outlet.

When using a UPS:

Plug the other end of the cord into the outlet of the UPS.

Connecting an Uninterruptible Power Supply (UPS)

A UPS can be connected to the PBX and it provides temporal power to the PBX in the event of a power failure.

When using the recommended UPS (with a USB interface), the PBX can perform automatic shutdown when

the UPS battery ratio is at a specified rate by sending a warning signal to the PBX through the USB port.

Therefore, data loss or serious damage to the PBX caused by a sudden power cut can be prevented.

After power is restored, turn off the PBX using the power switch first, and then turn the PBX back on before

starting the PBX.

Note

• For details about using Web Maintenance Console to specify the UPS battery ratio to begin automatic

shutdown, refer to "4.1.1 Status—Equipment Status—UPS" in the PC Programming Manual.

• For information about the installation of an UPS, refer to the documentation of your UPS.

• For information about the recommended UPS, ask your local Panasonic dealer.

1. Connect the UPS to the USB port of the PBX.

134 Installation Manual

4.12 Starting the PBX

Note

When connecting the UPS, use only the USB cable included with the UPS and do not use USB hubs

to connect the UPS and the PBX.

To UPS

Follow the instructions in the documentation of the UPS to setup and start the UPS.

System Initialisation Procedure

Notice

When a UPS is connected, make sure it is started as instructed in the documentation for the UPS.

1. Slide the System Mode Switch to the "SYSTEM INITIALIZE" position.

STATUS Indicator System Mode Switch

2. Turn on the power switch of the PBX. The STATUS indicator will flash green.

3. While the STATUS indicator is flashing green, slide the System Mode Switch back to the "NORMAL"

position. Depending on the configuration, initialisation takes about 2.5 minutes. If successfully executed,

the STATUS indicator will stop flashing and remain lit up.

Note

When DSP card(s) are installed and a DHCP server is not connected, each installed DSP card cannot

acquire an IP address, and the STATUS indicator will turn red.

Installation Manual 135

4.12 Starting the PBX

All data, except for system prompts and activation key files, will be erased. Data that is erased includes Unified

Messaging data, call logs, etc. The settings for the PBX as well as all optional service cards will be initialised

to their default values.

Note

• After the PBX is initialised, you can restore system data to the PBX that has been backed up earlier.

For details about backing up and restoring system data, refer to "6.1 Tool—System Data Backup to

USB", "7.2.2 Utility—File—File Transfer PBX to PC" and "7.2.1 Utility—File—File Transfer PC to

PBX" in the PC Programming Manual.

• After the PBX is initialised, you must set up the mandatory settings required for both stand-alone PBXs

and PBXs in a One-look network with Easy Setup Wizard. For details refer to "Connecting to Web

Maintenance Console" and "5.4.1 Easy Setup Wizard".

Confirming the Trunk Connection

After the SLC2/LCOT2 card is installed, programme the PBX and connect trunks to the PBX.

If SLC2/LCOT2 card is not installed, this confirmation can be skipped.

To confirm that the trunks are successfully connected, dial [ ] [3] [7] + trunk number (3 digits) on an IP

telephone, or press the IP telephone’s S-CO button. You will hear a dial tone if the trunk is available and

connected.

136 Installation Manual

4.12 Starting the PBX

Section 5

Programming with Web Maintenance Console

This section describes the installation procedure,

structure, and functions of the Web Maintenance

Console for programming IP telephones and the PBX.

Further information on programming the PBX for use

with SIP trunks and a VoIP network is included.

Installation Manual 137

5.1 Overview of Web Maintenance Console

Web Maintenance Console is designed to serve as an overall system programming reference for the PBX.

You can programme and control the PBX over an IP network using Web Maintenance Console.

This section describes programming basic items using Web Maintenance Console.

Menu Buttons

Web Maintenance Console Features

Note

The contents and design of the software are subject to change without notice.

138 Installation Manual

5.1 Overview of Web Maintenance Console

5.2 PC Connection

KX-NS1000 has 3 physical ports for PC and LAN connections. A default IP address is assigned to each port.

A PC connect to the PBX either directly or over a LAN using the appropriate method for the port being used.

Port Default IP Address

MNT Port 223.0.0.1

LAN Port 192.168.0.101

WAN Port

Not Used

The WAN Port is not used with PCMPR Software Version 001.10000.

Direct Connection

To LAN Port

MNT Port

Notice

When connecting the PC to the MNT port, if the PC is set to obtain the IP address automatically, the IP

address of the PC will be set to an appropriate IP address to establish a connection to the PBX.

Note

• Use an Ethernet cable with an RJ45 connector to connect a PC to the PBX.

• For pin assignments and maximum cabling distance, refer to "4.9 Connection of Peripherals".

Connection via LAN

Switching Hub

LAN Port

LAN

Installation Manual 139

5.2 PC Connection

Note

For details about connecting a switching hub to the PBX, refer to "4.10.1 LAN Connection for the Main

Unit".

Connection via Virtual Private Network (VPN)

Switching Hub

LAN Port

LAN

Router

VPN

Notice

To access the PBX via VPN, the PC must be in the same VPN.

Note

For details about connecting a switching hub to the PBX, refer to "4.10.1 LAN Connection for the Main

Unit".

Connection via Internet

Switching Hub

LAN Port

LAN

Router

Internet

CAUTION

It is strongly recommended to use SSL encrypted communication when the PC is accessing the PBX via

the Internet. To use SSL encryption, routers must have a port set up for https communication.

Notice

To access the PBX via the internet, routers must have static NAT/NAPT settings enabled.

140 Installation Manual

5.2 PC Connection

Note

For details about connecting a switching hub to the PBX, refer to "4.10.1 LAN Connection for the Main

Unit".

Installation Manual 141

5.2 PC Connection

5.3 Starting Web Maintenance Console

System Requirements

Required Operating System

• Microsoft

Windows

XP, Windows Vista

Business, or Windows 7 Professional operating system

Recommended Display Settings

• Screen resolution: XGA (1024 ´ 768)

• DPI setting: Normal size (96 DPI)

Supported Browsers for use with Web Maintenance Console

• Windows Internet Explorer

• Windows Internet Explorer 9

• Mozilla

Firefox

version 6.0 or later.

Note

Always be sure to apply the latest updates to your Web browser software. For details, refer to your Web

browser’s documentation. Only the browsers and browser versions listed above are supported for use with

Web Maintenance Console.

This software uses the Source Code of RSA Data Security, Inc. described in the RFC1321 (MD5

Message-Digest Algorithm).

Licence to copy and use this software is granted provided that it is identified as the "RSA Data Security, Inc.

MD5 Message-Digest Algorithm" in all material mentioning or referencing this software or this function.

Licence is also granted to make and use derivative works provided that such works are identified as "derived

from the RSA Data Security, Inc. MD5 Message-Digest Algorithm" in all material mentioning or referencing the

derived work.

RSA Data Security, Inc. makes no representations concerning either the merchantability of this software or

the suitability of this software for any particular purpose. It is provided "as is" without express or implied warranty

of any kind.

These notices must be retained in any copies of any part of this documentation and/or software.

Password Security

CAUTION

To the Administrator or Installer regarding the system password

1. Please provide all system passwords to the customer.

2. To avoid unauthorised access and possible abuse of the PBX, keep the passwords secret, and inform

the customer of the importance of the passwords, and the possible dangers if they become known to

others.

3. The PBX has default passwords preset. For security, change these passwords the first time that you

programme the PBX.

4. Change the passwords periodically.

142 Installation Manual

5.3 Starting Web Maintenance Console

5. It is strongly recommended that passwords of 10 numbers or characters be used for maximum

protection against unauthorised access. For a list of numbers and characters that can be used in system

passwords, refer to "1.1.3 Entering Characters" in the PC Programming Manual.

Connecting to Web Maintenance Console

1. Connect the PC to the PBX:

• Connect the PBX to a PC with the MNT port and access the PBX directly from the PC. For details, refer

to "Direct Connection" in "5.2 PC Connection".

• Connect the PBX to a network with the LAN port and access the PBX from a PC in your LAN or VPN.

For details, refer to "Connection via LAN", "Connection via Virtual Private Network (VPN) " and

"4.10.1 LAN Connection for the Main Unit".

• Connect the PBX to a network with the LAN port and access the PBX from a PC using an Internet

connection. For details, refer to "Connection via Internet" and "4.10.1 LAN Connection for the Main

Unit".

2. Access Web Maintenance Console:

MNT Port Connection:

Launch your Web browser and in the address bar, enter the following address exactly as shown:

http://kx-ns1000.

Note

Be sure to include the period at the end as shown.

LAN or VPN Connection:

Launch your Web browser and input the IP address of the PBX followed by the Web Maintenance Console

port number into the address bar. The input method will differ according to the PC’s connection to the PBX.

The default IP address for the LAN port of the PBX is 192.168.0.101, and the default Web Maintenance

Console port number is 80. Accordingly, the address to enter to connect to the PBX for the first time will

be as follows (enter the address exactly as shown):

http://192.168.0.101

Internet Connection (SSL Connection):

When the PC is accessing the PBX from a connection over the internet, the use of SSL is strongly

recommended. When using an SSL encrypted connection, the default port is 443. The format of the address

to enter to connect to the PBX using an SSL encrypted connection will be as follows:

https://xxx.xxx.xxx.xxx:yyy

• "xxx.xxx.xxx.xxx" is the IP address of a device that can be accessed from the Internet, such as the

IP address of a network router.

• "yyy" is a port number. The network router’s port forwarding settings must be configured so that traffic

arriving at port "yyy" is forwarded to the correct IP address and port of the PBX in the LAN.

• Port forwarding settings must specify the IP address and the port number of the network router

("xxx.xxx.xxx.xxx:yyy") to transfer the packets to the PBX in the LAN, so that the packets sent to the

global IP address and specified port of the router will be transferred to the IP address and specified

port of the PBX in the LAN.

• Note the usage of "https" instead of "http".

• If you connect to Web Maintenance Console using SSL, a security alert window is displayed. Follow

the prompts to install a security certificate. The procedure may vary according to your browser.

Note

The IP address and Web Maintenance Console port number for the PBX can be changed from their

default values. If settings for the LAN port’s IP address or port number has been forgotten, connect

using the MNT port connection as described above and confirm the LAN port’s IP address in

Installation Manual 143

5.3 Starting Web Maintenance Console

"27.1 Network Service—IP Address/Ports—Basic Settings", and the port in "27.2.3 Network Service

—Server Feature—HTTP" in the PC Programming Manual.

3. The Web Maintenance Console login screen is displayed. Log in with the Installer level account name and

the default Installer level account password to launch the Easy Setup Wizard. For details about the Easy

Setup Wizard, see "5.4.1 Easy Setup Wizard".

144 Installation Manual

5.3 Starting Web Maintenance Console

5.4 Programming the PBX

5.4.1 Easy Setup Wizard

In the Easy Setup Wizard, you will set up the mandatory settings required for the PBX.

When you log in to Web Maintenance Console for a PBX that is in its initialised, factory default state, the Easy

Setup Wizard for that PBX will launch automatically. You must log in using the Installer level account name

and password.

– The Installer level account name is "INSTALLER".

– The default Installer level account password is "1234".

1. After Easy Setup Wizard launches, select a language, and then click Install.

2. In Location Setting:

a. Select a PBX Type:

• Master: Select for a PBX that will be registered as the Master unit of One-look network. Also select

for a stand-alone PBX that will not be used in a One-look network.

• Slave: Select for a PBX that will be registered as a Slave unit of a One-look network. If Slave is

selected, go to step 2-d below.

Note

If the Master unit is located on a different LAN than the Slave unit being registered, the Slave

unit will not be able to automatically detect the Master unit for registration. The IP address of

the Master unit must be specified. Enter the IP address of the Master unit in If located on

different network from Master PBX.

b. Select a Suffix Code

from the drop-down list if Master is selected for PBX Type.

c. Select an Area

from the drop-down list if Master is selected for PBX Type.

d. Click Next.

Note

If Suffix Code is changed from its default value, a notice about restarting the PBX is displayed. Click

OK to restart the PBX. After the PBX restarts, start Web Maintenance Console again (refer to

"Connecting to Web Maintenance Console" in "5.3 Starting Web Maintenance Console"). When you

start the Easy Setup Wizard again, you will start from step 3, below.

For information about Suffix Codes and Areas to select, refer to "7.6 PBX Region Suffix Codes and Areas".

3. In PBX Setting:

a. Specify a Site name if Master was selected for PBX Type in step 2.

b. Select a Time Zone from the drop-down list.

c. Click the Local Time box and select the date and time from the menu.

d. Click Next.

4. In LAN Setting, the IP addresses for the PBX, DNS server, and DSP cards can be assigned automatically

through a DHCP server or entered manually.

When using a DHCP server:

a. Select Obtain an IP address automatically.

b. Select Obtain DNS server address automatically.

c. Select Obtain DSP IP address automatically.

Notice

The boxes will turn grey and the IP address information will be assigned automatically.

Write down the address information assigned to the PBX for future reference.

Installation Manual 145

5.4.1 Easy Setup Wizard

d. Click Next.

When not using a DHCP server:

a. Select Use the following IP address.

b. Enter an IP address

, Subnet Mask

, and Default Gateway

. (The default gateway may not need to

be specified depending on your network configuration.)

c. Select Use the following DNS server address.

d. Enter the preferred and alternative DNS IP addresses

e. Select Use the following DSP IP address.

f. Enter up to 2 IP addresses

for each installed DSP card.

g. Click Next.

Valid IP address range: "1.0.0.0" to "223.255.255.255"

Valid subnet mask address range: "0–255.0–255.0–255.0–255" (except "0.0.0.0" and "255.255.255.255")

5. In Registration Setting, the IP Terminal Registration Mode and the One Look Networking (Trial

Activation Key) can be set.

a. Select the IP Terminal Registration Mode:

• Manual: Select this mode to manually register IP terminal information.

• Full Automatic: Select this mode to automatically register IP terminal information.

• Extension Number Input: Select this mode to automatically register IP terminal information except

its extension number. The extension number can then be registered from the IP telephone

manually.

Note

• Full Automatic and Extension Number Input registration methods may not be available for

certain types of IP terminals. In such cases, select the Manual registration method.

• For more information about the IP terminal registration modes, refer to "5.9.1 Registering

IP Telephones".

b. For One Look Networking (Trial Activation Key), specify whether to activate the 60-day One-look

Networking Trial Activation Key.

– If Active is selected, the 60-day trial will begin when the Easy Setup Wizard is completed.

– If Non Active is selected, you will have to activate the trial manually in order to use One-look

Networking Features on a trial basis.

c. Click Next.

If Slave has been selected in step 2, the Easy Setup Wizard will finish at this step. If LAN settings have

been changed from their default values in step 4, you will be prompted to restart the PBX. Click OK to

restart the PBX. Otherwise, the login screen will be displayed.

To add the PBX as a Slave unit PBX to the One-look network, use the Add Site Wizard from the Master

unit PBX’s Home Screen.

6. In SNTP / Daylight Saving, enter information for Automatic Time Adjustment and Daylight Saving, and

then click Next.

7. In Maintenance Setting, the Installer password, information for SNMP Setting and SNMP Manager can

be entered.

a. Enter a password for the Installer level account in Installer password. Confirm your input in

Re-enter.

b. Specify settings for SNMP Setting and SNMP Manager if necessary. If you are unsure of your

network’s SNMP settings, contact your network’s administrator.

c. Click Finish.

8. Follow the prompts of the Easy Setup Wizard. After the Easy Setup Wizard is completed, if LAN settings

have been changed from their default values in step 4, you will be prompted to restart the PBX. Click OK

to restart the PBX. Otherwise, the login screen will be displayed.

9. Log in with the Installer level account using the password entered during Easy Setup Wizard.

The Home Screen is displayed. You may now begin programming the PBX.

146 Installation Manual

5.4.1 Easy Setup Wizard

Notice

If an external DHCP server is in use, it must be able to use a "client identifier" option specified by RFC 2131.

Changing IP Address Settings

IP addressing information for the PBX can also be changed from Web Maintenance Console after the Easy

Setup Wizard has been completed.

1. Click Setup ® Network Service ® IP Address/Ports.

2. Click the Basic Settings tab.

3. When using a DHCP server:

a. Select Obtain an IP address automatically.

b. Select Obtain DNS server address automatically.

c. Select Obtain DSP IP address automatically.

Notice

The boxes will turn grey and the IP address information will be assigned automatically.

Write down the address information assigned to the PBX for future reference.

When not using a DHCP server:

a. Select Use the following IP address.

b. Enter an IP address

, Subnet Mask

, and Default Gateway

(The default gateway may not need to be specified depending on your network configuration.)

c. Select Use the following DNS server address.

d. Enter the preferred and alternative DNS IP addresses

e. Select Use the following DSP IP address.

f. Enter up to 2 IP addresses

for each installed DSP card.

4. Click OK.

a. A screen will appear stating that any changes made in step 3 will be activated after the PBX is restarted.

b. Click OK.

5. Restart the PBX.

a. Click Maintenance ® System Control ® System Reset.

b. On the System Reset screen, click Backup.

Valid IP address range: "1.0.0.0" to "223.255.255.255"

Valid subnet mask address range: "0–255.0–255.0–255.0–255" (except "0.0.0.0" and "255.255.255.255")

Notice

• Do not change the IP address of the PBX once IP telephones are registered to the PBX using the set

IP address. The IP telephones will not operate properly if the IP address of the PBX is changed. When

an external DHCP server is used to automatically assign IP addresses, it must be configured to always

allocate the same IP address to the PBX. For details, consult your network administrator.

• If an external DHCP server is in use, it must be able to use a "client identifier" option specified by RFC

2131.

• If an external DHCP server is in use, the KX-NS1000 DHCP Server feature must be disabled.

• The PBX will not start properly if IP addresses cannot be assigned automatically by the DHCP server

when the PBX has been set to obtain IP addresses automatically. In this case, you need to consult

your network administrator because the DHCP server in your network may not be running or a network

failure may have occurred. If the DHCP server is not available, enter IP addresses manually, then

restart the PBX. If the PBX cannot be accessed over the network, connect the PC directly to the PBX

with an Ethernet cable and access Web Maintenance Console using a direct connection.

For details about connecting the PC directly to the PBX, refer to "Direct Connection" in "5.2 PC

Connection".

Installation Manual 147

5.4.1 Easy Setup Wizard

• During a long programming session, it is highly recommended that you periodically save the system

data to the Storage Memory Card. If the PBX undergoes a sudden power failure or if the system is

reset for some reason, all the system data in RAM will be lost. However, if system data has been saved

to the Storage Memory Card, it can be easily reloaded.

To save the system data to the Storage Memory Card while programming, click the disk button ( )

® Yes ® OK. Be sure to save the system data to the Storage Memory Card before restarting the PBX,

or any changes may be lost.

• When no operations are performed for more than 60 minutes (default), you will be automatically logged

out from Web Maintenance Console and unsaved data will be lost.

Changing the Display Language

The language used for Web Maintenance Console can be changed after the Easy Setup Wizard has completed.

1. Click Setup ® Users ® User Profiles.

2. Select the check box for the Installer level account.

3. Click

The Edit User screen will be displayed.

4. Select the preferred language in Change Language.

5. Click OK.

The screen will redisplay in the selected language immediately.

5.4.2 Enabling the DHCP Server Feature

This PBX is equipped with a DHCP Server feature. When the feature is enabled, it allows you to centrally

manage and automate the assignment of IP addresses for the devices located in same LAN using Web

Maintenance Console.

Click Setup ® Network Service ® Server Feature ®

DHCP.

2. On the DHCP Server tab, select Enable for DHCP

Server.

3. Enter valid settings for the IP address auto

assignment.

Note

For details about IP address auto assignment

settings, refer to "27.2.1 Network Service—Server

Feature—DHCP" in the PC Programming Manual.

4. Click OK.

Note

If an external DHCP server is in use, do not enable the DHCP Server feature. Doing so may allocate

inappropriate IP addressing information to the devices.

148 Installation Manual

5.4.2 Enabling the DHCP Server Feature

5.4.3 Installing the Virtual IP Cards to the PBX

a. Click Setup ® PBX Configuration ®

Configuration ® Slot.

b. Click Virtual.

a. Click on the name of the desired card.

b. From the Total number of cards drop-down list,

select the desired number of cards.

3. A confirmation message will be displayed. Click OK.

5.4.4 Installing Additional Activation Keys

The corresponding number of IP trunks, IP telephones or enhanced features can be activated by installing the

downloaded activation key file(s) using Web Maintenance Console.

Installing the Activation Key Files

Be sure to connect the PC to the PBX in advance. For details about Web Maintenance Console, refer to

"5.3 Starting Web Maintenance Console".

1. Log in to Web Maintenance Console using the Installer level account.

2. Click Maintenance ® Utility ® Activation Key Installation.

Activation Key Installation window will be displayed.

3. Click Browse and specify the directory where the activation key files are stored, and click Open.

4. A list of activation key files stored in the specified directory is displayed. Check the boxes next to the

activation keys to install to the PBX, and click Install.

5. The activation keys will be copied to the Master unit, and then the activation keys that Slave units require

will be copied to the Slave units of the One-look network. When installation is complete, the message,

"The activation key has been installed and activated successfully!" is displayed.

6. Click Apply.

Notice

The activation key file can only be installed in the PBX with the MPR ID number entered when the activation

key file was downloaded. The activation key file cannot be reissued unless the mother board crashes.

Note

• You can click the provided link to directly access activation key information and programme the number

of activated IP trunks and IP softphones.

• For information about programming activation keys using Web Maintenance Console, refer to "9.3 PBX

Configuration—Configuration—Slot—Activation Key" in the PC Programming Manual.

5.4.5 Configuration of the Activation Keys

Depending on your configuration, it may be necessary to programme the number of provided IP Trunk channels

to be used for H.323 trunks. By default, all of the provided IP Trunk channels will be used for SIP trunks.

Installation Manual 149

5.4.5 Configuration of the Activation Keys

Similarly, you can programme how many IP softphone(s) can be used through the IP Softphone/IP Proprietary

Telephone activation key. By default, only IP softphone(s) can be used through the IP Softphone/IP Proprietary

Telephone activation key.

a. Click Setup ® PBX Configuration ®

Configuration ® Slot.

b. Click Activation Key.

a. In Number of activated IP-GW, type the number of

IP Trunk channels to be used for H.323 trunks.

Note

If you have changed the value for Number of

activated IP-GW, you must click Execute to

restart the V-IPGW cards for the change to take

effect.

b. In Number of activated IP-Softphone, type the

number of IP softphones to be used through the IP

Softphone/IP Proprietary Telephone activation key.

3. Click OK.

150 Installation Manual

5.4.5 Configuration of the Activation Keys

5.5 Programming a One-look Network

The Add Site Wizard, which is run from the Home Screen of the Master unit, will add other KX-NS1000 PBXs

connected to the private IP network to your One-look network as Slave units.

Note

The PBX to be added must have been configured as a Slave unit using the Easy Setup Wizard.

For details about Easy Setup Wizard, see "5.4.1 Easy Setup Wizard".

1. To start the Add Site Wizard, click the Add Slave button

( ) on the Home screen.

2. Follow the prompts of the Add Site Wizard to complete

following settings:

• PBX Setting

• Registration Setting

• SNTP / Daylight Saving

• Maintenance Setting

Note

• The parameters which appear in the settings

above are described in "5.4.1 Easy Setup

Wizard".

• If 2 or more sites will be added to the One-look

network, repeat steps 1 to 2 for each site.

3. After the Add Site Wizard is completed, click

Registration on the List View of the Home screen.

4. A list of KX-NS1000 PBXs set up as Slave units will be

displayed under Available sites for registration.

Select PBXs by their assigned site names and click the

right arrow to move them to Selected sites for

registration.

Click Next to start the registration process.

5. On the Registration screen, the status of PBXs being

registered is displayed.

6. On the Registration screen, the result of the registration

process is shown. Click Close to continue.

Registered Slave PBXs can now be viewed and selected on the Home Screen for programming.

MASTER LED Transition

When adding Slave units, the MASTER LED of each unit changes as shown in the following table:

Installation Manual 151

5.5 Programming a One-look Network

Master

Slave (When Slave unit power is

turned on before Master unit)

Slave (When Slave unit power is

turned on after Master unit)

Operation MASTER LED Operation MASTER LED Operation MASTER LED

Power On Amber

(Flashing)

Power On Amber

(Flashing)

Add Site Wizard Green

Add Site Wizard

is Completed

Green Being

Registered

Amber

(Flashing)

Registration is

Completed

Amber Power On Amber

(Flashing)

Being

Registered

Amber

(Flashing)

Registration is

Completed

Amber

152 Installation Manual

5.5 Programming a One-look Network

5.6 Programming a H.323 QSIG Network

There are 2 methods to programme the Virtual 16-Channel VoIP Gateway Card (V-IPGW16 card) to establish

VoIP communications between PBXs at different locations, as follows:

PBX code method The caller dials the unique PBX code of the PBX to which the called party is

connected, in addition to the destination number.

Extension number

method

The caller dials only the destination number of the called party to call through

PBXs at different locations (hence there are fewer digits to dial than with the

PBX code method).

Note

• For a detailed explanation about each method, refer to "4.1 Public Network Features" in the Feature

Guide.

portions of the Software and documentation are owned by RADVISION and are protected by United

States copyright laws, other applicable copyright laws and international treaty provisions. RADVISION

and its suppliers retain all rights not expressly granted.

5.6.1 Assigning the Hunt Pattern

The hunt pattern determines how to route incoming calls through virtual IP trunks to the PBX. The procedure

below demonstrates the process of programming the hunt pattern of the local PBX. After the hunt pattern at

the local PBX has been fully assigned, repeat the procedure for the hunt pattern at the remote PBX with the

appropriate setting values.

Status Light

a. Click Setup ® PBX Configuration ®

Configuration ® Slot.

b. Click Virtual ® V-IPGW16.

c. If the V-IPGW16 card’s status light is green, move

the mouse pointer over the card, select Ous from the

menu that appears, and then click OK on the

dialogue box. The status light will turn red.

d. Move the mouse pointer over the installed

V-IPGW16 card. A menu will be shown under the

mouse pointer.

e. Click Shelf Property.

f. Click Hunt Pattern.

a. When using the PBX code method:

In the Leading Number cell, type the local PBX

code and extension starting digit.

When using the extension number method:

In the Leading Number cell, type the local extension

starting digit.

b. Click OK to return to the Shelf Property screen.

Installation Manual 153

5.6.1 Assigning the Hunt Pattern

Note

For more details about hunt pattern assignment, refer to "9.11.2 PBX Configuration—Configuration—Slot

—Shelf Property - Virtual IP Gateway—Hunt Pattern" in the PC Programming Manual.

5.6.2 Programming the Address Translation Table

The function of an address translation table in a VoIP network is to provide 2-way translation of telephone

numbers and IP addresses

. Therefore, a caller can reach the destination by dialling the number without

knowing the destination IP address.

The procedure below demonstrates the process of programming the address translation table at the local PBX.

After the address translation table at the local PBX has been fully programmed, repeat the procedure for the

address translation table at the remote PBX with the appropriate setting values.

a. Click Setup ® PBX Configuration ®

Configuration ® Slot.

b. Click System Property.

c. Click the V-IPGW tab.

d. Click GW Settings.

2. In the Main tab, do the following to configure the

gateway entry for the remote PBX:

a. In the GW Name cell, type a unique identifier of the

destination in the VoIP network.

b. In the GW IP Address cell, type the IP address of

the destination gateway device.

c. In the GW Group cell, select None.

Note

Having the value None for GW Group means

that the destination gateway device does not

belong to any gateway group. Grouping is useful

when installing multiple gateway devices at one

location. For details, refer to "9.4 PBX

Configuration—Configuration—Slot—System

Property— GW Group" in the PC

Programming Manual.

d. Click OK to return to the System Property screen.

IP address-to-telephone number translation can also be handled by using an H.323 Gatekeeper device. To configure Gatekeeper

devices, refer to the manufacturer’s documentation. This manual focuses on the method using the V-IPGW16 card’s internal address

translation capabilities.

154 Installation Manual

5.6.2 Programming the Address Translation Table

a. Click Setup ® PBX Configuration ®

Configuration ® Slot.

b. Click System Property.

c. Click the V-IPGW tab.

d. Click DN2IP.

e. When using the PBX code method:

In the Leading Number cell, type the remote PBX

code and starting digit of destination extension.

When using the extension number method:

In the Leading Number cell, type the remote PBX

code and starting digit of destination extension.

f. In the Remaining Number of Digits cell, type a

number of digits to dial following the leading number.

g. In GW No./GW Group Selection, select GW No.

h. In the GW No. cell, select 1 (the gateway entry for

the destination gateway device at the remote PBX).

i. Click OK.

Note

For more details about gateway settings, refer to "9.4 PBX Configuration—Configuration—Slot—System

Property—GW Settings–Main" in the PC Programming Manual.

Installation Manual 155

5.6.2 Programming the Address Translation Table

5.6.3 Programming the Network Settings

For successful operation of a VoIP network using the V-IPGW16 card, network settings for the PBX at each

location must be programmed appropriately. For a detailed discussion of related features, refer to the Feature

Guide.

This section details the procedure to programme the network settings for the local PBX. After the programming

for the local PBX has been done, repeat the procedure for the remote PBX with the appropriate setting values.

The following procedures describe the process of programming the network settings for each numbering

method.

Programming for the PBX Code Method

a. Click Setup ® PBX Configuration ®

Configuration ® Slot.

b. Click Virtual ® V-IPGW16.

c. Move the mouse pointer over the installed

V-IPGW16 card to display the menu of options, and

click Ous (out of service) to set the card to out of

service.

d. Repeat step c for each installed V-IPGW16 card until

all V-IPGW16 cards are OUS.

e. Move the mouse pointer over the installed

V-IPGW16 card to display the menu of options, and

click Port Property.

Confirm that all V-IPGW16 cards are OUS.

Note

When a V-IPGW16 card is installed, 8 ports are

available for the card (a port has 2 channels).

a. Click Setup ® PBX Configuration ® CO &

Incoming Call.

b. Click CO Line Settings.

c. Type the CO Name and assign an unused Trunk

Group Number to be used for all IP trunks.

d. Click OK.

156 Installation Manual

5.6.3 Programming the Network Settings

a. Click Setup ® PBX Configuration ® System.

b. Click Numbering Plan.

c. Click Main.

d. Click the Features tab.

e. In the TIE Line Access cell, type the dialling

number.

f. Click OK.

a. Click Setup ® PBX Configuration ® Private

Network.

b. Click TIE Table.

c. In the Own PBX Code cell, type the PBX code of the

local PBX in the network.

d. In the first unused Leading Number cell, type the

PBX code of the remote PBX in the network.

e. In the corresponding Trunk Group list, select the

number of the trunk group to be used when making

calls.

f. Set the number modification pattern, if necessary.

g. Click OK.

a. Click Setup ® PBX Configuration ®

Configuration ® Slot.

b. Click Virtual ® V-IPGW16.

c. Move the mouse pointer over the installed

V-IPGW16 card to display the menu of options, and

click Ins (in service).

d. Repeat step c for each installed V-IPGW16 card until

all V-IPGW16 cards are INS.

Programming for the Extension Number Method

a. Click Setup ® PBX Configuration ®

Configuration ® Slot.

b. Click Virtual ® V-IPGW16.

c. Move the mouse pointer over the installed

V-IPGW16 card to display the menu of options.

d. Click Port Property.

Installation Manual 157

5.6.3 Programming the Network Settings

Confirm that all V-IPGW16 cards are set to OUS.

Note

When a V-IPGW16 card is installed, 8 ports are

available for the card.

a. Click Setup ® PBX Configuration ® CO &

Incoming Call.

b. Click CO Line Settings.

c. Type the CO Name and assign an unused Trunk

Group Number to be used for all IP trunks.

d. Click OK.

a. Click Setup ® PBX Configuration ® System.

b. Click Numbering Plan.

c. Click Main.

d. Click the Other PBX Extension tab.

e. In the Dial (3 digits) cell, type a starting digit of

destination extension.

f. Click OK.

a. Click Setup ® PBX Configuration ® Private

Network.

b. Click TIE Table.

c. In the Leading Number cell, type the starting digit

of destination extension.

d. Click OK.

158 Installation Manual

5.6.3 Programming the Network Settings

a. Click Setup ® PBX Configuration ®

Configuration ® Slot.

b. Click Virtual ® V-IPGW16.

c. Move the mouse pointer over the installed

V-IPGW16 card to display the menu of options, and

click Ins.

d. Repeat step c for each installed V-IPGW16 card until

all V-IPGW16 cards are INS.

Note

For details about network parameter settings, refer to the relevant sections of the PC Programming Manual.

Installation Manual 159

5.6.3 Programming the Network Settings

5.7 Programming SIP Trunks

The Virtual 16-Channel SIP Trunk Card (V-SIPGW16) is a virtual trunk card which is designed to be easily

integrated into an Internet Telephony Service provided by an ITSP (Internet Telephony Service Provider).

Various settings can be programmed for each virtual SIP gateway port.

Accessing Port Properties

Click Setup ® PBX Configuration ® Configuration

® Slot.

2. Click Virtual.

3. Move the mouse pointer over the V-SIPGW16 card.

4. Click Port Property.

Programming Port Properties

Automatic Programming

Some of the parameters can be automatically programmed by selecting the desired SIP provider for each

virtual SIP gateway port. Available SIP providers can be selected, and a different SIP provider can be assigned

to each virtual SIP gateway port.

Note

It is necessary to import a SIP provider list file (comma-separated value [CSV] file) in advance to use the

automatic programming feature.

Follow the steps below to configure a SIP provider.

1. Click Select Provider.

A dialogue box will appear. Available virtual SIP gateway port numbers are displayed in the list.

2. From the Provider menu, select the desired SIP provider.

Note

If the desired SIP provider is not shown in the drop-down list, it is necessary to programme the desired

parameters manually. For information about the manual programming procedure, refer to "Manual

Programming" below.

3. Highlight the desired port numbers or click Select All to select all the virtual SIP gateway port numbers to

be assigned to the SIP provider selected in step 2.

4. Click Execute.

Appropriate setting values designated by the SIP provider will be set in the parameters for the virtual SIP

gateway ports.

Manual Programming

Follow the steps below to programme the parameters which are not automatically programmed by selecting a

provider.

1. Click the desired tab.

2. Enter information or select settings from the drop-down list for each parameter.

Parameters that Require Manual Programming

160 Installation Manual

5.7 Programming SIP Trunks

Manual programming is compulsory for the following parameters:

• User Name: Specifies the user name (SIP Account) provided by the SIP provider. (Max. 64 characters)

• Authentication ID: Specifies the authentication ID required for registration with the SIP server. (Max. 64

characters)

• Authentication Password: Specifies the authentication password used for registration with the SIP

provider. (Max. 32 characters)

Follow the steps below to programme these 3 parameters.

1. Click an Account tab.

2. In the User Name column, enter the user name provided

by the SIP provider.

3. In the Authentication ID column, enter the

authentication ID required for registration with the SIP

server.

4. In the Authentication Password column, the

authentication password used for registration with the

SIP provider.

5. Click OK.

Adding Settings to Provider Profiles

Follow the steps below to add the settings to provider profiles.

1. Click Add Provider.

A dialogue box will appear. Available virtual SIP gateway

port numbers are displayed in the list.

2. Highlight the desired port numbers or click Select All to

select all the virtual SIP gateway port numbers to add

the settings to provider profiles.

3. Click Execute.

Note

For more details about SIP gateway port settings, refer to the PC Programming Manual.

Installation Manual 161

5.7 Programming SIP Trunks

5.8 Assigning Networking Information to IP

Telephones

5.8.1 Assigning IP Addressing Information

The IP telephone’s IP address, subnet mask address and default gateway address, and the PBX’s IP address

must be assigned to the IP telephone before it can be used on the network. This IP addressing information

can be assigned in the following ways:

For IP-PTs

• Using a DHCP server (DHCP Server feature or an external DHCP server) when the IP-PT is on the

same LAN as the PBX

The DHCP server automatically assigns the IP address of the IP-PT, the subnet mask address, and the

default gateway address to the IP-PT.

The PBX’s IP address can also be assigned automatically to the IP-PT in the process of being registered

to the PBX. For details about registering the IP-PT, refer to "5.9.1 Registering IP Telephones".

Note

For information about the DHCP Server feature, refer to "7.1.2 DHCP (Dynamic Host Configuration

Protocol) Server".

• Using a DHCP server (DHCP Server feature or an external DHCP server) when the IP-PT is on a

remote office LAN

While the DHCP server automatically assigns the IP address of the IP-PT, the subnet mask address, and

the default gateway address to the IP-PT, the PBX’s IP address must be assigned manually.

Follow the procedure below to assign the PBX’s IP address.

If you need to set VLAN parameters, follow the procedure described in "5.8.2 Setting VLAN

Parameters" after assigning the IP addresses, without ending programming.

Note

• By assigning the PBX’s IP address to one IP-PT, it is possible to assign the PBX’s IP address to

other IP-PTs or IP-CSs on the same LAN through system programming. For details, refer to

"9.14 PBX Configuration—Configuration—Slot—V-IPEXT32—Port Property—Option—

ANNOUNCE Mode" in the PC Programming Manual.

• IP-PTs can only receive IP addressing information from a DHCP server on its own LAN. Therefore,

when IP-PTs are located on several LANs, a DHCP server is required on each LAN.

• Since the default setting of the DHCP client function is enabled for IP-PTs, simply connect the

IP-PTs to the LAN to use the DHCP server.

162 Installation Manual

5.8.1 Assigning IP Addressing Information

KX-NT300 series (except KX-NT321)

PBX IP Address

ENTER ENTER

Select "PBX". Select "PBX IP Address". Select "Primary PBX".

ENTER ENTER

To enter the IP address of the PBX

Press

"SETUP"

when it is displayed.

SETUP

To start programming

Supply power to the IP-PT.

To enter the IP address of the Secondary PBX (optional for software version 2.00 or

later only)

PBX IP Address

Software version 2.00 or later only

Select "Secondary PBX".

ENTER ENTER

To the VLAN settings

Press

"STORE".

To end programming

To set VLAN parameters

The IP-PT will reboot

and can then be

registered to the PBX.

STORE

Return to the

Menu screen.

Installation Manual 163

5.8.1 Assigning IP Addressing Information

KX-NT321

Press PROGRAM

while "Searching" is displayed.

To start programming

Supply power to the IP-PT.

To enter the IP address of the PBX

To the VLAN settings

The IP-PT will reboot

and can then be

registered to the PBX.

To end programming

To set VLAN parameters

Press HOLD twice to return

to the Menu screen.

Select "PBX IP

Address".

Press SP-PHONE.

Press STORE.

Select "PBX". Press SP-PHONE.

Press SP-PHONE.

Select "Primary

PBX".

Press SP-PHONE.

Select "Secondary

PBX".

Press SP-PHONE.

To enter the IP address of the Secondary PBX (if required)

PBX IP Address

Note

To confirm the connection to the secondary PBX after assigning IP addressing information, (1) turn the

IP-PT’s power off, and (2) hold the STORE button and 2 key while turning the power on.

164 Installation Manual

5.8.1 Assigning IP Addressing Information

KX-NT265 (Software version 2.00 or later only)

PBX IP

Address

To enter the IP address of the PBX

Press PROGRAM

while "Searching" is displayed.

To start programming

Supply power to the IP-PT.

PROG.

Press HOLD to return

to the Menu screen.

HOLD

Press VOLUME

to select "PBX".

VOL

Press SP-PHONE

twice.

Press SP-PHONE.

To the VLAN settings

The IP-PT will reboot

and can then be

registered to the PBX.

To end programming

To set VLAN parameters

Press STORE.

Installation Manual 165

5.8.1 Assigning IP Addressing Information

• Not using a DHCP server (DHCP Server feature or an external DHCP server) when the IP-PT is on

the same LAN as the PBX

Only the PBX’s IP address can be assigned automatically to the IP-PT in the process of being registered

to the PBX. For details about registering the IP-PT, refer to "5.9.1 Registering IP Telephones".

Follow the procedure below to assign the IP address of the IP-PT, the subnet mask address, and the default

gateway address manually.

If you need to set VLAN parameters, follow the procedure described in "5.8.2 Setting VLAN

Parameters" after assigning the IP addresses, without ending programming.

KX-NT300 series (except KX-NT321)

Select "Network".

ENTER

Select "Disable"

for DHCP setting.

ENTER

IP Address*

ENTER

To set the IP address of the IP-PT

Select "Default Gateway".

ENTER

Default Gateway Address*

ENTER

To set the default gateway address (if required)

To set the subnet mask address

Select "Subnet Mask".

ENTER

Subnet Mask Address*

ENTER

Select "IP Address".

To start programming

Press

"SETUP" when it is displayed.

SETUP

Supply power to the IP-PT.

Return to the

Menu screen.

To enter the IP address of the Secondary PBX (optional for software version 2.00 or

later only)

PBX IP Address

ENTER ENTER

Select "PBX".

Select "PBX IP

Address".

ENTER ENTER

Select "Secondary

PBX".

Continued on next page

166 Installation Manual

5.8.1 Assigning IP Addressing Information

To the VLAN settings

Press

"STORE".

STORE

To end programming

To set VLAN parameters

The IP-PT will reboot

and can then be

registered to the PBX.

Return to the

Menu screen.

Return to the

Menu screen.

Continued from previous page

Valid IP address range: "1.0.0.0" to "223.255.255.255"

Valid subnet mask address range: "0–255.0–255.0–255.0–255" (except "0.0.0.0" and "255.255.255.255")

Valid IP address range: "1.0.0.0" to "223.255.255.255"

Installation Manual 167

5.8.1 Assigning IP Addressing Information

KX-NT321

IP Address*

Subnet Mask Address*

Default Gateway Address*

To set the IP address of the IP-PT

To set the subnet mask address

To set the default gateway address (if required)

To start programming

Supply power to the IP-PT.

Press PROGRAM

while "Searching" is displayed.

Select "Network". Press SP-PHONE. Select "DHCP (Disable)". Press SP-PHONE

twice.

Press SP-PHONE.

Select "Subnet Mask". Press SP-PHONE. Press SP-PHONE.

Select "Default GW". Press SP-PHONE. Press SP-PHONE.

Press HOLD to return

to the Menu screen.

To enter the IP address of the Secondary PBX (if required)

Select "PBX IP

Address".

Press SP-PHONE.

Select "PBX". Press SP-PHONE.

Select "Secondary

PBX".

Press SP-PHONE.

PBX IP Address

Press HOLD twice to return

to the Menu screen.

Continued on next page

168 Installation Manual

5.8.1 Assigning IP Addressing Information

Continued from previous page

To the VLAN settings

The IP-PT will reboot

and can then be

registered to the PBX.

To end programming

To set VLAN parameters

Press STORE.

Valid IP address range: "1.0.0.0" to "223.255.255.255"

Valid subnet mask address range: "0–255.0–255.0–255.0–255" (except "0.0.0.0" and "255.255.255.255")

Valid IP address range: "1.0.0.0" to "223.255.255.255"

Note

To confirm the connection to the secondary PBX after assigning IP addressing information, (1) turn the

IP-PT’s power off, and (2) hold the STORE button and 2 key while turning the power on.

Installation Manual 169

5.8.1 Assigning IP Addressing Information

KX-NT265 (Software version 2.00 or later only)

IP Address*

Subnet Mask Address*

Default Gateway Address*

To set the IP address of the IP-PT

To set the subnet mask address

To set the default gateway address (if required)

To start programming

Supply power to the IP-PT.

Press PROGRAM

while "Searching" is displayed.

PROG.

Press VOLUME to

select "Network".

VOL

Press SP-PHONE. Press VOLUME to

select "DHCP (Disable)".

VOL

Press SP-PHONE

twice.

Press SP-PHONE.

Press VOLUME to

select "Subnet Mask".

VOL

Press SP-PHONE. Press SP-PHONE.

Press VOLUME to

select "Default GW".

VOL

Press SP-PHONE. Press SP-PHONE.

To the VLAN settings

The IP-PT will reboot

and can then be

registered to the PBX.

To end programming

To set VLAN parameters

Press STORE.Press HOLD to return

to the Menu screen.

HOLD

Press HOLD to return

to the Menu screen.

HOLD

Valid IP address range: "1.0.0.0" to "223.255.255.255"

Valid subnet mask address range: "0–255.0–255.0–255.0–255" (except "0.0.0.0" and "255.255.255.255")

Valid IP address range: "1.0.0.0" to "223.255.255.255"

170 Installation Manual

5.8.1 Assigning IP Addressing Information

• Not using a DHCP server (DHCP Server feature or an external DHCP server) when the IP-PT is on

a remote office LAN

All of the IP addressing information must be assigned manually.

Follow the procedure below to assign the IP addressing information.

If you need to set VLAN parameters, follow the procedure described in "5.8.2 Setting VLAN

Parameters" after assigning the IP addresses, without ending programming.

Note

By assigning the PBX’s IP address to one IP-PT, it is possible to assign the PBX’s IP address to other

IP-PTs or IP-CSs on the same LAN through system programming. For details, refer to "9.14 PBX

Configuration—Configuration—Slot—V-IPEXT32—Port Property—Option— ANNOUNCE Mode" in

the PC Programming Manual.

Installation Manual 171

5.8.1 Assigning IP Addressing Information

KX-NT300 series (except KX-NT321)

Select "Network".

ENTER

Select "Disable"

for DHCP setting.

ENTER

IP Address*

ENTER

To set the IP address of the IP-PT

To set the subnet mask address

To set the default gateway address

Select "Default Gateway".

ENTER

Default Gateway Address*

ENTER

Subnet Mask Address*

ENTER

Select "Subnet Mask".

Select "IP Address".

To start programming

Press

"SETUP" when it is displayed.

SETUP

Supply power to the IP-PT.

Select "PBX".

Return to the

Menu screen.

PBX IP Address

ENTER

To enter the IP address of the PBX

Select "PBX IP

Address".

Select "Primary

PBX".

ENTER

Software version 2.00 or later only

Continued on next page

172 Installation Manual

5.8.1 Assigning IP Addressing Information

To enter the IP address of the Secondary PBX (optional for software version 2.00 or

later only)

PBX IP Address

Select "Secondary PBX".

ENTER ENTER

Continued from previous page

To the VLAN settings

Press

"STORE".

STORE

To end programming

To set VLAN parameters

The IP-PT will reboot

and can then be

registered to the PBX.

Return to the

Menu screen.

Return to the

Menu screen.

Valid IP address range: "1.0.0.0" to "223.255.255.255"

Valid subnet mask address range: "0–255.0–255.0–255.0–255" (except "0.0.0.0" and "255.255.255.255")

Valid IP address range: "1.0.0.0" to "223.255.255.255"

Installation Manual 173

5.8.1 Assigning IP Addressing Information

KX-NT321

IP Address*

Subnet Mask Address*

Default Gateway Address*

To set the IP address of the IP-PT

To set the subnet mask address

To set the default gateway address

To start programming

Supply power to the IP-PT.

Press PROGRAM

while "Searching" is displayed.

Select "Network". Press SP-PHONE. Select "DHCP (Disable)". Press SP-PHONE

twice.

Press SP-PHONE.

Select "Subnet Mask". Press SP-PHONE. Press SP-PHONE.

Select "Default GW". Press SP-PHONE. Press SP-PHONE.

Continued on next page

Press HOLD to return

to the Menu screen.

To enter the IP address of the PBX

Select "PBX IP

Address".

Press SP-PHONE.

Select "PBX". Press SP-PHONE.

Select "Primary

PBX".

Press SP-PHONE.

Select "Secondary

PBX".

Press SP-PHONE.

To enter the IP address of the Secondary PBX (if required)

PBX IP Address

174 Installation Manual

5.8.1 Assigning IP Addressing Information

Continued from previous page

To the VLAN settings

The IP-PT will reboot

and can then be

registered to the PBX.

To end programming

To set VLAN parameters

Press HOLD twice to return

to the Menu screen.

Press STORE.

Valid IP address range: "1.0.0.0" to "223.255.255.255"

Valid subnet mask address range: "0–255.0–255.0–255.0–255" (except "0.0.0.0" and "255.255.255.255")

Valid IP address range: "1.0.0.0" to "223.255.255.255"

Note

To confirm the connection to the secondary PBX after assigning IP addressing information, (1) turn the

IP-PT’s power off, and (2) hold the STORE button and 2 key while turning the power on.

Installation Manual 175

5.8.1 Assigning IP Addressing Information

KX-NT265 (Software version 2.00 or later only)

IP Address*

Subnet Mask Address*

Default Gateway Address*

To set the IP address of the IP-PT

To set the subnet mask address

To set the default gateway address

To enter the IP address of the PBX

To start programming

Supply power to the IP-PT.

Press PROGRAM

while "Searching" is displayed.

PROG.

Press VOLUME to

select "Network".

VOL

Press SP-PHONE. Press VOLUME to

select "DHCP (Disable)".

VOL

Press SP-PHONE

twice.

Press SP-PHONE.

Press VOLUME to

select "Subnet Mask".

VOL

Press SP-PHONE. Press SP-PHONE.

Press VOLUME to

select "Default GW".

VOL

Press SP-PHONE. Press SP-PHONE.

Press HOLD

twice to return

to the Menu screen.

HOLD

Press VOLUME

to select "PBX".

VOL

Press SP-PHONE

twice.

Press

SP-PHONE.

To the VLAN settings

The IP-PT will reboot

and can then be

registered to the PBX.

To end programming

To set VLAN parameters

Press STORE.

PBX IP

Address

Press HOLD

to return to the

Menu screen.

HOLD

Valid IP address range: "1.0.0.0" to "223.255.255.255"

Valid subnet mask address range: "0–255.0–255.0–255.0–255" (except "0.0.0.0" and "255.255.255.255")

Valid IP address range: "1.0.0.0" to "223.255.255.255"

176 Installation Manual

5.8.1 Assigning IP Addressing Information

For KX-UT Series SIP Phones

Notice

When you want to use a KX-UT series SIP phone that has already been used with another PBX, or that

has had its settings programmed, you must reset the SIP phone to its factory default before assigning new

IP address information as detailed in the following procedure.

For details, refer to the documentation for the KX-UT series SIP phone.

Assigning the IP addressing information to the SIP phone

• Using a DHCP server (DHCP Server feature or an external DHCP server) to automate the assignment

of IP addressing information

The DHCP server automatically assigns the IP address of the SIP phone, the subnet mask address, and

the default gateway address to the SIP phone.

The PBX’s IP address can also be assigned automatically to the SIP phone in the process of being

registered to the PBX. For details about registering the SIP phone, refer to "5.9.1 Registering IP

Telephones".

Note

For information about the DHCP Server feature, refer to "7.1.2 DHCP (Dynamic Host Configuration

Protocol) Server".

• Not using a DHCP server (DHCP Server feature or an external DHCP server) when assigning IP

addressing information

Only the PBX’s IP address can be assigned automatically to the SIP phone in the process of being

registered to the PBX. For details about registering the SIP phone, refer to "5.9.1 Registering IP

Telephones". The IP address of the SIP phone, the subnet mask address, and the default gateway address

must be assigned manually. For instructions, refer to the documentation of the SIP phone.

Note

• When the PBX is not in the same network as the SIP phone, the IP address of the PBX must be

assigned manually. For instructions for manually setting PBX network information, refer to

"Assigning the IP address of the PBX to a SIP phone".

• When assigning IP addressing information to the SIP phone, do not use the phone’s Web user

interface programming.

Assigning the IP address of the PBX to a SIP phone

The IP address of the PBX is automatically assigned to a SIP phone when the SIP phone is in the same LAN

as the PBX. However, when the SIP phone is in a different LAN from the PBX, the following procedure is

required to assign the IP address of the PBX manually with using Web user interface.

Notice

Do not perform any other operation rather than following procedure with Web user interface. Otherwise

the SIP phone may not work properly. In that case, contact an authorised Panasonic Factory Service

Centre.

1. Prepare a configuration file to specify the IP address of the PBX.

a. Open a text editor on a PC, and then write exactly same as the following:

# PCC Standard Format File # DO NOT CHANGE THIS LINE!

### Management Server Settings #######

ACS_URL="http://xxx.xxx.xxx.xxx:yyy/cwmp/cwmpAction.cgi"

Installation Manual 177

5.8.1 Assigning IP Addressing Information

Notice

• For "xxx.xxx.xxx.xxx:yyy", enter the IP address and port number of the network router which is

in a same LAN with the PBX.

The router accessed by the SIP phone must have static NAT/NAPT settings enabled so that

the packets sent to xxx.xxx.xxx.xxx:yyy to be transferred to the PBX. For details, refer to

"Connection via Internet" in "5.2 PC Connection" and "Internet Connection (SSL

Connection):" in "5.3 Starting Web Maintenance Console".

• Configuration files must end with an empty line.

b. Save the text file as "UT_ACS.cfg".

2. Confirm the IP address of the SIP phone.

a. Press Setting or Setup (soft button) on the SIP phone.

b. Select "Information Display", then press [ENTER].

c. Select "IP address".

The IP address of the SIP phone will be displayed.

d. Press [CANCEL].

3. Open the port of the SIP phone, which is used by the PCs to access Web user interface.

a. Press Setting or Setup (soft button) on the SIP phone.

b. Press [#][5][3][4].

c. Select "On" for "Embedded web", then press [ENTER].

Note

If no operation are made for 30 minutes, the port will be closed again automatically.

4. Access the Web user interface from the PC.

a. Open your Web browser, and then enter "http://"followed by the SIP phone’s IP address into the

address field of your browser.

b. For authentication, enter your ID and password, and then click OK.

The Installer Level ID and Password are as follows.

ID: instoperatoruserid

Password: instpass

c. Select Maintenance ® Import Configuration File.

d. Click Browse… , and then select the configuration file (UT_ACS.cfg).

e. Click Import.

When the configuration file is successfully imported, the SIP phone starts to access the PBX

automatically.

178 Installation Manual

5.8.1 Assigning IP Addressing Information

5. Confirm if the configuration file was successfully loaded.

a. Select Maintenance ® Export Configuration File.

b. Click Export to download the configuration file being used currently on the SIP phone.

c. Compare the UT_ACS.cfg file and the downloaded file. If the UT_ACS.cfg file was successfully loaded,

the contents of those 2 files will be exactly the same.

Notice

When the 2 UT_ACS.cfg files do not match, and if the SIP phone does not work properly, contact

an authorised Panasonic Factory Service Centre.

For Non-KX-UT Series SIP Phones

Using a DHCP server (DHCP Server feature or an external DHCP server) to automate the assignment

of IP addressing information

The IP address of the SIP phone, the subnet mask address, and the default gateway address can be assigned

to the SIP phone automatically by the DHCP server.

The PBX’s IP address must be assigned manually on the SIP phone side.

For instructions, refer to the documentation of the SIP phone.

Not using a DHCP server (DHCP Server feature or an external DHCP server) when assigning IP

addressing information

All of the IP addressing information must be assigned manually.

For instructions, refer to the documentation of the SIP phone.

Note

• A SIP phone can only receive IP addressing information from a DHCP server on its own LAN. Therefore,

when SIP phones are located on several LANs, a DHCP server is required on each LAN.

• When the DHCP client function is enabled for SIP phones, simply connect them to the LAN to use the

DHCP server. For details about the DHCP client function setting, refer to the documentation of the SIP

phone.

Installation Manual 179

5.8.1 Assigning IP Addressing Information

5.8.2 Setting VLAN Parameters

To establish voice communications between IP telephones, the primary ports of the IP telephones and the

connected PBX must belong to the same VLAN. Consult your network administrator and obtain the appropriate

VLAN ID.

If you are using an IP telephone equipped with two ports, it is possible to place primary and secondary ports

of the IP telephone on different VLANs by assigning separate VLAN IDs to each port.

Follow the procedure below for all IP-PTs on the network, using appropriate VLAN IDs.

Note

The procedure for SIP phones may vary depending on the type of the SIP phone being used. Refer to the

documentation of your SIP phone for instructions.

KX-NT300 series (except KX-NT321)

Select "VLAN".

ENTER

VLAN ID

ENTER

VLAN Priority

ENTER

Press

"STORE".

STORE

To set the VLAN ID for the primary port

To set the VLAN ID for the secondary port

To end programming

0–7

1–4094Select "Primary port".

ENTER

VLAN ID

ENTER

VLAN Priority

ENTER

1–4094

Select

"Secondary port (TO PC)".

Select "VLAN Priority".

ENTER

Return to the

VLAN setting screen.

ENTER

Select

"VLAN Priority".

ENTER

Return to the

Menu screen.

Select "Enable" for

VLAN setting.

Select "VLAN ID".

0–7

After assigning

the IP addresses

Select "QoS".

ENTER

The IP-PT will reboot

and can then be

registered to the PBX.

The VLAN priority of the primary port must be set higher than the priority of the secondary port. The larger the number, the higher

the priority.

180 Installation Manual

5.8.2 Setting VLAN Parameters

KX-NT321

To end programming

After assigning

the IP addresses

Select "QoS". Press SP-PHONE. Select "VLAN". Press SP-PHONE.

Press STORE.

Press HOLD three

times to return to the

Menu screen.

Select "VLAN (Enable)".

Press SP-PHONE.

VLAN ID

VLAN Priority

To set the VLAN ID for the primary port

0–7

1–4094

Select "Priority".

Select "VLAN (Primary)". Press SP-PHONE. Press SP-PHONE.

Select "VLAN ID".

Press SP-PHONE.

To set the VLAN ID for the secondary port

VLAN ID

VLAN Priority

1–4094

0–7

Select "VLAN (Secondary)".

Press SP-PHONE. Select "VLAN ID".

Select "Priority".

Press SP-PHONE.

The IP-PT will reboot

and can then be

registered to the PBX.

The VLAN priority of the primary port must be set higher than the priority of the secondary port. The larger the number, the higher

the priority.

Installation Manual 181

5.8.2 Setting VLAN Parameters

KX-NT265 (Software version 2.00 or later only)

VLAN ID

VLAN Priority

To end programming

0–71–4094

After assigning

the IP addresses

Press VOLUME to

select "VLAN".

VOL

Press VOLUME to

select "QoS".

VOL

Press SP-PHONE.Press SP-PHONE. Press VOLUME to

select "VLAN (Enable)".

VOL

Press SP-PHONE.Press SP-PHONE. Press SP-PHONE.

Press STORE.

Press HOLD to return

to the Menu screen.

HOLD

The IP-PT will reboot

and can then be

registered to the PBX.

182 Installation Manual

5.8.2 Setting VLAN Parameters

5.8.3 Setting Diffserv Parameters

Differentiated Services (DiffServ, or DS) is an IP-based QoS technique used to control QoS of VoIP

communications by setting the DS field in the header of IP packets. Consult your network administrator for the

appropriate setting values for the DS field.

Follow the procedure below to set the Diffserv parameters. Only KX-NT300 series IP-PTs and KX-NT265

IP-PTs can be used to set the parameters.

KX-NT300 series (except KX-NT321)

Select "Diffserv".

ENTER

To set the DS field value for the primary port

To set the DS field value for the secondary port

To end programming

Select "Primary Port".

ENTERENTER

Diffserv

0.0–7.7

Return to the

Diffserv setting screen.

ENTER

Return to the

Menu screen.

ENTER ENTER

Select "Enable".

ENTER

Select

"Secondary Port (TO PC)".

Select "Enable".

Press

"STORE".

STORE

Diffserv

0.0–7.7

To start programming

Select "Qos".

ENTER

Press

"SETUP"

when it is displayed.

SETUP

The IP-PT will reboot

and can then be

registered to the PBX.

Installation Manual 183

5.8.3 Setting Diffserv Parameters

KX-NT321

To set the DS field value for the primary port

To set the DS field value for the secondary port

To start programming

Press PROGRAM while

"Searching" is displayed.

Select "QoS". Select "Diffserv".

To end programming

Press STORE.

Press HOLD to return

to the Menu screen.

Select "Primary Port".

Diffserv

0.0–7.7

Press SP-PHONE. Press SP-PHONE.

Select "DS (Enable)".Press SP-PHONE. Press SP-PHONE.

Press SP-PHONE.

Press HOLD to return to

the Diffserv setting screen.

Select "Secondary Port". Select "DS (Enable)".Press SP-PHONE.

Press SP-PHONE.

Diffserv

0.0–7.7

The IP-PT will reboot

and can then be

registered to the PBX.

184 Installation Manual

5.8.3 Setting Diffserv Parameters

KX-NT265 (Software version 2.00 or later only)

To set the DS field value

To start programming

Press PROGRAM while

"Searching" is displayed.

PROG.

Press VOLUME to

select "QoS".

VOL

Press SP-PHONE. Press VOLUME to

select "Diffserv".

VOL

Press SP-PHONE.

To end programming

Press STORE.

Press HOLD to return

to the Menu screen.

HOLD

Press VOLUME to

select "DS (Enable)".

VOL

Press SP-PHONE.

Diffserv

0.0–7.7

Press SP-PHONE.

The IP-PT will reboot

and can then be

registered to the PBX.

Installation Manual 185

5.8.3 Setting Diffserv Parameters

5.8.4 Configuration of IP Ports

A KX-NT300 series IP-PT user or KX-NT265 IP-PT user can configure the port number of PTAP, DHCP, and

FTP ports. Consult your network administrator to check whether the configuration of the IP ports is required.

Follow the procedure below to configure the port number of the IP ports.

KX-NT300 series (except KX-NT321)

Select "IP Port".

ENTER 7678 ENTER

ENTER

1024

–

65535

Port No.

Password

To configure the port number of PTAP Ports

To start programming

Select "PTAP Server Port".

Select "Primary PBX".

Select "Secondary PBX".

To configure the port number of DHCP Ports

ENTER

1024

–

65535

ENTER

Port No.

Select

"PTAP Client Port".

ENTER 67, 1024

–

65535 ENTER

Port No.

Select "DHCP Server Port".

ENTER 68, 1024

–

65535 ENTER

Port No.

Select "DHCP Client Port".

Press

"SETUP"

when it is displayed.

SETUP

Continued on next page

1024

–

65535

Port No.

To configure the port number of PTAP Ports for the Secondary PBX (optional for

software version 2.00 or later only)

Software version 2.00 or later only

Return to the

Menu screen.

186 Installation Manual

5.8.4 Configuration of IP Ports

Press

"STORE".

STORE

To configure the port number of FTP Ports

To end programming

ENTER 21, 1024

–

65535 ENTER

Port No.

Select "FTP Server Ctrl Port".

ENTER 1024

–

65535 ENTER

Port No.

Select "FTP Client Ctrl Port".

1024

–

65535ENTER ENTER

Port No.

Select "FTP Client Data Port".

Return to the

Menu screen.

Continued from previous page

The IP-PT will reboot

and can then be

registered to the PBX.

Installation Manual 187

5.8.4 Configuration of IP Ports

KX-NT321

To configure the port number of PTAP Ports

To configure the port number of DHCP Ports

To start programming

Press PROGRAM while

"Searching" is displayed.

Select "IP Port".

Select "PTAP Server".

7678

Password

1024

–

65535

Port No.

Select "PTAP Client".

Select "DHCP Server".

Select "DHCP Client".

Press SP-PHONE. Press SP-PHONE.

Select "Primary PBX".Press SP-PHONE. Press SP-PHONE.

1024

–

65535

Port No.

Press SP-PHONE. Press SP-PHONE.

67, 1024

–

65535

Port No.

Press SP-PHONE.

68, 1024

–

65535

Port No.

Press SP-PHONE. Press SP-PHONE.

Press SP-PHONE.

Select "PTAP Server".

1024

–

65535

Port No.

Select "Secondary PBX".Press SP-PHONE. Press SP-PHONE.

Press SP-PHONE.

Continued on next page

To configure the port number of PTAP Ports for the Secondary PBX (if required)

Press HOLD.

188 Installation Manual

5.8.4 Configuration of IP Ports

Continued from previous page

To end programming

Press STORE.

Press HOLD to return

to the Menu screen.

To configure the port number of FTP Ports

Select "FTP Server Ctrl".

21, 1024

–

65535

Port No.

Select "FTP Client Ctrl".

1024

–

65535

Port No.

Select "FTP Client Data".

1024

–

65535

Port No.

Press SP-PHONE.

The IP-PT will reboot

and can then be

registered to the PBX.

Installation Manual 189

5.8.4 Configuration of IP Ports

KX-NT265 (Software version 2.00 or later only)

To configure the port number of PTAP Ports

To configure the port number of DHCP Ports

To configure the port number of FTP Ports

To start programming

Press PROGRAM while

"Searching" is displayed.

PROG.

Press VOLUME to

select "IP Port".

VOL

Press SP-PHONE. Press SP-PHONE.

To end programming

Press STORE.

Press HOLD to return

to the Menu screen.

HOLD

Press VOLUME to

select "PTAP Server".

VOL

Press SP-PHONE. Press SP-PHONE.

7678

Password

1024

–

65535

Port No.

Press VOLUME to

select "PTAP Client".

VOL

Press SP-PHONE. Press SP-PHONE.

1024

–

65535

Port No.

Press VOLUME to

select "DHCP Server".

VOL

Press SP-PHONE. Press SP-PHONE.

67, 1024

–

65535

Port No.

Press VOLUME to

select "DHCP Client".

VOL

Press SP-PHONE. Press SP-PHONE.

68, 1024

–

65535

Port No.

Press VOLUME to

select "FTP Server Ctrl".

VOL

Press SP-PHONE. Press SP-PHONE.

21, 1024

–

65535

Port No.

Press VOLUME to

select "FTP Client Ctrl".

VOL

Press SP-PHONE. Press SP-PHONE.

1024

–

65535

Port No.

Press VOLUME to

select "FTP Client Data".

VOL

Press SP-PHONE. Press SP-PHONE.

1024

–

65535

Port No.

The IP-PT will reboot

and can then be

registered to the PBX.

190 Installation Manual

5.8.4 Configuration of IP Ports

Note

If you wish to change the port number back to default, enter 0 as the port number for the desired port.

Installation Manual 191

5.8.4 Configuration of IP Ports

5.9 Registering IP Telephones

5.9.1 Registering IP Telephones

After the programming of the PBX and IP telephones is finished (refer to "5.8 Assigning Networking Information

to IP Telephones"), the IP telephones must be registered to the PBX. The procedure for registering IP

telephones differs according to the IP terminal registration mode specified during the Easy Setup Wizard. This

setting can also be changed in the Site Property—Main screen of the Web Maintenance Console (refer to

"9.5.1 PBX Configuration—Configuration—Slot—Site Property—Main—Main—

IP Terminal Registration

Mode" in the PC Programming Manual). Refer to the following table:

IP Terminals

IP Terminal Registration Mode

Full Automatic Mode

Extension Number

Input Mode

Manual Mode

IP-PTs

ü ü ü

KX-UT Series SIP

Phones

ü ü

Non-KX-UT series SIP

phones

IP-CSs

ü: Available

KX-UT series SIP phones will be registered automatically, in the same way as Full Automatic mode.

Non-KX-UT series SIP phones must always be registered to the PBX manually, even if Full Automatic mode or Extension Number

Input mode is selected.

IP-CSs must always be registered to the PBX manually. For details about registering IP-CSs, refer to the Quick Installation Guide for

the IP-CS.

Note

• For KX-UT series SIP phones, the SIP extension password is automatically set to "1234".

• For IP softphones, follow the same registration procedure as IP-PTs.

Full Automatic Mode

If networking settings have been completed, when IP-PTs or KX-UT series SIP phones are connected to the

same network as the PBX, they will be registered automatically. No registration procedure is required.

Extension Number Input Mode

For IP-PTs

If networking settings have been completed, when IP-PTs are connected to the same network as the PBX,

they will be registered automatically, but extension numbers for the IP-PTs will not be set. Follow the procedure

below to register an extension number to complete registration.

1. After completing networking settings, connect the IP-PT to the same network as the PBX. The screen to

enter the extension number is displayed on the IP-PT.

192 Installation Manual

5.9.1 Registering IP Telephones

2. Enter an extension number.

Note

When no extension number is entered in this step, the process will time out and the IP-PT will be

registered without an extension number.

3. Press [ENTER] on the IP-PT.

4. Press [PAUSE] or "EXIT" on the IP-PT.

For KX-UT Series SIP Phones

If networking settings have been completed, when KX-UT series SIP phones are connected to the same

network as the PBX, they will be registered automatically as same as when they are registered in Full Automatic

mode. No registration procedure is required.

Note

No more than 64 IP-PTs can register extension numbers at the same time.

Manual Mode

For IP-PTs or KX-UT Series SIP Phones

After connecting IP-PTs or KX-UT series SIP phones to the PBX over a network, register those IP terminals

to the PBX manually.

Follow the procedure below for registration.

a. Click Setup ® PBX Configuration ®

Configuration ® Slot.

b. For IP-PTs:

Click Virtual ® V-IPEXT32.

For KX-UT series SIP phones:

Click Virtual ® V-UTEXT32.

c. For IP-PTs:

Move the mouse pointer over the V-IPEXT32 card

(Virtual 32-Channel VoIP Extension Card).

For KX-UT series SIP phones:

Move the mouse pointer over the V-UTEXT32 card

(Virtual UT Extension Card).

A menu will be shown under the mouse pointer.

d. Click Port Property.

To register the IP-PT or KX-UT series SIP phone by entering the MAC address directly:

Installation Manual 193

5.9.1 Registering IP Telephones

2. If the Connection column for the port is INS, click INS,

and then click OUS on the dialogue box to change the

port’s status.

3. Enter the MAC address of the IP-PT or SIP phone in the

IP Phone Registration ID (MAC Address) cell.

4. Click Apply.

Once the IP-PT or SIP phone is successfully registered,

its status will update to show "Registered".

5. In the Connection column for the port, click OUS, and

then click INS on the dialogue box to change the port’s

status.

6. For KX-UT series SIP phones only:

Follow the procedure below to change the IP Terminal

Registration Mode from Manual to Full Automatic.

a. Click Setup ® PBX Configuration ®

Configuration ® Slot ® Site Property ® Main.

b. In the Main tab, select Full Automatic for IP

Terminal Registration Mode.

c. Click OK.

To register the IP-PT or KX-UT series SIP phone using the wizard:

2. Click Registration.

A dialogue box will appear. Non-registered (available)

extension numbers and names are displayed on the left.

a. Highlight numbers and names and click the right

arrow to select them for registration, and then click

Next.

b. Click Next. A screen will appear with information on

the current IP-PT or SIP phone extension number

and name, and index number for programming.

Note

• If the IP-PT or SIP phone has been

connected to the LAN and power has been

turned on, the IP address of the PBX will be

assigned automatically.

• If not, connect the IP-PT or SIP phone to the

LAN and turn the power on within 15 minutes

after this operation is done. The IP address

of the PBX will then be assigned

automatically.

c. If the registration is still in progress, the dialogue box

will show "Registration Executing".

If the registration is successful, the dialogue box will

show "Registration Completed". Click Close.

Once the IP-PT or SIP phone is successfully

registered, its status will update to show

"Registered".

194 Installation Manual

5.9.1 Registering IP Telephones

For Non-KX-UT Series SIP Phones

After connecting non-KX-UT series SIP phones to the PBX over a network, register those IP terminals to the

PBX manually.

Follow the procedure below for registration.

a. Click Setup ® PBX Configuration ®

Configuration ® Slot.

b. Click Virtual ® V-SIPEXT32.

c. Move the mouse pointer over the V-SIPEXT32 card

(Virtual 32-Channel SIP Extension Card).

A menu will be shown under the mouse pointer.

d. Click Port Property.

2. Assign extension numbers to the SIP extensions.

• If the Automatic Extension Number Set for Extension

Card feature is enabled, the extension numbers of

SIP extension are automatically assigned. To

programme this feature, refer to "9.30 PBX

Configuration—Configuration—Option— New

Card Installation—Automatic Extension Number Set

for Extension Card" in the PC Programming Manual.

• If not, enter the extension number for each SIP

extension manually.

Installation Manual 195

5.9.1 Registering IP Telephones

3. Set passwords for the SIP extensions.

a. Click the cell in the Connection column for each SIP

extension you wish to register. The Command

Connection screen appears.

b. Click OUS.

c. Enter a password in the Password cell for each SIP

extension.

d. Click Apply.

e. Click the cell in the Connection column for each SIP

extension to which a password has been assigned.

The Command Connection screen appears.

f. Click INS.

g. Click OK.

Note

• Alternatively, it is possible to set an extension

number as a password for each SIP extension

automatically.

• In order to set the password automatically, do

the following in substitution for step c of the

procedure above.

a. Click Copy to. A screen will appear with

information on assigned extension numbers

for SIP extensions.

b. Click Select All.

c. Click Execute to copy each Extension

Number to Password.

d. Click Yes.

e. Click OK to return to the Port Property

screen.

• When copying extension numbers to

passwords, you can also use the icon on the

bottom left of the Virtual SIP Extension Port

Property screen.

196 Installation Manual

5.9.1 Registering IP Telephones

4. Programme the SIP extension you wish to register.

a. Set the IP address of the PBX, extension number,

and password in the corresponding fields for your

SIP extension.

b. Send a request from the SIP extension to the PBX

for registration.

• If the authentication information of the SIP

extension and the PBX match, the registration is

successful.

Note

• When programming the SIP extension, the

names of the corresponding fields may differ

depending on the type of SIP phone you are

using.

• For details about the actual operation of SIP

phones, refer to the documentation of the SIP

phone.

• For certain SIP phones, you may need to set a

Sign-in name, which should consist of the

extension number and the IP address of the PBX

(e.g., [email protected]).

Installation Manual 197

5.9.1 Registering IP Telephones

5.9.2 De-registering IP Telephones

De-registration of IP-PTs or KX-UT Series SIP Phones

1. Make sure the IP Terminal Registration Mode is set to

Manual.

a. Click Setup ® PBX Configuration ®

Configuration ® Slot ® Site Property ® Main.

b. In the Main tab, select Manual for IP Terminal

Registration Mode.

c. Click OK.

a. Click Setup ® PBX Configuration ®

Configuration ® Slot.

b. For IP-PTs:

Click Virtual ® V-IPEXT32.

For KX-UT series SIP phones:

Click Virtual ® V-UTEXT32.

c. For IP-PTs:

Move the mouse pointer over the V-IPEXT32 card

(Virtual 32-Channel VoIP Extension Card).

For KX-UT series SIP phones:

Move the mouse pointer over the V-UTEXT32 card

(Virtual UT Extension Card).

A menu will be shown under the mouse pointer.

d. Click Port Property.

3. Click De-registration.

A dialogue box will appear. Registered extension

numbers and names are displayed on the left.

a. Highlight numbers and names and click the right

arrow to select them for de-registration.

b. Click Next.

A dialogue box will appear.

c. Click Confirm.

• If the de-registration is successful, the dialogue

box will show "De-registration succeed!".

d. Click Close.

Once the IP-PT or SIP phone is successfully de-registered, the status of the IP telephone will update to show

"None".

198 Installation Manual

5.9.2 De-registering IP Telephones

Forced De-registration of IP-PTs or KX-UT Series SIP Phones

Follow the steps below to forcibly de-register an IP-PT when normal de-registration was unsuccessful.

a. Click Setup ® PBX Configuration ®

Configuration ® Slot.

b. For IP-PTs:

Click Virtual ® V-IPEXT32.

For KX-UT series SIP phones:

Click Virtual ® V-UTEXT32.

c. For IP-PTs:

Move the mouse pointer over the V-IPEXT32 card

(Virtual 32-Channel VoIP Extension Card).

For KX-UT series SIP phones:

Move the mouse pointer over the V-UTEXT32 card

(Virtual UT Extension Card).

A menu will be shown under the mouse pointer.

d. Click Port Property.

2. Click Forced De-registration.

A dialogue box will appear. Registered extension

numbers and names are displayed on the left.

a. Highlight numbers and names and click the right

arrow to select them for de-registration.

b. Click Next.

A dialogue box will appear.

c. Click OK.

A dialogue box will appear.

d. Click Confirm.

• If the de-registration is successful, the dialogue

box will show "Forced de-registration succeed!".

e. Click Close.

Once the IP-PT or SIP phone is successfully de-registered, the status of the IP telephone will update to show

"None".

Installation Manual 199

5.9.2 De-registering IP Telephones

De-registration of Non-KX-UT Series SIP Phones

The de-registration of non-KX-UT series SIP phones is carried out by deleting either the extension number or

password registered in the PBX.

a. Click Setup ® PBX Configuration ®

Configuration ® Slot.

b. Click Virtual ® V-SIPEXT32.

c. Move the mouse pointer over the V-SIPEXT32 card

(Virtual 32-Channel SIP Extension Card).

A menu will be shown under the mouse pointer.

d. Click Port Property.

a. Click the cell in the Connection column for the port

of the SIP phone to de-register.

b. In the Command window, click OUS to change the

status of the port to "OUS".

3. Repeat step 2 for each SIP phone to de-register.

4. Delete either the extension number or password for the

SIP phone to de-register, as shown here.

5. Click OK.

200 Installation Manual

5.9.2 De-registering IP Telephones

5.10 Configuration of Users

The system manages information about each user.

Before programming other user settings, the following information must be configured for each user:

• Extension number

• Name

• Unified Messaging mailbox

• Web Maintenance Console login account (ID and password)

Follow the procedure below to efficiently programme basic personal information by adding multiple users with

the Add Range feature.

1. Click Setup ® PBX Configuration ® Configuration ® Slot.

Add one or more extension cards to the system, according to your equipment and needs. Extension

numbers will be automatically created for each extension card that is added. For details about adding

extension cards, refer to "9.1 PBX Configuration—Configuration—Slot" in the PC Programming Manual.

2. Click Setup ® PBX Configuration ® Extension.

Enter an extension name for each extension number to be used. For details, refer to the following sections

in the PC Programming Manual:

• 12.1.1 PBX Configuration—Extension—Wired Extension—Extension Settings

• 12.2.1 PBX Configuration—Extension—Portable Station—Extension Settings

Note

You also can import extension names from a CSV file. For details refer to "6.6 Tool—Import" in the

PC Programming Manual.

3. Click Setup ® Users ® User Profiles.

You can create multiple user profiles automatically by using the Add Range feature for extension numbers.

You can also set an extension number, first name, last name, Unified Messaging mailbox, and Web

Maintenance Console login account for each user manually.

For details, refer to "User Controls" in "8.1 Users—User Profiles" in the PC Programming Manual.

For each user profile added using the Add Range feature, the following information is automatically

assigned:

• First Name: "Ext." + the extension number for the user (e.g., "Ext.101")

• Last Name: The information entered in Extension Name for the extension in the Extension screen

• Login ID: The extension number (i.e., if the extension is "101", the Login ID for the user will also be

"101")

• Password: "PWD" + the extension number for the user (e.g., "PWD101")

4. If additional editing is required for users, settings can be configured on the following screens:

a. To edit user information: Setup ® Users ® User Profiles

b. To edit extension settings: Setup ® PBX Configuration ® Extension

c. To edit mailbox settings: Setup ® UM Configuration ® Mailbox Settings

Note

You also can create mailboxes for Incoming Call Distribution Groups on the Mailbox Settings

screen.

Installation Manual 201

5.10 Configuration of Users

202 Installation Manual

5.10 Configuration of Users

Section 6

Troubleshooting

This section provides information on the PBX and

telephone troubleshooting.

Installation Manual 203

6.1 Troubleshooting

6.1.1 Installation

PROBLEM PROBABLE CAUSE SOLUTION

You cannot make/receive

calls via an IP network.

• DSP card malfunction • Replace the corresponding card.

• Mother board

malfunction

• Replace the mother board (be sure to turn

off the PBX when replacing).

• Not enough activation

keys

• Purchase additional activation key codes.

Please consult a certified dealer for

details.

• Poor connection • Make sure that an 8-pin twisted pair cable

is used for connection.

• Make sure that none of the CAT 5/CAT 5e

cables in use are over 100 m in length.

• Make sure that a straight cable is used for

connection to a switching hub.

• Network malfunction • Make sure that all network devices in use

are switched on.

• Make sure that there is no unwanted

firewall in the IP network.

IP-PTs/SIP phones do not

operate.

• DSP card malfunction • Replace the corresponding card.

• Mother board

malfunction

• Replace the mother board (be sure to turn

off the PBX when replacing).

• Not enough activation

keys

• Purchase additional activation key codes.

Please consult a certified dealer for

details.

• IP-PT/SIP phone not

registered

• Register the corresponding IP-PT/SIP

phone.

• IP-PT/SIP phone

malfunction

• Replace the IP-PT/SIP phone.

• Poor connection • Make sure that an 8-pin twisted pair cable

is used for connection.

• Make sure that none of the CAT 5/CAT 5e

cables in use are over 100 m in length.

• Make sure that a straight cable is used for

connection to a switching hub.

• Network malfunction • Make sure that all network devices in use

are switched on.

• Make sure that the IP-PT/SIP phone is not

blocked by the firewall or other network

devices.

204 Installation Manual

6.1.1 Installation

PROBLEM PROBABLE CAUSE SOLUTION

Extensions (except IP-PT/

SIP phone) do not operate.

• Extension card

malfunction

• Replace the corresponding card.

• Poor connection

between the PBX and

the extension

• Take the extension and plug it into the

same extension port using a short

telephone cord. If the extension works,

then the connection between the PBX and

the extension must be repaired.

• A telephone with an

A-A1 relay is

connected.

• Make sure that a 2-wire cord is used.

• Make sure that the A-A1 relay switch of

the telephone is in "OUT" or "OFF"

position.

• Extension malfunction • Take the extension and plug it into

another extension port that is working. If

the extension does not work, replace the

extension.

The PBX does not operate

properly.

• Restart the PBX (refer to

"6.1.5 Restarting the PBX").

• Turn off the power switch, and then turn it

back on.

• Turn off the power switch, and then

unplug the PBX. After 5 minutes, plug the

PBX back in, and turn the power switch

back on.

Noise on external paging.

• Induced noise on the

wire between the PBX

and the amplifier.

• Use a shielded cable as the connection

wire between the PBX and amplifier. A

short shielded cable is recommended.

Distorted external music.

• Excessive input level

from external music

source.

• Decrease the output level of the external

music source by using the volume control

on the music source.

The STATUS indicator on

the front of the cabinet turns

on red.

• A major system error

occurs in the PBX.

• See the error log using Web Maintenance

Console (refer to "6.1.6 Troubleshooting

by Error Log").

The LINK indicator of the

mother board does not turn

on.

• Mother board

malfunction

• Replace the mother board (be sure to turn

off the PBX when replacing).

• Poor connection. • Make sure that an 8-pin twisted pair cable

is used for connection.

• Make sure that none of the CAT 5/CAT 5e

cables in use are over 100 m in length.

• Make sure that a straight cable is used for

connection to a switching hub.

• Network malfunction • Make sure that all network devices in use

are switched on.

Installation Manual 205

6.1.1 Installation

6.1.2 Connection

Connection between the trunk and the PBX:

CAUSE

Trunk is connected to the T2/T1.

SOLUTION

Reconnect the trunk to

the T1/R1 or T2/R2 of the

telephone jack using 2-

conductor wiring.

Trunk PBX

Trunk is connected to the T2/R1.

PBX

Trunk

Can you dial

out on a

trunk?

Can you dial

an extension?

Connection between the PBX and an SLT that is polarity-sensitive:

PBX

CAUSE

The "T" is connected to the "R".

SOLUTION

Extension

Reverse the connections of

the T/R.

Yes

Connection between the PBX and an SLT:

CAUSE SOLUTION

If a telephone equipped

with an A-A1 relay is

connected to the PBX, set

the A-A1 relay switch of the

telephone to "OFF".

Use the correct cord (the

inner 2 wires are for T/R).

PBX

The T/R is connected to the D1/D2.

Extension

206 Installation Manual

6.1.2 Connection

6.1.3 Operation

PROBLEM PROBABLE CAUSE SOLUTION

• Cannot set the IP

address, subnet mask

address, and PBX IP

address to the IP-PT.

• An unusable value is

being set.

• Set an IP address within the valid range.

IP address of the IP-PT/PBX: "1.0.0.0" to

"223.255.255.255" Subnet mask address:

"0–255.0–255.0–255.0–255" (except

"0.0.0.0" and "255.255.255.255")

• Cannot register the

IP-PT.

• The necessary network

parameters are not set

to the IP-PT.

• When not using the DHCP Server feature

or an external DHCP server, set the IP

address, subnet mask address, and enter

the PBX IP address. If necessary, also

enter the IP address of the default

gateway.

• When using the DHCP Server feature or

an external DHCP server, enter the PBX

IP address.

• The IP-PT cannot

connect to the PBX.

• The wrong IP address,

subnet mask address,

PBX IP address, or

default gateway

address was entered.

• Check each parameter and enter the

correct value.

• The Ethernet cable is

not connected

correctly.

• Check the Ethernet cable connections.

• The DHCP server is not

active.

• Restart the external DHCP server.

• Confirm whether the DHCP Server feature

is enabled.

• Disable DHCP and re-enter settings as

appropriate.

• Whenever you try to

make calls using a SIP

phone, a busy tone is

heard.

• The status of the port

that the SIP phone is

connected to is Out of

Service.

• Change the port status from Out of

Service to In Service using Web

Maintenance Console.

• The IP-PT does not

ring.

• The ringer volume is off. • Turn on the ringer volume.

• Originating an outside

call, call transfer, or

conference cannot be

performed.

• The corresponding

flexible button does not

exist on the PT.

• Programme the flexible button. Refer to

"2.21.1 Fixed Buttons" in the Feature

Guide.

Installation Manual 207

6.1.3 Operation

PROBLEM PROBABLE CAUSE SOLUTION

• The IP address of the

PBX for networking has

been forgotten.

• Connect a PC to the MNT port of the PBX

directly and start the Web Maintenance

Console using the default IP address of

the MNT port, and then confirm the IP

address assigned for the LAN port.

For details of connecting the PC directly to

the PBX, refer to "5.2 PC Connection".

For details of checking current IP address

of the mother board, refer to

"27.1 Network Service—IP Address/Ports

— LAN Setting—IP Address" in the PC

Programming Manual.

208 Installation Manual

6.1.3 Operation

6.1.4 Error Messages

When a major system error occurs, an error message is displayed on the IP-PT.

For IP-PTs with a single line display (e.g., KX-NT265), only an error code (i.e., ERR XXXX-XXXX) will be

displayed.

Error Message & IP-PT Activity Probable Cause Solution

ERR 1001-0000

HARDWARE ERROR

Displays error and stops operating.

• Sub CPU malfunction • Repair or replace the

IP-PT.

ERR 1002-0000

HARDWARE ERROR

Displays error and stops operating.

• Sound hardware

malfunction

ERR 1003-0000

HARDWARE ERROR

Displays error and stops operating.

• Flash memory malfunction

ERR 1004-XXXX

HARDWARE ERROR

Displays error and stops operating.

• PHY (network control IC)

error

ERR 1005-0000

HARDWARE ERROR

Displays error and stops operating.

• SDRAM error

ERR 1006-0000

HARDWARE ERROR

Displays error and stops operating.

• SRAM error

ERR 1007-0000

HARDWARE ERROR

Displays error and stops operating.

• Sub CPU malfunction for

Self Labelling

ERR 1051-0000

SOFTWARE ERROR

Displays error and stops operating.

• PBX software version error • Consult your network

administrator.

ERR 2001-XXXX

SYSTEM ERROR

Resets and displays error for 5 seconds

while starting up.

• Unexpected error • If this error is displayed

frequently, repair or

replace the IP-PT.

ERR 2002-0000

POOR LAN CONNECTION

Resets and displays error for 5 seconds

while starting up.

• Transmission error • Check with the network

administrator whether

there is a problem with the

LAN.

• If this error is displayed

frequently, repair or

replace the IP-PT.

ERR 2003-0000

POOR LAN CONNECTION

Resets and displays error for 5 seconds

while starting up.

Installation Manual 209

6.1.4 Error Messages

Error Message & IP-PT Activity Probable Cause Solution

ERR 2004-0000

UNREGISTERED TO SERVER

Resets and displays error for 5 seconds

while starting up.

• IP-PT not registered • Check the registration

status of the IP-PT.

ERR 2005-0000

NO MORE CONNECTIONS

Resets and displays error for 5 seconds

while starting up.

• Connection refused by the

PBX

ERR 2006-XXXX

DHCP SERVER REJECTION

Resets and displays error for 5 seconds

while starting up.

• IP address lease time from

DHCP server has expired

• IP address lease renewal

was refused by DHCP

server

• Consult your network

administrator.

ERR 2007-0000

HARDWARE ERROR

Resets and displays error for 5 seconds

while starting up.

• Communication error with

sub CPU

• If this error is displayed

frequently, repair or

replace the IP-PT.

ERR 2008-0000

HARDWARE ERROR

Resets and displays error for 5 seconds

while starting up.

• Sound hardware control

error

ERR 2009-XXXX

MGCP SERVER REJECTION

Resets and displays error for 5 seconds

while starting up.

• Error information from the

PBX (MGCP server)

• Consult your network

administrator.

ERR 2010-0000

HARDWARE ERROR

Resets and displays error for 5 seconds

while starting up.

• Communication error with

sub CPU for Self Labelling

• If this error is displayed

frequently, repair or

replace the IP-PT.

ERR 3001-0000

HARDWARE ERROR

Displays error until reset the IP-PT.

• Communication error with

sub CPU

ERR 3002-0000

HARDWARE ERROR

Displays error until reset the IP-PT.

• Sound hardware control

error

ERR 3003-XXXX

DHCP SERVER NOT FOUND

Displays error until reset the IP-PT.

• IP address lease renewal

was refused by DHCP

server

• Consult your network

administrator.

ERR 3100-0000

BLUETOOTH ERROR

Resets the Bluetooth

wireless

headset.

• Bluetooth hardware error • Repair or replace the

Bluetooth wireless

headset.

210 Installation Manual

6.1.4 Error Messages

6.1.5 Restarting the PBX

If the PBX does not operate properly, restart the PBX using Web Maintenance Console. Before restarting the

PBX, try the system feature again to confirm whether there definitely is a problem or not.

Note

• When the System Mode Switch is set to "NORMAL", restarting the PBX causes the following:

– Camp-on is cleared.

– Calls on hold are terminated.

– Calls on exclusive hold are terminated.

– Calls in progress are terminated.

– Call park is cleared.

Other data stored in memory, except the above, are not cleared.

• Be aware that restarting the PBX with the System Mode Switch in the "SYSTEM INITIALIZE" position

clears all data stored in the PBX. Do not perform this operation unless you intend to delete all data

from the PBX.

• When the PBX is set to obtain IP addressing information automatically, and the PBX is not able to

obtain appropriate IP addressing information from an external DHCP server, the PBX starts up with its

default IP addresses and the STATUS indicator on the front of the cabinet turns red. For the default IP

addresses, refer to "5.3 Starting Web Maintenance Console".

Operation

If the PBX does not operate properly:

1. Slide the System Mode Switch to the "NORMAL" position.

System Mode Switch

2. Start the Web Maintenance Console.

3. Log in using the Installer level account.

4. On the Home screen, click Maintenance ® System Control ® System Reset.

5. Follow the prompts.

Restarting the PBX will start.

Note

• When the power switch is turned on, or when the PBX is recovers from a power failure, the PBX will

restart. The time required to restart depends on the number of connected extensions and the number

of registered One-look network sites.

Installation Manual 211

6.1.5 Restarting the PBX

Example:

PBX Extensions Estimated Time for Starting Up

1 PBX

(Stand-alone)

128 KX-UT series SIP phones more than 5 minutes

16 PBXs

(One-look network)

256 KX-UT series SIP phones more than 15 minutes

• PBX functions cannot be used until restarting is complete. The use of a UPS is recommended; even

a momentary power failure can result in a long delay as the PBX restarts, requiring the time as shown

above.

212 Installation Manual

6.1.5 Restarting the PBX

6.1.6 Troubleshooting by Error Log

When a major system error occurs in the PBX, the STATUS indicator on the front of the cabinet turns red, and

the system logs the error information.

Error Log Display Format

Below is the display format of the error log. For information about how to view the error log using Web

Maintenance Console, refer to " Print Information—Error Log" in the PC Programming Manual.

Example: Web Maintenance Console

3 7

124 5 6

Example: Station Message Detail Recording (SMDR)

01/01/10 01:00AM MJ ALM #014 00 10000 FAN Alarm

01/01/10 01:29AM MN ALM #533 01 50401 Unit start up error

01/01/10 01:39AM MN ALM #091 00 10000 PT connection over

123 45 6

Description

Item

Description

1 Date The date of the error detection.

2 Time The time of the error detection.

3 Level Minor (MN ALM) Displays minor errors, which affect only a certain part of system

operation.

Major (MJ ALM) Displays major errors, which affect operation of the whole

system, or result in system failure.

4 Error Code The 3-digit error code assigned by the PBX.

Installation Manual 213

6.1.6 Troubleshooting by Error Log

Item Description

5 Sub Code SMDR:

The 8-digit sub code of the relevant hardware (BBWXYYZZ).

Web Maintenance Console:

The 6-digit sub code of the relevant hardware (WXYYZZ). (The

site number of the PBX can be confirmed in the Site column of

the Error Log.)

• BB: Site ID (00 to 15)

– Corresponds to site numbers of PBXs in the One-look

network (1 to 16)

• W: Slot type

– Physical slot: " " (blank)

– Virtual slot: "*" (asterisk)

• X: (1: Unit number, 5: Other than PBX process code)

When X = 1

• YY: Slot number

– Physical slot: 00 to 05

(00: Mother board slot; 01 to 05: Optional service card

slots)

– Virtual slot: 01 to 52

(01 to 16: Virtual trunk slots; 17 to 52: Virtual extension

slots)

• ZZ: Port number

– For optional service cards:

The port number (01 to XX) will be displayed.

When X = 5

• YY: Process code

• ZZ: Process number (determined by each process)

Note

When there is no parameter for slot and port number, YY

and ZZ will be displayed as "00".

Example: Sub code for the mother board = "01 10000"

6 Error Message A description of the error.

7 Log Information Displays probable causes of the errors and their solutions.

214 Installation Manual

6.1.6 Troubleshooting by Error Log

Section 7

Appendix

This section provides information on using the PBX with

a VoIP network, the ports used by the PBX, and PBX

Region Suffix Codes and Areas.

Installation Manual 215

7.1 Information about Using an IP Network

This section explains common IP network information necessary for setting up One-look networks and QSIG

networks.

7.1.1 Using a VoIP Network with the PBX

This PBX supports Panasonic KX-NT300 series and KX-NT265 IP proprietary telephones (IP-PTs),

Panasonic IP softphones, and SIP (Session Initiation Protocol) phones (hardphones and softphones) for

communication on a Voice over Internet Protocol (VoIP) network. These IP telephones can be used as

extensions of the PBX when the local office LAN is connected to other LANs at different locations.

This PBX also enables VoIP communication with PBXs installed at different locations. Since the communication

does not take place over conventional telephone network, the high cost of long distance communication is

virtually eliminated.

To establish a VoIP network, the virtual cards are used according the requirement of the network. For details

about virtual cards, see "4.4 Virtual Cards".

The following diagrams illustrate VoIP network with (i) a remote office LAN and (ii) another PBX installed at

different location.

Note

Panasonic IP Cell Station (IP-CS) units are also supported by this PBX for communication on a VoIP

network. For details, refer to the Quick Installation Guide for the IP-CS.

(i) Connection Outline of VoIP Network with Remote Office LAN

SIP Phone

Extn. 102

IP-PT

Extn. 101

DHCP Server

Remote Office LAN

Local Office LAN

Router

Switching

Hub

PBX with

V-IPEXT32 card/

V-SIPEXT32 card

IP Softphone

Extn. 103

Private

IP Network

IP-PT

Extn. 104

Switching

Hub

IP Softphone

Extn. 105

Router

SIP Phone

Extn. 106

216 Installation Manual

7.1.1 Using a VoIP Network with the PBX

(ii) Connection Outline of VoIP Network with PBX in Other Network

Private IP Network

Router

Switching Hub

Router

Switching Hub

PBX with

V-IPGW card/

V-SIPGW card

Branch

Headquarters

PBX with

V-IPGW card/

V-SIPGW card

Network Parameters

You will need to have the following IP addressing and QoS information to establish VoIP communication on

your network. This information is typically supplied by a network administrator.

Consult your network administrator for specific values.

Parameter

Description

IP telephone IP Address

Identifies the location of IP telephones on the network. Each IP

telephone must have a unique IP address.

Subnet Mask Address

Defines which digits of an IP address are used for the network

address and the host address at each network location. The IP

addresses of the IP telephones and the PBX must fall within the same

subnet as that of the default gateway (e.g., router) of the LAN.

Default Gateway Address

Identifies the IP address of the primary gateway (typically a router or

similar device) that exchanges IP packets with the other gateways on

the VoIP network.

Installation Manual 217

7.1.1 Using a VoIP Network with the PBX

Parameter Description

PBX IP Address

Identifies the location of the PBX in the network during VoIP

communications.

VLAN ID

Identifies the ID of the logical segment within the corporate LAN,

through which voice packets from IP telephones travel. For details,

refer to "7.1.3 VLAN (Virtual LAN)".

DiffServ (DS)

Identifies the value for the DS field in the header of IP packets, which

determines the priority given to packets travelling from IP telephones.

For details, refer to "5.8.3 Setting Diffserv Parameters".

Types of IP Network

The speech quality depends on the type of IP network in use. Managed IP networks provide better speech

quality compared to unmanaged networks such as satellite communications, where quality of service cannot

be guaranteed.

Examples of recommended IP networks

• Digital Leased Line

• IP-VPN (Virtual Private Network)

• Frame Relay

Not recommended

• Satellite communications (Very Small Aperture

Terminal system [VSAT], etc.)

Note

• Peer-to-peer calls between IP telephones installed at different locations may not be possible if packet

communication cannot be established between the respective networks. In this case, you need to

configure the network settings (e.g., a VPN router when using an IP-VPN) to establish packet

communication.

• Unlike an IP-VPN, which is set up over a network provider’s own IP network, an Internet VPN is set up

over the Internet. Internet VPNs are not recommended for VoIP communication because transmission

delays and loss of data are likely to occur.

• If multiple Slave units exist in a One-look network using IP-VPN, each Slave unit must have

peer-to-peer communication enabled. Therefore, inform your network administrator and make sure that

the network supports this requirement.

218 Installation Manual

7.1.1 Using a VoIP Network with the PBX

7.1.2 DHCP (Dynamic Host Configuration Protocol) Server

To establish communication over a VoIP network, IP addresses must be assigned to IP telephones and the

PBX to identify their locations on the network. While these addresses can be assigned manually, it is also

possible to use a DHCP server to automatically assign IP address information. The KX-NS1000 has a DHCP

Server feature. Therefore, the PBX can act as a DHCP server or DHCP client depending on its settings. When

the PBX’s DHCP Server feature is enabled, it allows you to centrally manage and automate the assignment

of IP addresses with Web Maintenance Console. For details, refer to " DHCP Server" in the PC Programming

Manual.

Assign IP address

information to an IP

telephone

When the mother board is

connected to the network

When an IP telephone is

connected to the network

Request IP address

information

Assign IP address

information to the

DSP cards

Request IP address

information

PBX

(DHCP Server

feature enabled)

DSP Card

IP Telephone

Note

• The DHCP Server feature is disabled by default. To enable the feature, refer to "5.4.2 Enabling the

DHCP Server Feature".

• An IP telephone and the mother board/DSP cards cannot request IP addresses from a DHCP server

on another LAN (connected through an IP network). They can only receive IP addresses from a DHCP

server on the same LAN. Therefore, when IP telephones are located on several LANs, a DHCP server

is required on each LAN. If a DHCP server is not present on the LAN, IP addresses for IP telephones

and the mother board/DSP cards on that LAN must be assigned manually.

• When the PBX has been set to act as a DHCP client, use an external DHCP server to assign IP address

information automatically.

• When the KX-NS1000 is set as the DHCP client and cannot receive appropriate IP addressing

information from an external DHCP server, the PBX keeps using the previous effective IP addressing

information and checks whether any overlapping of IP addresses exists. If the IP address of the PBX

overlaps with another IP address, the PBX displays a warning to encourage changing the IP address

of the PBX.

Installation Manual 219

7.1.2 DHCP (Dynamic Host Configuration Protocol) Server

7.1.3 VLAN (Virtual LAN)

VLANs are logical segments within a corporate LAN. By assigning VLAN settings to IP telephones, it is possible

to separate the packets transmitted by an IP telephone according to the type of data and specify which VLAN

each data type will be sent over. This allows you to avoid generating unnecessary network traffic on each

segment and to reduce the load on the network. As a consequence, speech quality can be assured. Therefore,

we recommend using the VLAN feature to perform VoIP communication effectively.

Some IP telephones (e.g., KX-NT300 series) are equipped with 2 ports, primary and secondary, for packet

communication. Allocating these ports to different VLANs enables you to split the paths for packets depending

on whether the packet contains voice signals or data.

VLAN settings (VLAN ID and VLAN priority) for the primary port affect voice data transmitted by the IP

telephone, whereas VLAN settings for the secondary port apply to data transmitted by a PC connected to the

IP telephone. When sending packets, the IP telephone can attach information on which VLAN the packets are

to be transmitted over (VLAN Tagging). The switching hub that receives these packets reads the VLAN

information and sends the packets over the appropriate VLAN. This helps to ensure bandwidth for IP telephone

voice transmissions.

In this way, an IP telephone with 2 ports can transmit voice packets from the primary port with higher priority

than other packets from the secondary port.

Notice

The PBX’s LAN port does not support VLAN tagging. Therefore, connect the PBX’s LAN port to a port of

the switching hub that is set to "Untagged", and the IP telephone to a port set to "Trunk", to allow VLAN

tagging. Consult your network administrator for details.

PBX

IP Telephone with 2 ports

VLAN 1VLAN 1

VLAN 1

VLAN 2

VLAN 1

Segment for Voice Data

VLAN 2

Segment for Other Data

Voice Packet

Other Packet

VLAN 2

VLAN-capable Switching Hub

Primary Secondary

Untagged

220 Installation Manual

7.1.3 VLAN (Virtual LAN)

Note

• This VLAN feature complies with IEEE (Institute of Electrical and Electronics Engineers) 802.1Q.

• The PBX receives VLAN settings only from the connected switching hub. Therefore, VLAN settings for

the PBX must be assigned at the switching hub.

• When using the VLAN feature on the network, make sure that the main unit is connected to a layer 2

switch that is IEEE 802.1Q compliant, and that is configured for VLANs. In addition, the port of the

switching hub to which the card is connected must be set to "Untagged". Consult your network

administrator for details.

• When using the VLAN feature on the network, make sure that the switching hub to be connected is

IEEE 802.1Q compliant and is configured for VLANs. In addition, the port of a switching hub that the

IP telephone is connected to must be set to "Trunk" port, to allow VLAN tagging. Consult your network

administrator for details.

• Some PC LAN cards allow VLAN settings to be assigned. However, when using a PC connected to an

IP telephone with 2 ports, the VLAN settings for PC communications must be assigned only to the

secondary port of the IP telephone. Any VLAN settings assigned to the PC LAN card must be disabled.

These settings can usually be identified by "802.1Q", "802.1p", or "VLAN" in their name.

• If you are using an IP telephone with a primary port only (e.g., KX-NT265), a PC cannot be connected

to the IP telephone.

7.1.4 Jitter Buffer

When voice signals are packetised and transmitted, individual packets can take different paths through the

network and arrive at the destination at varied timings. This is referred to as "jitter", and it can cause degradation

in speech quality. To compensate for jitter problems, the "jitter buffer" accumulates the packets temporarily for

processing.

To set the size of the jitter buffer, refer to "9.5 PBX Configuration—Configuration—Slot—Site Property—

VoIP-DSP Options" in the PC Programming Manual.

7.1.5 Voice Activity Detection (VAD)

VAD conserves bandwidth by detecting silent periods during a call and suppressing the packets of silence from

being sent to the network. This feature can be enabled or disabled for codec G.711.

To configure the VAD feature, refer to the appropriate section in the PC Programming Manual.

Installation Manual 221

7.1.5 Voice Activity Detection (VAD)

7.1.6 Network Configuration

You must evaluate the structure of the existing network to see if a VoIP network can be implemented. Below

are the points that should be evaluated.

Is the IP network a managed network?

A VoIP network should be implemented on a managed IP network such as Frame Relay, Leased Line, or

IP-VPN (Virtual Private Network).

An unmanaged network, such as the Internet (including an Internet VPN), cannot be used to employ a VoIP

network because delays and loss in data transmission can cause huge degradation in speech quality.

Is it possible to have static IP addressing?

IP telephones on the network always perform VoIP communications through the PBX. Therefore, the PBX

must be assigned static IP addresses, which must be programmed to each IP telephone on the network.

Note

When the DHCP Server feature is disabled and external DHCP servers are not used, static IP addressing

must also be enabled for all IP telephones.

Does only a single router provide access to the IP network?

In a dual network, 2 routers provide access to the IP network as shown in the diagram below. However, only

one router can be used as an access point to the network.

Therefore, in the diagram below, if router A, whose IP address is assigned as the default gateway IP address

of the PBX and the IP telephones, fails, VoIP communications are no longer possible; they are not able to

switch their default gateway from router A to router B to access the IP network.

IP Network

Router A Router B

Default gateway of

the PBX: Router A

Default gateway of

the IP Telephone:

Router A

222 Installation Manual

7.1.6 Network Configuration

How is the PBX connected to remote extensions?

When the PBX is connected to a remote extensions via public IP network without using IP-VPN, address

translation techniques (e.g., NAT/NAPT) are used. These methods prevent VoIP communications from being

carried out effectively. In such cases, the use of a Session Border Controller (SBC) will avoid this problem.

Note

• An SBC is not required for:

– Connections via a Wide Area Ethernet or LAN

– Connections via IP-VPN

• An SBC is required for:

– Connections via a public IP network

Router

Global IP Address

Domain

Local IP Address

Domain

Local IP Address

Domain

Connection via IP-VPN

IP-VPN

Router

Switching Hub

Local IP Address

Domain

Connection via Wide Area Ethernet or LAN

Wide Area

Ethernet/

LAN

Installation Manual 223

7.1.6 Network Configuration

Router

Global IP Address

Domain

Local IP Address

Domain

Local IP Address

Domain

Connection via Public IP Network

Public

IP Network

SBC

Router

SBC

224 Installation Manual

7.1.6 Network Configuration

Are the network devices located appropriately for effective VoIP

communications?

Transmission delays can cause pauses and loss in VoIP communications. The more network devices (e.g.,

routers and switching hubs) there are between the PBX and IP telephones or the IP network interface, the

longer the transmission delays. This is because a certain amount of delay is inevitable when packets go through

each network device.

To prevent unnecessary delays, it is recommended to connect the PBX as close to the IP telephones and the

IP network interface as possible so that the number of the network devices is kept to a minimum.

IP Network

RouterRouter

Switching

Hub

Switching

Hub

Switching

Hub

Installation Manual 225

7.1.6 Network Configuration

7.1.7 Network Devices

You must evaluate the network devices that are used in the existing network to see if a VoIP network can be

implemented. Below are the points that should be evaluated.

Can the firewall pass packets appropriately?

If the VoIP network contains a firewall, the firewall must be configured appropriately to allow VoIP packets to

pass through the network without being blocked by filtering. For details about the protocols and port numbers

that the PBX uses for VoIP communication, refer to "7.5 Port Security".

The ports for which you need to configure the firewall may vary depending on the network conditions.

For more information, consult your network administrator.

Are layer 2 or higher switches used?

Use of repeater hubs can increase the network load, and therefore may result in degradation in speech quality.

To ensure high speech quality, use only layer 2 or higher switches. Use of layer 2 or higher switches is also

strongly recommended for connecting IP telephones.

Note

Note that the port of the switching hub that connects to the mother board should be set to operate under

"Auto Negotiation" mode.

Does all equipment on the LAN support 1000BASE-T connection?

To use the Gigabit Ethernet feature for the LAN, all equipment on the LAN must support 1000BASE-T. For

more information, consult your network administrator.

Are Category 5 (CAT 5) or higher cables used for 10BASE-T/100BASE-TX?

When connecting network devices, make sure to use CAT 5 or higher cables for 10BASE-T/100BASE-TX

connection. If other types of cables are used, communication may not be carried out normally.

Are Enhanced Category 5 (CAT 5e) or higher cables used for 1000BASE-T?

When connecting network devices, make sure to use CAT 5e or higher cables for 1000BASE-T. If other types

of cables are used, communication may not be carried out normally.

226 Installation Manual

7.1.7 Network Devices

7.1.8 QoS (Quality of Service)

Some routers permit the configuration of priority control features. This allows the router to give higher priority

to voice packets and lower the rate of loss and delays during transmissions, hence improving speech quality.

It is strongly recommended that you use this feature, especially in networks where traffic is heavy.

Typically, a router identifies what packets to pass in priority by checking the value in the ToS field of the header

of IP packets. The V-IPGW16 card has the ability to set the ToS field of outgoing voice packets. When the card

is appropriately configured, the router can give voice packets from the card higher priority.

Consult your network administrator when setting the ToS field, as the setting value must conform to the

router’s specifications.

Note

• Some switches also permit the configuration of priority control features. For more information, consult

your network administrator.

• To adjust the value in the ToS field, refer to "9.11 PBX Configuration—Configuration—Slot—V-IPGW16

—Shelf Property" in the PC Programming Manual.

Installation Manual 227

7.1.8 QoS (Quality of Service)

7.2 H.323 Trunks

This section explains information that is necessary for setting up a H.323 QSIG network over an IP network.

7.2.1 Avoid Multiple IP Networks

A huge degradation in speech quality will be produced when calls are made through multiple IP networks as

shown below; therefore, it is recommended that you avoid establishing a VoIP network in this fashion.

IP Network 1 IP Network 2

PSTN/

BRI QSIG, etc.

IP Network 1 IP Network 2

228 Installation Manual

7.2.1 Avoid Multiple IP Networks

7.2.2 Gatekeeper

The following are the general functions of a gatekeeper:

• Dialled number-to-IP address translation

• Authentication

• Bandwidth control

The gatekeeper provides these network management functions to registered clients. To register with the

gatekeeper, you need to configure the V-IPGW16 card to use the gatekeeper and programme the GK Settings

table through system programming. For details, refer to "9.11 PBX Configuration—Configuration—Slot—

V-IPGW16—Shelf Property— Gatekeeper Available" and "9.11.1 PBX Configuration—Configuration—Slot

—V-IPGW16—Shelf Property—GK Settings" in the PC Programming Manual. After programming, the

V-IPGW16 card attempts to register with the gatekeeper using registration information such as the IP address

of the mother board, and destination telephone numbers specified in the GK Settings table.

Note

• For more information about gatekeeper functions, consult the documentation of the gatekeeper.

• When using a gatekeeper, make sure to choose a compatible model. For more information about

gatekeeper compatibility with the V-IPGW16 card, consult a certified dealer.

7.2.3 Bandwidth Assessment

When using the IP telephones and V-IPGW16 card, you must ensure that the IP network in use has enough

bandwidth to support VoIP communications. If the amount of bandwidth required for VoIP communications is

more than the network can accommodate, speech quality will be compromised. In addition, there may be an

adverse effect on the performance of other applications (e.g., e-mail or Web applications) that use the same

network. Therefore, care must be taken when assessing bandwidth requirements.

Inform your network administrator of the required bandwidth, and make sure that the network can support VoIP

communications even under conditions of maximum network traffic.

Bandwidth Assessment for IP Extension Card

Required Bandwidth per IP Telephone for a Call

The required bandwidth depends on what combination of codecs and packet sending intervals is used. Keep

in mind the following points about the type of codecs and packet sending intervals, in terms of speech quality:

• The speech quality of the codecs varies as follows: (High) G.722, G.711, G.729A (Low)

• The shorter the packet sending interval, the higher the speech quality.

• The higher the speech quality the IP telephones provide, the more bandwidth the IP telephones require.

When the preferred codec of each party differs, the call will be established using the lower codec. For example, if the caller prefers

G.711 while the called party prefers G.729A, the call will be established using G.729A.

Codec

Packet Sending Interval

20 ms 30 ms 40 ms 60 ms

G.722

/G.711 87.2 kbps 79.5 kbps — —

G.729A 31.2 kbps 23.5 kbps 19.6 kbps 15.7 kbps

G.722 is only available for calls between KX-NT300 series IP-PTs and some SIP phones that support this codec during peer-to-peer

communication. For details, refer to "5.2.1.4 Peer-to-Peer (P2P) Connection" in the Feature Guide.

Installation Manual 229

7.2.3 Bandwidth Assessment

Required Bandwidth for Each IP Extension Card

To allow all IP telephones to make calls simultaneously, it is necessary to keep available the bandwidth required

by an IP extension card with the maximum number of IP telephones connected.

Provided below is the formula to calculate the amount of bandwidth required for each IP extension card.

When using the V-IPEXT32/V-SIPEXT32 card:

Required Bandwidth = (Required Bandwidth per IP telephone ´ 32)

Bandwidth Assessment for V-IPGW16 Card

Required Bandwidth for One VoIP Channel

The required bandwidth depends on what combination of codecs and packet sending intervals is used. Keep

in mind the following points about the type of codec and packet sending interval, in terms of the speech quality:

• The speech quality of the G.711 codec is higher than that of the G.729A codec.

• The shorter the packet sending interval, the higher the speech quality.

• The higher the speech quality the V-IPGW16 card provides, the more bandwidth the card requires.

Via LAN

Codec

Packet Sending Interval

20 ms 30 ms 40 ms 60 ms 90 ms

G.711 87.2 kbps 79.5 kbps 75.6 kbps 71.7 kbps —

G.729A 31.2 kbps 23.5 kbps 19.6 kbps 15.7 kbps —

Via WAN (PPP: Point-to-Point Protocol)

Codec

Packet Sending Interval

20 ms 30 ms 40 ms 60 ms 90 ms

G.711 84 kbps 77.3 kbps 74 kbps 70.7 kbps —

G.729A 28 kbps 21 kbps 18 kbps 14.7 kbps —

Bandwidth Calculation

Provided below is the formula to find out the amount of bandwidth required for VoIP communications:

Required Bandwidth

= (No. of Fax Machines ´ Required Bandwidth for the G.711 codec) +

[(16 - No. of Fax Machines) ´ Required Bandwidth for Voice Communication]

Example

Consider the following case as an example:

• Communication: via LAN

• No. of Fax Machines: 2

• G.711 Packet Sending Interval: 20 ms (requiring 87.2 kbps per channel)

• G.729A Packet Sending Interval for Voice Communication: 20 ms (requiring 31.2 kbps per channel)

In this case, the required bandwidth will be as follows:

Required Bandwidth

= (2 ´ 87.2) + [(16 - 2) ´ 31.2]

= 611.2 (kbps)

230 Installation Manual

7.2.3 Bandwidth Assessment

Therefore, inform your network administrator and make sure that the network can support a bandwidth of

611.2 kbps even when the network is under conditions of maximum traffic.

Note

It is recommended that all cards on a VoIP network have the same packet sending interval.

Additional Information

As described above, it is possible to control the required bandwidth by selecting a certain combination of codec

and packet sending interval. However, it is also possible to control required bandwidth by limiting the number

of available virtual VoIP channels.

The V-IPGW16 card supports a total of 8 ports, each having 2 separate channels. By disabling some of the

ports, you can reduce the bandwidth required for VoIP communications.

To limit the number of VoIP channels:

Set the status of the ports you wish to disable (starting from the highest-numbered port) to OUS.

For example, if you wish to use only 10 of the available 16 virtual VoIP channels (i.e., disable 6 channels), set

ports 8, 7, and 6 to OUS as shown below:

In this case, the equation for bandwidth calculation, based on the previous example, will change as follows:

Required Bandwidth

= (No. of Fax Machines ´ Required Bandwidth for the G.711 codec) +

[(

10 - No. of Fax Machines) ´ Required Bandwidth for Voice Communication]

= (2 ´ 87.2) + [(

10 - 2) ´ 31.2]

= 424 (kbps)

Installation Manual 231

7.2.3 Bandwidth Assessment

7.2.4 Virtual VoIP Gateway Card Specifications

For details about the RFCs and protocols for the V-IPGW16 card, refer to the following specifications.

ITU-T H.323

H.225.0

H.245

Codecs G.711 (a-law and µ-law)

G.729A

Voice Operations Echo Cancellation (48 ms)

Jitter Buffer (200 ms)

VAD (Voice Activity Detection)

PLC (Packet Loss Concealment)

DTMF Relay Inband/Outband (RFC2833)/Outband (H.245)

Fax Relay G.711 Inband/T.38

Protocol/Function RTP

RTCP

VAD is only available for codec G.711.

232 Installation Manual

7.2.4 Virtual VoIP Gateway Card Specifications

7.3 SIP Trunks

This section provides information on using SIP trunks with the PBX.

7.3.1 IP Telephony Service

The Virtual 16-Channel SIP Trunk Card (V-SIPGW16) is a virtual trunk card which is designed to be easily

integrated into an Internet Telephony Service provided by an ITSP (Internet Telephony Service Provider).

As a major SIP Provider, an ITSP provides its telephony service partly through the conventional telephone

network (e.g., ISDN and Mobile), which is fee-based. An ISP (Internet Service Provider), another major SIP

Provider, does not provide telephone connection itself. However, providing its users with Internet access, an

ISP provides voice communication on the Internet for free. In this way, with VoIP technology based on the SIP

protocol, the cost of voice communication can be much cheaper than conventional telephone networks. A

maximum of 16 V-SIPGW16 cards can be installed to the virtual slots of the PBX. The channel capacity of the

card allows users to connect to up to 32 different ISP/ITSPs.

V-SIPGW16 Connection Outline

The following diagram illustrates a simple VoIP network connecting the V-SIPGW16 card to the Internet.

PBX with

V-SIPGW16 Card

LAN

(Local Area Network)

WAN (Wide Area Network)

Internet

Local

Telephone

IP-PT

ISP

ITSP

Router

Switching

Hub

Requirements for Internet Telephony Service

• You need to subscribe with an ISP for Internet connection.

Installation Manual 233

7.3.1 IP Telephony Service

• You need to subscribe with an ITSP for telephone connection. The ISP and ITSP may be part of the same

company.

Note

• VoIP communication using the V-SIPGW16 card may deteriorate depending on the ITSP being used.

• VoIP communication using the V-SIPGW16 card may deteriorate depending on the network conditions.

DNS (Domain Name System)

A DNS server normally provides the name resolution service for your PC. As domain names are alphabetic,

they are easier to remember. The Internet, however, is based on IP addresses. Therefore, every time a domain

name is used, a DNS server must translate the name into the corresponding IP address, and vice versa. For

example, the domain name www.example.com may be translated to 192.0.34.166. If one DNS server does

not know how to translate a particular domain name, it asks another one, and so on, until the correct IP address

is returned.

NAT (Network Address Translation) Traversal

When NAT/NAPT (Network Address Port Translation) is enabled, the router translates a local IP address from

the PBX into a global IP address. However, the router with NAT enabled does not translate local IP addresses

stored in SIP messages into global IP addresses.

Therefore, the address which the SIP Server recognises as the destination IP address to reply to is actually

the local IP address of the PBX, not the global IP address of the router. Therefore, if the SIP Server receives

a SIP message from the PBX and sends a message back to the PBX using the address stored in the SIP

message, the packet information will not reach the PBX.

STUN Servers function to solve the global IP address problem under certain NAT conditions, for example, in

case of full duplex communication. A STUN Server, used alongside the SIP Server, finds out the global IP

address of the router with NAT enabled. With the STUN feature enabled, the packet information sent by the

SIP Server is able to "traverse" NAT and reach the PBX.

The settings can be configured to specify whether to enable the NAT Traversal feature for each ISP/ITSP. In

addition, the NAT Traversal method can be selected from "STUN" and "Fixed IP Address". For details, refer

to "9.8 PBX Configuration—Configuration—Slot—V-SIPGW—Shelf Property" in the PC Programming Manual.

The V-SIPGW16 card may require the NAT Traversal feature to be enabled to connect to the WAN via a router.

The following diagram illustrates how VoIP communication is enabled between the V-SIPGW16 card and the

SIP Server (SIP Receiver) via a router with NAT enabled.

234 Installation Manual

7.3.1 IP Telephony Service

LAN

WAN

Internet

STUN

Server

SIP

Server

Fixed IP Address

SIP

Server

STUN

Server

SIP

Server

Fixed IP Address

SIP

Server

PBX with

V-SIPGW16 Card

ISP/ITSP

Router

(NAT enabled)

IP-PT

Switching

Hub

Note

• If an ISP/ITSP uses a device such as SBC (Session Border Controller), you may not have to enable

the NAT Traversal feature.

• A STUN Server is supplied by an ISP/ITSP, and not included with the PBX.

Installation Manual 235

7.3.1 IP Telephony Service

7.3.2 SIP Requirements

Port Requirements

Required Ports for Each Channel

When configuring a router with NAT enabled, you need to secure a certain number of ports for each SIP and

RTP/RTCP channel. For RTP/RTCP, the number of required ports is double the number of activated SIP trunks

(Ch). For SIP signalling, the number of required ports is always one regardless of the number of activated SIP

trunks (Ch).

If 4 SIP trunk channels are activated, you need the following number of ports:

Protocol Type

Required Port

RTP 4

RTCP 4

SIP 1

Total 9

Firewall Requirements

If the VoIP network contains a firewall, the firewall must be configured appropriately to allow VoIP packets to

pass through the network without being blocked by filtering. For the protocols and port numbers that the PBX

uses for VoIP communication, refer to "7.5 Port Security".

The ports for which you need to configure the firewall may vary depending on the network conditions.

For more information, consult your network administrator.

7.3.3 Router Requirements

• Port Forwarding:

It may be necessary to set the NAT router so that it forwards the incoming packets to the IP address of the

V-SIPGW16 card if all of the following conditions are met:

– the PBX uses a STUN server;

– a V-SIPGW16 card is located under a NAT router;

– incoming packets are routed to a SIP Client port or NAT Voice (RTP) UDP port indicated in "7.5 Port

Security".

• SIP-NAT Feature:

When a V-SIPGW16 card is located under a NAT router that supports the SIP-NAT feature

, it is

recommended to disable this feature.

When NAT is enabled, the router translates the IP address stored in the IP header and the port number stored in the UDP header.

When SIP-NAT is enabled, the router also translates the IP address and port number stored in SIP messages.

7.3.4 Bandwidth Requirements

When using the V-SIPGW16 card, you must ensure that the WAN has enough bandwidth to support VoIP

communications. Refer to the table below and ensure that the sum of the required bandwidth for each channel

is smaller than the amount the WAN (e.g., ADSL network) can provide.

236 Installation Manual

7.3.4 Bandwidth Requirements

Note that the amount in the table is only a guide. Subscribe to a network that has enough bandwidth. If the

amount of bandwidth required for VoIP communications is larger than what the network can accommodate,

speech quality will be compromised.

Required Bandwidth for Each Channel

The required bandwidth depends on what combination of codecs and packet sending interval is used. Keep

in mind the following points about the type of codec and packet sending interval, in terms of the speech quality:

• The speech quality of the codecs varies as follows: G.711 (High), G.729A (Low)

• The shorter the packet sending interval, the higher the speech quality.

• The higher the speech quality the V-SIPGW16 card provides, the more bandwidth the WAN requires.

Codec

Packet Sending Interval

10 ms 20 ms 30 ms 40 ms 50 ms 60 ms

G.711 110.4 kbps 87.2 kbps 79.5 kbps 75.6 kbps 73.3 kbps 71.7 kbps

G.729A 54.4 kbps 31.2 kbps 23.5 kbps 19.6 kbps 17.3 kbps 15.7 kbps

Installation Manual 237

7.3.4 Bandwidth Requirements

7.3.5 Virtual SIP Trunk Card Specifications

For details about the RFCs and protocols for the V-SIPGW16 card, refer to the following specifications.

Items Specification

SIP RFCs RFC3261 (UDP only)

RFC3262 (PRACK)

RFC3264 (Offer/Answer)

RFC3311 (UPDATE)

RFC3581 (Symmetric Response Routing/rport)

RFC4028 (Session Timer)

Codecs G.711 (a-law and µ-law)

G.729A

Voice Options Echo Cancellation (48 ms)

Jitter Buffer (200 ms)

VAD (Voice Activity Detection)

PLC (Packet Loss Concealment)

DTMF Relay Inband/Outband (RFC2833)/Outband (SIP INFO)

Fax Relay G.711 Inband/T.38

Protocol/Function RTP

RTCP

DNS (A/SRV)

NAT Traversal (STUN)

QoS (ToS field setting in IP header of RTP/RTCP)

VAD is only available for codec G.711.

238 Installation Manual

7.3.5 Virtual SIP Trunk Card Specifications

7.4 Types of PBX Networks

This section gives an overview of the types of networks the PBX can participate in.

7.4.1 One-look Network

This section gives an overview of One-look networks.

Image of a One-look network:

Master Unit

Slave Unit Slave Unit Slave Unit

One-look Network

Features

• A maximum of 16 PBXs can be connected in a One-look network.

• The PBXs specified as Slave units use settings provided by the PBX specified as the Master unit, so a

considerable amount of setup is done automatically.

• Resource sharing allows users to interact as if they were all connected to one PBX, which eliminates the

need to manage information such as PBX access codes.

• All units in a One-look network can be programmed from one location.

Note

The MASTER indicator LED indicates whether the unit is configured as a Master unit or Slave unit. For

details, refer to "LED Indications".

Conditions

• A One-look network must consist only of KX-NS1000 PBXs.

• The sites that will be included in a One-look network must be connected over a private IP network before

setting up the One-look network.

Bandwidth Requirements

When implementing a One-look network, you must ensure that the IP network has enough bandwidth to support

both VoIP communication and One-look network signalling between PBXs. If the amount of bandwidth required

for VoIP communications and signalling is more than the network can accommodate, speech quality will

degrade. In addition, there may be an adverse effect on the performance of other applications (e.g., e-mail or

Web applications) that use the same network. Therefore, care must be taken when assessing bandwidth

requirements.

Installation Manual 239

7.4.1 One-look Network

Inform your network administrator of the required bandwidth, and make sure that the network can support VoIP

communications and signalling even under conditions of maximum network traffic.

Required Bandwidth per Call

The required bandwidth depends on the following factors:

• The maximum number of simultaneous calls

• Packet sending interval

• Type of codec used

• Telephone type

Keep in mind the following points about the types of codecs and packet sending intervals, in terms of speech

quality:

• The speech quality of the codecs varies as follows: (High) G.722, G.711, G.729A (Low)

• The shorter the packet sending interval, the higher the speech quality.

• The higher the speech quality an IP telephone provides, the more bandwidth it requires.

When the preferred codec of each party differs, the call will be established using the lower quality codec.

For example, if the caller prefers G.711 while the called party prefers G.729A, the call will be established using

G.729A.

Number of Simultaneous Calls

The number of simultaneous calls is proportional to number of extensions registered to the PBX, as shown in

the chart below. The proportion is approximately 0.25 when the number of registered extensions is 100. For

more information about the number of simultaneous calls, ask your local Panasonic dealer.

100

30020010010 50 150 250

Number of Simultaneous Calls

Number of Registered Extensions

Number of Registered

Extensions

10 50 100 150 200 250 300

Number of Simultaneous

Calls

6 16 26 35 44 53 61

Required Bandwidth per Call for VoIP Communication

The required bandwidth for VoIP communication is determined by the codec used and the packet sending

interval.

240 Installation Manual

7.4.1 One-look Network

Codec

Packet Sending Interval

20 ms 30 ms 40 ms 60 ms

G.711/G.722 80 kbps 74.7 kbps 72 kbps 69.4 kbps

G.729A 24 kbps 18.7 kbps 16.0 kbps 13.4 kbps

G.722 is only available for calls between KX-NT300 series IP-PTs and some SIP phones that support this codec during peer-to-peer

communication. For details, refer to "5.2.1.4 Peer-to-Peer (P2P) Connection" in the Feature Guide.

Required Bandwidth per Call for Signalling

In a One-look network, a certain amount of bandwidth is required for the master unit to handle all the calls in

the network. The required bandwidth depends on the type of IP telephone.

Phone Type

Required Bandwidth

IP Telephones (except SIP phones) 7.2 kbps

SIP Phone 16.0 kbps

Example:

The following examples show different cases of assessing bandwidth for a One-look network.

In this example, there are 3 PBXs in a One-look network.

Master Unit

Slave Unit A

- Number of Extensions: 100

- Extension Type: IP-PT

- Number of Simultaneous Calls: 26

Slave Unit B

- Number of Extensions: 50

- Extension Type: SIP Phone

- Number of Simultaneous Calls: 12

IP Network BIP Network A

Codec: G.711

Packet Interval: 20 ms

Bandwidth assessment for IP network A:

• Bandwidth required for VoIP communication

= Number of simultaneous calls ´ 2 ´ Required bandwidth for codecs (kbps)

= 26 ´ 2 ´ 80

= 4160 kbps

• Bandwidth required for signalling

= Number of simultaneous calls ´ Signalling bandwidth per a call for IP telephones (except SIP phones)

(kbps)

= 26 ´ 7.2

= 187.2 kbps

• Total required bandwidth for IP network A

= Bandwidth required for VoIP communication (kbps) + Bandwidth required for signalling (kbps)

= 4160 + 187.2

= 4347.2 kbps

Installation Manual 241

7.4.1 One-look Network

Bandwidth assessment for IP network B:

• Bandwidth required for VoIP communication

= Number of simultaneous calls ´ 2 ´ Required bandwidth for codecs (kbps)

= 12 ´ 2 ´ 80

= 1920 kbps

• Bandwidth required for signalling

Number of simultaneous calls ´ Signalling bandwidth per a call for SIP phones (kbps)

= 12 ´ 16

= 192 kbps

• Total required bandwidth for IP network B

= Bandwidth required for VoIP communication (kbps) + Bandwidth required for signalling (kbps)

= 1920 + 192

= 2112 kbps

Required Items

• KX-NSN001: Activation Key for One-look Network (One-look Network)

Networking Notes

• When setting up a PBX using Easy Setup Wizard, you specify whether the PBX will be the Master unit or

a Slave unit. For more details, refer to "5.4.1 Easy Setup Wizard".

• You can add Slave units to the One-look network using Web Maintenance Console. For more details, refer

to "5.5 Programming a One-look Network".

Note

• For more details about One-look networks, refer to "4.2 One-look Networking" in the Feature Guide.

• For details about configuring and programming a One-look networks, refer to "3.1.1 Home Screen—

Add Site Wizard" in the PC Programming Manual.

242 Installation Manual

7.4.1 One-look Network

7.4.2 H.323 QSIG Network

This section gives an overview of H.323 QSIG networks.

Image of a H.323 QSIG network:

Resources for Node 1

Node 1:

KX-NS1000

Resources for Node 2

Node 2:

KX-NCP500

H.323 QSIG

Network

Features

• H.323 QSIG networks can include non-KX-NS1000 PBXs (e.g., KX-TDE200, KX-NCP500).

• Resources are not available to extension users of other PBX without explicit configuration.

Conditions

• PBXs in an H.323 QSIG network must be connected over a private IP network.

Bandwidth Requirements

Refer to "7.2.3 Bandwidth Assessment".

Required Items

• V-IPGW16: Virtual 16-Channel VoIP Gateway Card

Note

The following activation key is required for enhanced QSIG network features (NDSS, Centralised Voice

Mail, etc.).

• KX-NSN002: Activation Key for QSIG Network (QSIG Network)

Networking Notes

When a KX-NS1000 is included in the H.323 QSIG network, the PBX must be specified as a Master unit.

Note

• For more details about H.323 QSIG networks, refer to "4.3.1 TIE Line Service" in the Feature Guide.

• For details about configuring and programming a H.323 QSIG network, refer to "

TIE Line Access"

in the PC Programming Manual.

Installation Manual 243

7.4.2 H.323 QSIG Network

7.4.3 Working with Multiple PBX Networks

It is possible to connect a One-look network to other PBXs via H.323 QSIG network. In an H.323 QSIG network,

the One-look network appears as one PBX.

Image of multiple PBX networks:

H.323 QSIG

Network

Master Unit

Slave Unit Slave Unit Slave Unit

Node 1:

One-look Network

Resources for Node 2

Node 2:

KX-NCP500

The following table shows the maximum number of sites/nodes that can be included in each type of network.

Network Type Method

Maximum Sites/

Nodes

Private Network One-look Network 16 sites

QSIG Network H.323 QSIG Network 512 nodes

Multiple PBX Networks One-look Network and H.323 QSIG Network 8192 sites

Note

For more details about using multiple PBX networks, refer to "Section 4, Network Features" in the Feature

Guide.

244 Installation Manual

7.4.3 Working with Multiple PBX Networks

7.5 Port Security

If the VoIP network contains a firewall, the firewall must be configured appropriately to allow VoIP packets to

pass through certain ports of the ports listed below without being blocked by filtering. The ports for which you

need to configure the firewall may vary depending on the network conditions.

For more information, consult your network administrator.

The following table shows the PBX’s ports used for IP communications. Any access to the ports not in this list

is ignored.

Port Numbers for LAN Port

Port Number Protocol Application Client/Server

Changeable/

Fixed

25 TCP/UDP SMTP Server Changeable

53 UDP DNS Server Fixed

67 UDP DHCP Server Changeable

68 UDP DHCP Client Changeable

80 TCP HTTP Server Changeable

123 UDP NTP Server Fixed

143 TCP IMAP Server Changeable

161 UDP SNMP Server Changeable

443 TCP HTTPS Server Changeable

465 TCP/UDP SMTP over SSL Server Changeable

993 TCP IMAP over SSL Server Changeable

1717 UDP Connectionless UDP - Changeable

1718 TCP Connectionless TCP - Changeable

1719 UDP H.225 RAS - Changeable

1720 TCP H.225 Call Signal - Changeable

2103 TCP CMM Server Fixed

2300 TCP Telnet-SMDR - Changeable

2727 UDP MGCP

- Changeable

3493 TCP UPS

- Fixed

3702 UDP WSD Server Changeable

4560–4561 UDP PSAP - Changeable

4562 UDP SSAP - Changeable

5060 UDP SIP UA (EXT) - Changeable

7547 TCP CWMP Server Changeable

7580 TCP HTTP Server Fixed

Installation Manual 245

7.5 Port Security

Port Number Protocol Application Client/Server

Changeable/

Fixed

8080 TCP Web Maintenance Console - Changeable

9300 UDP PTAP - Changeable

10000–

10655

TCP H.323 Dynamic Port

(H.225 Send, H.245 Send/

Receive, Connection-less

[TCP] Send Port)

- Changeable

20000 TCP UM-VMA

Server Fixed

30021 TCP/UDP FTP/FTPS Server Changeable

30022 TCP SSH Server Changeable

32727 UDP MGCP

for IP-CS - Changeable

33090 UDP ACS-MDW Server Fixed

33091

33092 TCP

33131

33321 TCP Access Point Login (Telnet) Server Changeable

33333 TCP CTI 3rd Party Connection - Changeable

33334 TCP CTI 1st Party Connection - Changeable

33478 UDP STUN Client Changeable

33702 UDP ACS-MDW (WSD) Server Fixed

35060 UDP SIP UA (CO) - Changeable

39300 UDP PTAP for IP-CS - Changeable

40000–

40095

TCP/UDP FTP/FTPS-Data Server Changeable

50000–

65535

(Ephemeral)

UDP SNMP TRAP Client Fixed

TCP/UDP FTP Client

TCP/UDP FTP/FTPS-Data Client

UDP NTP Client

UDP DNS Client

UDP SYSLOG Client

TCP/UDP SMTP Client

TCP/UDP SMTP over SSL Client

TCP/UDP POP3 Client

246 Installation Manual

7.5 Port Security

Port Number Protocol Application Client/Server

Changeable/

Fixed

TCP/UDP ACS-MDW Server

Media Gateway Control Protocol. Used for call control command data and LCD/LED data transmission.

Used by UPS daemon.

Used by Unified Messaging.

Port Numbers for MNT Port

Port Number Protocol Application Client/Server

Changeable/

Fixed

21 TCP/UDP FTP/FTPS Server Changeable

25 TCP/UDP SMTP Server Changeable

53 UDP DNS Server Changeable

67 UDP DHCP Server Changeable

80 TCP HTTP Server Changeable

123 UDP NTP Server Fixed

143 TCP IMAP Server Changeable

161 UDP SNMP Server Changeable

443 TCP HTTPS Server Changeable

465 TCP/UDP SMTP over SSL Server Changeable

993 TCP IMAP over SSL Server Changeable

2103 TCP CMM Server Fixed

2300 TCP Telnet-SMDR - Changeable

3493 UDP UPS

- Fixed

3702 UDP WSD Server Changeable

7574 TCP CWMP Server Changeable

8080 TCP Web Maintenance Console - Changeable

30022 TCP SSH Server Changeable

33090 UDP ACS-MDW Server Fixed

30091

30092 TCP

33131

33321 TCP Access Point Login (Telnet) Server Changeable

33333 TCP CTI 3rd Party Connection - Changeable

33334 TCP CTI 1st Party Connection - Changeable

33702 UDP ACS-MDW (WSD) Server Fixed

Installation Manual 247

7.5 Port Security

Port Number Protocol Application Client/Server

Changeable/

Fixed

40000–

40095

TCP/UDP FTP/FTPS-Data Server Changeable

50000–

65535

(Ephemeral)

UDP SNMP TRAP Client Fixed

TCP/UDP FTP Client

TCP/UDP FTP/FTPS-Data Client

UDP NTP Client

UDP DNS Client

UDP SYSLOG Client

TCP/UDP SMTP Client

TCP/UDP SMTP over SSL Client

TCP/UDP POP3 Client

TCP/UDP ACS-MDW Server

Used by UPS daemon.

Port Numbers for Optional DSP Cards

Port Number Protocol Application Client/Server

Changeable/

Fixed

21 TCP/UDP FTP/FTPS Server Changeable

25 TCP/UDP SMTP Server Changeable

53 UDP DNS Server Changeable

67 UDP DHCP Server Changeable

68 UDP DHCP Client Changeable

123 UDP NTP Server Fixed

143 TCP IMAP Server Changeable

161 UDP SNMP Server Changeable

465 TCP/UDP SMTP over SSL Server Changeable

993 TCP IMAP over SSL Server Changeable

2103 TCP CMM Server Fixed

3493 TCP UPS - Fixed

3702 UDP WSD Server Changeable

7547 TCP CWMP Server Changeable

8000 UDP Conference

- Fixed

8080 TCP Web Maintenance Console - Changeable

248 Installation Manual

7.5 Port Security

Port Number Protocol Application Client/Server

Changeable/

Fixed

12000–

13535

UDP RTP/RTCP - Changeable

16000–

18047

UDP RTP/RTCP for NAT traversal - Changeable

30022 TCP SSH Server Changeable

33090 UDP ACS-MDW Server Fixed

33091

33092 TCP

33131

33702 UDP ACS-MDW (WSD) Server Fixed

40000–

40095

TCP/UDP FTP/FTPS-Data Server Changeable

50000–

65535

(Ephemeral)

UDP SNMP TRAP Client Fixed

TCP/UDP FTP Client

TCP/UDP FTP/FTPS-Data Client

UDP NTP Client

UDP DNS Client

UDP SYSLOG Client

TCP/UDP SMTP Client

TCP/UDP SMTP over SSL Client

TCP/UDP POP3 Client

TCP/UDP ACS-MDW Server

Used for KX-NS1000 conferences.

Installation Manual 249

7.5 Port Security

7.6 PBX Region Suffix Codes and Areas

According to the following table, select the appropriate Suffix Code and Area for your PBX to localise PBX

settings to your location.

For KX-NS1000NE

Suffix Code Area Suffix Code Area

G Germany CE Poland

Austria Hungary

BL Belgium Czech

Luxembourg Slovakia

DK Denmark Romania

FI Finland Slovenia

FR France Croatia

JT Italy Yugoslavia

NL Netherlands Bosnia

NO Norway Lithuania

PT Portugal Latvia

SP Spain Estonia

SE Sweden Albania

SL Switzerland Bulgaria

TR Turkey Macedonia

GR Greece Other

For KX-NS1000XE

Suffix Code

Area

HK Hong Kong

ML Malaysia

SN Singapore

TW Taiwan

BX Other

For KX-NS1000BX

Suffix Code

Area

SA South Africa

BX Other

250 Installation Manual

7.6 PBX Region Suffix Codes and Areas

For KX-NS1000AL

Suffix Code Area

AL Australia

NZ New Zealand

Installation Manual 251

7.6 PBX Region Suffix Codes and Areas

7.7 System Prompt Languages

Note

• The following abbreviations are used in the language file names:

– UK: United Kingdom

– US: United States

– LA: Latin America

– CA: Canada

– BR: Brazil

• No. 1 is set by default. For details, see "24.1.1 UM Configuration—System Parameters—Parameters

—Prompt Setting—Prompt Setting" in the PC Programming Manual.

System prompt languages stored in the Storage Memory Card (installed by default)

KX-NS1000

Suffix

NE UK/AL XE BX AG

No. 1

(Primary)

UK-English UK-English US-English US-English LA-Spanish

No. 2 Spanish - LA-Spanish LA-Spanish US-English

No. 3 French - Mandarin - -

No. 4 German - Taiwan

Mandarin

- -

No. 5 Dutch - Cantonese - -

No. 6 Italian - - - -

No. 7 Swedish - - - -

No. 8 - - - - -

KX-NS1000

Suffix

C RU UC BR

No. 1

(Primary)

CA-English Russian Ukrainian BR-Portuguese

No. 2 CA-French Ukrainian Russian US-English

No. 3 - US-English US-English -

No. 4 - - - -

No. 5 - - - -

No. 6 - - - -

No. 7 - - - -

No. 8 - - - -

252 Installation Manual

7.7 System Prompt Languages

System prompt languages stored in optional Storage Memory Cards

KX-NS0135/

KX-NS0136/

KX-NS0137

Suffix

No. 1

(Primary)

UK-English

No. 2 German

No. 3 Spanish

No. 4 Italian

No. 5 Swedish

No. 6 Dutch

No. 7 CA-English

No. 8 CA-French

Installation Manual 253

7.7 System Prompt Languages

254 Installation Manual

7.7 System Prompt Languages

Index

Installation Manual 255

Numerics

19-inch Rack Mounting 85

2-Port Analogue Trunk / 2-Port SLT Card

(KX-NS0180) 28, 104

4-Port BRI / 2-Port SLT Card (KX-NS0280) 28, 106

Accessing Port Properties 160

Activation Key Code 56

Activation Key, Cellular Phone Extension 49

Activation Key, Communication Assistant (CA) User 50

Activation Key, IP Telephone 44

Activation Key, IP Telephone Capacity 43

Activation Key, IP Trunks 42

Activation Key, Networking 46

Activation Key, Unified Messaging System (Features) 46

Activation Key, Unified Messaging System (Mailbox) 48

Activation Key, Unified Messaging System (Two-way

Recording/Two-way Transfer Users) 49

Activation Key, Unified Messaging System (Unified

Messaging Ports) 47

Address Translation Table 154

Assigning the Hunt Pattern 153

BGM 123

Cable Distance 118

Characteristics 31

Connection Chart for LAN Connection 127

Connection Diagram, System 26

Connector Types 83

CTI Server Connection (via LAN Port) 127

CTI—Third Party Call Control 127

DHCP server feature 219

Diffserv (Differentiated Services) 183

DNS (Domain Name System) 234

DNS Server 234

Door Opener 116, 119

Doorphone 116, 119

Doorphone Interface Card (KX-NS0161) 28, 116

Error Log 213

Extension Number Method 157

External Sensor 117, 119

FAX Interface Card (KX-NS0106) 28, 101

Ferrite Core 84

Fixed IP Address 234

Frame Earth Connection 65

Gatekeeper 229

Information about the Virtual Cards 102

Installation Precautions 58

Installing Activation Key Files 149

Installing Virtual IP Cards 149

IP Telephone, AC Adaptor Connection 130

IP Telephone, Assigning IP Address 162

IP Telephone, De-registration 198

IP Telephone, Forced De-registration 199

IP Telephone, PC Connection 130

IP Telephone, Registering (Extension Number Input

Mode) 192

IP Telephone, Registering (Manual Mode) 193

IP Telephone, Switching Hub Connection 129

ISP (Internet Service Provider) 233

ITSP (Internet Telephony Service Provider) 233

Jitter Buffer 221

Key Management System 56

KX-NS0106 (FAX Interface Card) 28, 101

KX-NS0110 (VoIP DSP Card (S Type)) 28, 99

KX-NS0111 (VoIP DSP Card (M Type)) 28, 99

KX-NS0112 (VoIP DSP Card (L Type)) 28, 99

KX-NS0135 (Storage Memory (S Type)) 28, 98

KX-NS0136 (Storage Memory (M Type)) 28, 98

KX-NS0137 (Storage Memory (L Type)) 28, 98

KX-NS0161 (Doorphone Interface Card) 28, 116

KX-NS0180 (2-Port Analogue Trunk / 2-Port SLT

Card) 28, 104

KX-NS0280 (4-Port BRI / 2-Port SLT Card) 28, 106

KX-NS0290 (PRI23 / 2-Port SLT Card) 29, 113

KX-NS0290CE (PRI30 / 2-Port SLT Card) 29, 110

Main Unit 24

MOH 123

Mother board 94

Names and Locations 61

NAT (Network Address Translation) 223

NAT Traversal 234

One-Look Network 24

Opening/Closing the Top Cover 62

Optional Equipment 28

Optional Service Card, Installation 71

Optional Service Card, Maximum Number 32

Optional Service Card, Removal 74

256 Installation Manual

Index

Pager 123

Password Security 142

PBX Code Method 156

PC Connection (via MNT Port) 122

PC/Printer Connection (via RS-232C) 123

Placing the PBX on a Desktop 86

Power Failure Ports 132

PRI23 / 2-Port SLT Card (KX-NS0290) 29, 113

PRI30 / 2-Port SLT Card (KX-NS0290CE) 29, 110

QoS (Quality of Service) 227

Safety Installation Instructions 58

SBC (Session Border Controller) 235

Slot for the Mother board 32

Slots for Physical Cards (Free Slots) 32

Slots for Virtual Extension Cards 32

Slots for Virtual Trunk Cards 32

Specifications, Characteristics 31

Specifications, General Description 30

Specifications, System Capacity 32

Specifications, V-IPGW16 232

Specifications, V-SIPGW16 238

Stand-alone system 24

Starting the PBX 133

Storage Memory (L Type) (KX-NS0137) 28, 98

Storage Memory (M Type) (KX-NS0136) 28, 98

Storage Memory (S Type) (KX-NS0135) 28, 98

Storage Memory Card, Installation 79

Storage Memory Card, Removal 79

STUN 234

STUN Server 234

Surge Protector Installation 91

System Capacity 32

System Connection Diagram 26

System Initialisation Procedure 135

System Mode Switch 133, 211

System Requirements 142

Terminal Equipment, Maximum Number 38

Troubleshooting, by Error Log 213

Troubleshooting, Connection 206

Troubleshooting, Error Messages 209

Troubleshooting, Installation 204

Troubleshooting, Operation 207

Trunk Connection 136

Unpacking 60

UPS Connection 125

USB memory device 125

V-IPCS4 (Virtual 4 IP Cell Station Interface Card) 102

V-IPEXT32 (Virtual 32-Channel VoIP Extension Card) 102

V-IPGW16 (Virtual 16-Channel VoIP Gateway Card) 102

V-IPGW16, Bandwidth Requirements 229

V-IPGW16, Firewall Requirements 226

Virtual 16-Channel SIP Trunk Card (V-SIPGW16) 102

Virtual 16-Channel VoIP Gateway Card (V-IPGW16) 102

Virtual 32-Channel SIP Extension Card (V-SIPEXT32) 102

Virtual 32-Channel VoIP Extension Card (V-IPEXT32) 102

Virtual 4 IP Cell Station Interface Card (V-IPCS4) 102

Virtual Slot 32

Virtual UT Extension Card (V-UTEXT32) 102

VLAN (Virtual LAN) 180, 220

Voice Activity Detection (VAD) 221

VoIP DSP Card (L Type) (KX-NS0112) 28, 99

VoIP DSP Card (M Type) (KX-NS0111) 28, 99

VoIP DSP Card (S Type) (KX-NS0110) 28, 99

VoIP Network 216

V-SIPEXT32 (Virtual 32-Channel SIP Extension Card) 102

V-SIPGW16 (Virtual 16-Channel SIP Trunk Card) 102

V-SIPGW16 Connection Outline 233

V-SIPGW16, Adding Settings to Provider Profiles 161

V-SIPGW16, Automatic Programming 160

V-SIPGW16, Bandwidth Requirements 237

V-SIPGW16, Firewall Requirements 236

V-SIPGW16, Important Notice for Subscription and

Installation 236

V-SIPGW16, Manual Programming 160

V-SIPGW16, Port Requirements 236

V-SIPGW16, Programming Port Property 160

V-SIPGW16, Router Requirements 236

V-UTEXT32 (Virtual UT Extension Card) 102

Web Maintenance Console 138

Web Maintenance Console, Easy Setup Wizard 145

Web Maintenance Console, Password Security 142

Web Maintenance Console, PC Connection 139

Web Maintenance Console, Starting 143

Web Maintenance Console, System Requirements 142

Wiring Precautions 59

Installation Manual 257

Index

The KX-NS1000UK and KX-NS1000NE are designed to interwork with the:

• Analogue Public Switched Telephone Network (PSTN) of European countries

• Pan-European Integrated Services Digital Network (ISDN) using ISDN basic rate access

• Pan-European Integrated Services Digital Network (ISDN) using ISDN primary rate

access

Panasonic System Networks Co., Ltd./Panasonic System Networks Company U.K. Ltd. declares that the KX-NS1000UK

and the KX-NS1000NE are in compliance with the essential requirements and other relevant provisions of Radio &

Telecommunications Terminal Equipment (R&TTE) Directive 1999/5/EC.

Declarations of Conformity for the relevant Panasonic products described in this manual are available for download by

visiting:

http://www.doc.panasonic.de

Contact to Authorised Representative:

Panasonic Testing Centre

Panasonic Marketing Europe GmbH

Winsbergring 15, 22525 Hamburg, Germany

Installation Manual 259

Notes

1-62, 4-chome, Minoshima, Hakata-ku, Fukuoka 812-8531, Japan

This material is copyrighted by Panasonic System Networks Co., Ltd., and may be reproduced for internal use

only. All other reproduction, in whole or in part, is prohibited without the written consent of Panasonic

System Networks Co., Ltd.

Panasonic System Networks Co., Ltd. 2011

DD1111HH2052

For Future Reference

Please print, record, and retain the following information for future reference.

The serial number of this product can be found on the label affixed to the unit. You should record

the model number and the serial number of this unit as a permanent record of your purchase to

aid in identification in the event of theft.

Note

MODEL NO.

SERIAL NO.

DATE OF PURCHASE

NAME OF DEALER

DEALER'S ADDRESS

DEALER'S TEL. NO.

Web Site: http://www.panasonic.net/

PNQX3640XA